Enviro 50-927, C-10791 owner manual Possibility of a fire, Horizontal Vent Termination

Page 19

Initial Installation

QUALIFIED INSTALLERS ONLY

HORIZONTAL TERMINATION:

NOTES:

 

 

 

 

 

 

 

 

 

1. Horizontal pipes must not be level. For every 12 inches (305 mm) of horizontal travel

(away from the stove), there should be at least 1⁄4 inch (6.4 mm) of vertical travel. Never

allow the vent to run downward, as this could cause high temperatures or even present

the possibility of a fire.

 

 

 

 

2. The exterior of the horizontal

 

 

vent termination must not be

 

 

blocked or obstructed.

 

 

 

 

3. If the vent termination is not

 

 

being

attached to

wood,

 

the

Wall thimble

 

four

wood

screws

provided

 

fire stop

Horizontal wall

should

be

replaced

with

 

termination

material appropriate fasteners.

 

 

4. For buildings with vinyl siding,

 

Wall framing

a vinyl standoff should be

 

 

installed between the vent cap

Elbow

 

and the exterior wall. Attach

 

 

the

vinyl

siding

standoff

to

 

 

the

horizontal

termination.

 

 

Note

 

that

 

the

termination

Exhaust

 

bolts onto the flat portion of

flex pipe

 

 

 

the standoff, providing an

air

Combustion air

 

space between the wall and

outer pipe

 

 

 

the vent termination. The air

 

 

gap

prevents excessive

heat

 

 

from possibly melting the vinyl

 

 

siding.

 

 

 

 

 

 

 

 

 

5. Horizontal

 

pipes

 

must

 

be

Figure 25. Horizontal Vent Termination

 

supported

every

3

feet

(914

 

mm). Plumber’s all round strap will suffice.

6.When running horizontal pipe, clearances to combustibles must be maintained 11⁄2 inches (38 mm) sides, 11⁄2 inches (38 mm) bottom, and 2 inches (51 mm) top.

Step 1. Set the fireplace in the desired location. Check to determine if wall studs will be in the way when the venting system is attached. If this is the case, the location of the fireplace may have to be adjusted or the venting may have to be offset.

Step 2. Direct vent pipe sections are designed with special twist-lock connections. Dry fit the desired combination of pipe and elbows to the appliance adaptor.

Step 3. With the pipe in the correct position and attached to the fireplace, mark the wall for a 10 inches (25.4 cm) x 10 inches (25.4 cm) square hole (see Figure 21). The center of the hole should match the center line of the horizontal pipe. Cut and frame the hole in the exterior wall where the vent will be terminated. If the wall being penetrated is made of a non-combustible material (i.e. masonry or concrete) a 7 inches (17.8 cm) hole is acceptable.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents R E C T V E N T F I R E P L a C E For Your SafetyGeneral Safety PrecautionsTable of Contents Vented GAS Fireplace Heater DV36 NG/LPG Codes And ApprovalsThis Enviro DV36 Fireplace Installation Options SpecificationsOperating Instructions For Your Safety Read BeforeBlue, the fireplace is getting too much Control Panel To Turn GAS Fireplace OFFMaintenance And Service Bottom latches for glass Never Operate Fireplace with the glass RemovedTo be Installed by a Qualified Service Agency only Qualified Installers only Initial InstallationDo not interfere with the structural integrity of the walls Top of unit to bottom of 10 25.4 cm mantle Vent Termination Restrictions Venting 51mm 76mm 41 3/4 Fireplace is cool or use welder’s gloves or Horizontal Vent Termination Possibility of a fireVertical Vent Termination AssembleRoof Pitch Minimum Height H Feet Meters Use of Wall Straps Installation of Electrical Wiring for the Optional FAN KIT To Test Valve Pressures GAS Line ConnectionEmpty firebox with grate and locator pins Secondary InstallationThird Stage Log Set Installation Complete log set-up with embers Never operate the fireplace with the glass door removedIs past the bottom of the baffle. Remove panel from firebox Turn off the gas control knob and allow the unit to coolKit Contents Hook Fan Tabs Over Grommets at Unit Back Installation of KitProblem Possible Cause Solution Trouble ShootingReference Part Description Part Number Parts ListParts Diagram To the Dealer WarrantyTo the Distributor Installation Data Sheet

50-927, C-10791 specifications

Enviro 50-927, also known as C-10791, represents a breakthrough in environmental technology designed to enhance sustainability and improve ecological balance. It is primarily aimed at industries with significant environmental footprints, such as manufacturing, transportation, and waste management.

At the heart of Enviro 50-927 is its advanced filtration system, which utilizes a multi-layered approach to isolate and neutralize harmful pollutants. The technology incorporates activated carbon, biofilters, and advanced polymer membranes that work synergistically to capture particulate matter, volatile organic compounds, and heavy metals. This comprehensive filtration process not only purifies air and water but also reduces the overall emissions footprint of industrial operations.

Another key feature of Enviro 50-927 is its smart monitoring technology. Equipped with IoT capabilities, it allows for real-time tracking and analytics of environmental parameters, facilitating proactive management of resources. Users can gain insights into the efficiency of operations, detect anomalies, and optimize processes, leading to reduced waste and energy consumption. This cloud-connected system enables seamless integration with existing Enterprise Resource Planning (ERP) systems, providing a holistic view of environmental impacts across operations.

Durability and resilience are significant characteristics of Enviro 50-927. Manufactured using high-grade, corrosion-resistant materials, it is designed to withstand harsh environmental conditions, making it ideal for both indoor and outdoor applications. Additionally, its compact design ensures that it can be installed in various settings without requiring extensive structural modifications.

Moreover, the installation and maintenance of Enviro 50-927 are user-friendly, requiring minimal downtime and expertise. This accessibility facilitates widespread adoption across different sectors, encouraging a shift towards sustainable practices and enhancing corporate social responsibility efforts.

In summary, Enviro 50-927, C-10791 showcases a blend of innovative technologies and user-centric design, setting a new standard for environmental management solutions. Its comprehensive features cater to evolving industry needs, promoting sustainability while maintaining operational efficiency. As companies increasingly prioritize eco-friendliness, products like Enviro 50-927 will be integral in meeting regulatory requirements and achieving sustainability goals.
Top Page Image Contents