PGS TC36 AR manual Wall Shield Thimble TCVT.THIMA, Insulated Collar Shield, Vent pipe

Page 12

Vent pipe:

Install vent pipe through the wall thimble and attach to fl ue outlet collar on top of the fireplace. Secure all joints with screws and seal with approved "High Temp." self-adhesive aluminum tape provided (see VENT PIPE SEALANT section).

The fireplace position may need to be adjusted to ensure that the vent pipe does not protrude beyond the outer wall or be recessed any more than 12 inches with the inner pipe.

Fig. #16

WALL SHIELD

THIMBLE

TCVT.THIMA

Wall vent terminal:

1)Engage the 8" vent collar with the vent pipe and slide terminal into place. Attach the terminal to the outside wall. The vent terminal must not be recessed into the exterior wall or siding.

2)Caulk in place to prevent any moisture entering the build- ing.

NOTE: MINIMUM CLEARANCES TO THE VENT TERMINAL MUST BE MAINTAINED (see Fig. #17).

14 1/2" FRAMED OPENING

ELBOW

	TCVT.811XLB90	HORIZONTAL
	TCVT.811XLB90	TERMINAL
		TERMINAL
	24" VENT PIPE	TCVT.9360
	24" VENT PIPE
	TCVT.811X24

INSULATED

COLLAR

SHIELD

TC36.9709

12" VENT PIPE	*
TCVT.811X12

* Minimum height from the floor to center of the opening with a maximum horizontal run of 18" using TC Vent. The height will need to be increased with a longer horizontal run .

12 36ARB2

050505-36

Image 12

Contents Installation Operating Instructions What to do if YOU Smell GASContents Safety Fireplace DimensionsMantel Clearance Chart CeilingMantel Mantel ClearanceInstallation Requirements TOP StandoffsLocating the Fireplace Dimensions Steel Stud Framing KITTC36.BFRKITA Framing and FinishingInstallation Detail Concrete BoardReconnect Pilot Flame indicator wiring and reinstall Control BOXHearth Extension Window FrameControl BOX Location Framing Detail Not OverVenting Exterior wall openingWall Thimble and Vent Must not Protrude Beyond Siding Wall thimbleTrim to Length Wall Shield Thimble TCVT.THIMA Insulated Collar ShieldVent pipe Wall vent terminalWall Roof Termination Roof Termination Venting Vent Pipe Roof Support BracketCeiling opening Ceiling firestopVertical Termination CAP Vent Pipe Mastic Storm CollarRoof vent terminal Vent Terminal Minimum Clearances Vent Terminal ClearanceVent Terminal Minimum Clearances to Adjacent Structures Vent Pipe Sealant Vent Pipe SealantInsulated Collar Shield Be USED. see Section BelowWall and Roof TerminationRestrictor PositionOptional Wall Switch Manual Millivolt ValveGAS Supply Max. LengthWindow Frame Removal Firebox Panels Installation Herringbone Panel SET ShownHerringbone Heritage REDFor Your Safety Read Before Lighting Lighting InstructionsTo Turn OFF GAS to Appliance First FireHI-LO Flame Adjustment Wall Thermostat Canada Only Optional GASC.THERMOExtend Shutdown Maintenance Millivolt PilotElectronic Pilot Replacement Parts DescriptionReplacement PARTS-MILLIVOLT Control Assembly Pilot Assembly NGReplacement Parts Electronic Control Assembly ELECTRONIC, Wire HarnessElectronic Valve Wiring Diagram Fig. #Wall Termination KIT Roof Termination KIT Vent Pipe Dimensions Pipe 10 1/4 16 1/4 10 15/16 22 1/4 46 1/4Pipe 23 1/4 27 5/8 PipeFlexible Connector With Shutoff Valve Various GAS Supply ConnectionsGastitetm Flex Line with Reducing Coupling Black Iron Pipe with UnionSafety Label Location For USE with Natural GAS LP GASEN Case D’EMPLOI Avec Made in CanadaAllenby Rd., Duncan, BC V9L Phone