Enviro C-10791, 50-927 owner manual Assemble, Vertical Vent Termination

Page 20

Initial Installation

QUALIFIED INSTALLERS ONLY

NOTE: For Simpson Duravent only, place a bead of Mil-Pac or Rutland No 78 Stove and Gasket Cement on the outer edge of the inner exhaust pipe (non-flared end). Push the pipe sections together, then twist about 1⁄4 turn, making sure the two sections are fully locked. Wrap all seams with foil ducting tape.

Step 4. With the hole now framed, the wall thimble installed, and the pipe extending into the wall, proceed to the outside. Attach the termination to the pipe using RTV and Mil-Pac or Rutland No 78 Stove and Gasket Cement to seal joints. The vent pipe must extend into the vent cap at least 11⁄4 inches (3.2 cm). Secure the connection between the vent cap and the pipe by attaching the two (2) sheet metal straps, which extend from the vent cap assembly to the outer wall of the vent pipe. Bend any remaining portion of the strap back towards the vent cap. Security Secure Vent uses a twist lock cap.

Step 5. Position the horizontal vent termination in the center of the 10 inches (25.4 cm) square hole and attach to the exterior wall with the four screws provided. The arrow on the vent termination should be pointing up. Run a bead of non-hardening mastic around the edges of the vent cap, to make a seal with the wall. Ensure the proper clearances to combustibles have been maintained.

VERTICAL TERMINATION:

Step 1. Check the instructions for required clearances (air spaces) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafters, or other nearby combustible surfaces. Do not pack air spaces with insulation.

Step 2. Set the gas appliance in the desired location. Drop a plumb bob down from the ceiling to the position of the appliance flue exit, and mark the location where the vent will penetrate the ceiling. Drill a small hole at this point. Next, drop a plumb bob from the roof to the hole previously drilled in the ceiling, mark the spot where the vent will penetrate the roof. Determine if ceiling joists, roof rafters, or other framing will obstruct the venting system. You may wish to relocate the appliance, or to offset, to avoid cutting load bearing members.

Step 3. To install the Round Support Box/Wall Thimble in a flat ceiling, cut a 10 inch (25.4 cm) square hole in the ceiling, centered in the hole drilled in Step 2. Frame the hole as shown in Figure 21.

Step 4. Assemble

the desired

lengths

of

black

pipe

and elbows

necessary to

reach from the appliance

adapter

up

through

the

Round

Support

Box.

Insure that all pipe and

elbow

connections

are

in their fully twist-locked position.

 

Vertical

 

Termination

Elbow Strap

Storm Collar

 

Flashing

 

Roofing nails

Figure 26. Vertical Vent Termination

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents For Your Safety R E C T V E N T F I R E P L a C ESafety Precautions GeneralTable of Contents This Enviro DV36 Fireplace Codes And ApprovalsVented GAS Fireplace Heater DV36 NG/LPG Specifications Installation OptionsFor Your Safety Read Before Operating InstructionsBlue, the fireplace is getting too much To Turn GAS Fireplace OFF Control PanelMaintenance And Service Never Operate Fireplace with the glass Removed Bottom latches for glassTo be Installed by a Qualified Service Agency only Initial Installation Qualified Installers onlyDo not interfere with the structural integrity of the walls Top of unit to bottom of 10 25.4 cm mantle Vent Termination Restrictions Venting 51mm 76mm 41 3/4 Fireplace is cool or use welder’s gloves or Possibility of a fire Horizontal Vent TerminationAssemble Vertical Vent TerminationRoof Pitch Minimum Height H Feet Meters Use of Wall Straps Installation of Electrical Wiring for the Optional FAN KIT GAS Line Connection To Test Valve PressuresSecondary Installation Empty firebox with grate and locator pinsThird Stage Log Set Installation Never operate the fireplace with the glass door removed Complete log set-up with embersTurn off the gas control knob and allow the unit to cool Is past the bottom of the baffle. Remove panel from fireboxKit Contents Installation of Kit Hook Fan Tabs Over Grommets at Unit BackTrouble Shooting Problem Possible Cause SolutionParts List Reference Part Description Part NumberParts Diagram To the Distributor WarrantyTo the Dealer Installation Data Sheet

50-927, C-10791 specifications

Enviro 50-927, also known as C-10791, represents a breakthrough in environmental technology designed to enhance sustainability and improve ecological balance. It is primarily aimed at industries with significant environmental footprints, such as manufacturing, transportation, and waste management.

At the heart of Enviro 50-927 is its advanced filtration system, which utilizes a multi-layered approach to isolate and neutralize harmful pollutants. The technology incorporates activated carbon, biofilters, and advanced polymer membranes that work synergistically to capture particulate matter, volatile organic compounds, and heavy metals. This comprehensive filtration process not only purifies air and water but also reduces the overall emissions footprint of industrial operations.

Another key feature of Enviro 50-927 is its smart monitoring technology. Equipped with IoT capabilities, it allows for real-time tracking and analytics of environmental parameters, facilitating proactive management of resources. Users can gain insights into the efficiency of operations, detect anomalies, and optimize processes, leading to reduced waste and energy consumption. This cloud-connected system enables seamless integration with existing Enterprise Resource Planning (ERP) systems, providing a holistic view of environmental impacts across operations.

Durability and resilience are significant characteristics of Enviro 50-927. Manufactured using high-grade, corrosion-resistant materials, it is designed to withstand harsh environmental conditions, making it ideal for both indoor and outdoor applications. Additionally, its compact design ensures that it can be installed in various settings without requiring extensive structural modifications.

Moreover, the installation and maintenance of Enviro 50-927 are user-friendly, requiring minimal downtime and expertise. This accessibility facilitates widespread adoption across different sectors, encouraging a shift towards sustainable practices and enhancing corporate social responsibility efforts.

In summary, Enviro 50-927, C-10791 showcases a blend of innovative technologies and user-centric design, setting a new standard for environmental management solutions. Its comprehensive features cater to evolving industry needs, promoting sustainability while maintaining operational efficiency. As companies increasingly prioritize eco-friendliness, products like Enviro 50-927 will be integral in meeting regulatory requirements and achieving sustainability goals.
Top Page Image Contents