Vanguard VE36LBH, VE32LH manual Optional Heater Accessory, VE36LH Only, Retainer, Bracket

Page 10

Accessory

Installation

Continued

5.Insert brick panel, beveled edge first, through firebox opening. Tilt and angle top edge into brick retainer until beveled edge contacts imager and panel is flat against firebox (see Figure 20).

6.Align hearth pan bracket over holes near lower edge of brick panel and secure with 2 pan screws provided.

7.Replace refractory bracket using 2 screws removed in step 4, page 9.

8.Repeat steps 5 through 7 for opposite panel assembly.

9.Replace each screen assembly by po- sitioning screen rod into locating holes under top edge of firebox and securing with 2 Phillips screws removed in step 2, page 9. Note: Rods may have to be angled into locating holes at the top of each screen pocket. Once inserted, pull free end of rod forward until it lines up over farthest mounting hole respectively so rods overlap.

10.Replace log bed over hearth opening and center between grate and viewing screen.

11.Replace glass doors if removed. See Optional Glass Doors, page 8.

Face Panel

(Models VE36L

and VE36LH

Only)

Refractory

Hearth Pan Bracket

Bracket

(Models VE36L and

 

 

VE36LH Only)

Figure 19 - Removing Refractory Bracket

and Hearth Pan Bracket

Refractory

Refractory

Retainer

Bracket

Bracket

 

Hearth Pan

Bracket

Figure 20 - Installing Brick Panels and

Brackets

OPTIONAL HEATER ACCESSORY

WARNING: Disconnect power before attempting any maintenance or cleaning to re- duce the risk of fire, electrical shock or personal injury.

Blower/heater kit model BHKE is available for models VE36/32L and VE36/32LB. Either of 2 types of blower/heater assemblies can be installed.

1.Open upper control door (see Figure 13, on page 7) and remove 2 Phillips screws below heater grill on control panel (see Figure 21, page 11).

2.Remove 2 Phillips screws holding control cover to control panel inside firebox (see

Figure 14, page 8).

3.Slide control cover to the right and swing out locking tabs from notched openings on top (see Figure 21, page 11) .

4.Let control cover hang down off har- nesses. Be careful not to damage any wiring. If necessary, unscrew harness strap at blower mount to gain slack.

5.Remove 2 hex screws at rear of blower mount (see Figure 21, page 11).

6.Slide blower mount towards rear of firebox until locking tabs line up with notched openings and lower mount down and away (see Figure 21, page 11).

10

www.desatech.com

115121-01B

Image 10
Contents Electric Fireplace OWNER’S Operation and Installation Manual Table of Contents Safety InformationInstallation Product SpecificationLocating Fireplace Cabinet Mantel Installation Installation ClearancesFor mantel clearances see Figures 3 Universal Strain Relief Cord Mount Assembly BUILT-IN InstallationAccessory Cord Electric Outlet Wire NutsElectrical Installation Relocating Junction Box to LeftLamps and lava Rock Features OperationMotor Mount Foam Shipping Brace Accessory Installation Optional Glass DoorsSpring Clip Locating Hole Bifold doors may be removed for replacing or cleaningOptional Brick Liners Locating Holes Screen Rod Retaining ScrewRetainer Optional Heater AccessoryVE36LH Only BracketConnect white heater wire to neutral Wired for convenienceMount location with on I indicator Knockout Plug Remove to Install Power SwitchTerminal Block White Rocker Switch Red L-4 White N-1Terminal D Jumper Switch Lead Terminal L-5 RockerTroubleshooting Observed Problem Possible Cause RemedyWiring Diagram Heater Assembly Electrical DiagramMaintaining Motors MaintenanceReplacing Light Bulbs Removing/Replacing Control DoorAngle control panel out through opening see Figure Bushings Control Power Cover HarnessesServicing Control Panel Panel ScrewsAccessing Imaging Unit Viewing ScreenServicing Flame Pennants Screw Fan Assembly Posts for Blade ConnectorsServicing Fan Blower Base CoverLocating Flame Pennants Reassemble imager. See Accessing Replacing Lamp FixturesReplacing Reflective Ribbons Cleaning Viewing ScreenAccessing Imaging Unit For Replacement Remove any loose or damaged ribbon materialParts Under Warranty Technical ServiceReplacement Parts Parts Not Under WarrantyAccessories Illustrated Parts Breakdown Parts List 39/40 114275-01 Wire Tie 111066-01 Control Panel Decal 111066-03 Keep this Warranty Warranty InformationLimited 1 Year Warranty