Avalon Stoves Indoor Fireplace manual 0Installation

Page 10

1 0Installation

Clearances

Insert must be placed so that no combustibles are within, or can swing within (e.g. drapes, doors), 36" of the front of the heater.

Insert must be placed a minimum 8-3/4" from a side wall (or combustible protruding more than 3/4").

Mantel Requirements

The mantel must meet the requirements shown in the illustration to the right.

12”

The mantel must fall within this shaded area (or above). Maximum mantel depth is 12”.

Hearth Requirements

The non-combustible hearth must extend 6” to the front and sides of the firebox opening (you must open the door to measure).

Facing Requirements

38”

The non-combustible facing must extend 7" to the side and 6" above the hopper lid.

Placing the Insert

The insert must be placed within an undamaged masonry or factory built (metal) fireplace. Loose bricks or other damage must

be fixed. Clean the fireplace before installing.

3-1/2”

33”

Side Wall

Min. 8-3/4"

Apply the "This fireplace has been altered..." sticker to the fireplace. You may wish to place it in a location where it will be covered by the surround panels.

The vent should be routed to the fireplace prior to installing the insert. See the section "Vent Installation" for details on vent location.

Use the leveling bolts for fireplaces with recessed floors (included with the insert). Screw them into the baseplate from below.

13-1/4"

Place the insert so the back edge of the baseplete extends 13-1/4" into the fireplace.

Run the power cord to the side along the front of the fireplace (do not route it under the insert).

Travis Industries

4 0 5 0 5 2 5

1 0 0 - 0 1 1 4 4

Image 10
Contents Astoria Bay Pellet Insert Introduction Important Information 2IntroductionTravis Industries 5 0 5 2 0 0 1 1 4 Table of Contents Safety Precautions Mobile Home 6Specifications Installation7 8Installation Hopper Extension Set-upInstallation9 Re-install the hopper walls following the directions below0Installation Installation1 Venting the Pellet StoveMobile Home Requirements 2InstallationOutside Air used for combustion Baffle Installation Restrictor Adjustment4Installation Surround Panel & Circuit Board InstallationInstallation into a Masonry Fireplace Hint6Installation Installation into a Factory Built Metal FireplaceLocation of Controls Safety NoticeOperation1 Starting the Heater for the First TimeLoading Pellets 8OperationTwo Modes of Operation To Start Manual ModeTo Adjust the Heat To Shut DownTo Adjust Room Temperature or Start the Stove Auto Mode0Operation Adjusting the Fan Speed Operation2Start-Up Sequence Maintenance Required Light2Operation Auger on LightUsing a Pellet/Corn Mix with This Heater Power OutagesManual Auger Button Inspect the Burn 4MaintenanceDaily Maintenance whenever using the heater Make Sure Pellets are Not Piling UpCleaning the Firepot Maintenance2Check Firepot for Clinkers 6Maintenance Opening The DoorClean the Heat Exchange Tubes Weekly Maintenance or every 5 bags of pelletsClean the Hopper Cleaning the Optional Plated SurfacesClean the Glass 8MaintenanceCheck Baffles, Ashbox, Ashpan, Dispose Ash If Necessary Remove the ashbox prior to conducting the service below Sweep Ash Into Ashpan0Maintenance Yearly Maintenance or every tonMaintenance3 Clean the Vent make sure the heater and vent is coolDoor Seal 2MaintenanceDoor Alignment Adjusting the Door Hinge and Latch Hinge AdjustmentReplacement Parts Check for Air Leaks Around the Door, Glass, and AshpanNormal Operating Sounds Covection FanSafety Label Serial NoLimited 7 Year Warranty Years 1 & 2 Coverage Parts & Labor8Optional Equipment ThermostatOptional Equipment ZC Kit 9 9 2 0 0 1 40Index

Indoor Fireplace specifications

The Avalon Stoves Indoor Fireplace is a remarkable addition to any home, offering the perfect blend of aesthetics, functionality, and efficiency. Designed with a focus on both beauty and performance, this fireplace redefines the indoor heating experience while enhancing the ambiance of any living space.

One of the standout features of the Avalon Stoves Indoor Fireplace is its clean and contemporary design. Available in various styles and finishes, it fits seamlessly into diverse interior décors, from modern to rustic. The large glass viewing panel provides an expansive view of the flames, allowing users to enjoy the mesmerizing fire while adding warmth to the room.

Energy efficiency is at the heart of Avalon’s design philosophy. The fireplace is equipped with advanced combustion technology that maximizes burn efficiency, ensuring that more heat is extracted from the fuel. This leads to reduced fuel consumption and lower heating costs, making it an environmentally friendly choice. Some models feature a secondary combustion system, which allows the fireplace to burn cleaner, producing fewer emissions and adhering to stringent environmental regulations.

Another significant characteristic of the Avalon Stoves Indoor Fireplace is its versatility in fuel options. Homeowners can choose from traditional wood-burning models or the more contemporary propane and natural gas variants. This flexibility allows users to select the most suitable fuel source for their needs and preferences. The easy-to-use ignition systems further enhance the convenience of starting and maintaining the fire.

Safety features are paramount in the design of Avalon fireplaces. With options for air wash systems that keep the glass clean and cooling features to prevent overheating, users can enjoy a cozy fire with peace of mind. The construction materials are selected for their durability and heat resistance, ensuring that the fireplace stands the test of time.

In summary, the Avalon Stoves Indoor Fireplace combines an elegant design with advanced technology and safety features. Its energy efficiency, versatility in fuel options, and stylish appearance make it a top choice for those looking to add warmth and charm to their home. Whether for heating or simply enjoying the beauty of fire, Avalon offers a fireplace solution that meets modern lifestyles while providing a timeless appeal.