Regency P48-LP, P48-NG Installing the Optional FAN, To Remove the Fan, Shut the power off

Page 33

INSTALLATION

INSTALLING THE OPTIONAL FAN

120 Volt AC power is needed for the fan switch and blower. The fan can be hard wired if desired. The receptacle box should be installed on the left hand side of the unit by a qualified electrician. The neutral (wider) slot of the po- larized receptacle should be at the top.

Unit must be grounded at all times. Do not cut the ground terminal off under any circumstances.

9)Attach the two control boxes to the bottom louver and tighten the 2 screws on the left side and 2 screws on the right side.

1)Shut the power off.

2)Remove the standard flush door and the optional bay door, if installed. Open the bottom louver door.

3)Remove the 2 screws holding the Burner ON/OFF switch and bracket to the bottom louver and lift the assembly out.

4)Turn the fan base on its side (with the base facing towards you) and then slide the fan in towards the rear of the unit. Turn the fan upright and slip it over the two mounting studs. Take care not to damage the insula- tion on the fan base. Ensure that the fan blades do not rub against the valve tubing. Diagram 1.

5)Connect fan ground cable to ground lug. Refer to wiring diagram.

6)Slide the thermodisc/cover assembly into the bracket clip on the underside of the firebox. Check that no wire will touch the hot surfaces. Diagram 2.

7)Attach the Fan control box to the Burner ON/ OFF control box. Diagram 3.

Diagram 1

Diagram 2

Diagram 3: Use the clip & hook on the side of the control boxes to join them together.

8)Secure the two boxes together with one screw.

Secure the 2 boxes together

with one screw.

Secure left side with 2 screws.

Secure right side with 2 screws.

10)Secure the fan wires and power cord by attaching one of the adhesive backed wire holder clips (Part #910-199) onto the stove base. Use the second clip to bundle up the wires approximately 4" from the control box. Ensure that there is no interference with the wires when the louver is closed and that no wire will touch the hot metal surfaces or sharp edges.

11)Plug the fan power cord into the rear end of the receptacle box to provide the maximum clearance from the louvers.

To Remove the Fan

1)Shut the power off.

2)Reverse the above instructions.

NOTE: The bearings are lubricated for life. Do not lubricate them. Make sure you vacuum the fan area on a regular basis.

IMPORTANT:

These fans collect a lot of dust from within your home. Ensure you maintain these fan motors on a regular basis by vacuuming out the fan blades and hous- ing using a soft brush nozzle.

Regency P48 Zero Clearance Direct Vent Gas Fireplace

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents P48 Gas Fireplace Regency P48 Zero Clearance Direct Vent Gas Fireplace To the New OwnerTable of Contents Tiquetteé Pasne Cetteenlever Thisremove /LABEL Safety LabelGeneral Safety Information InstallationInstallation Checklist Save These InstructionsManufactured Mobile Home Additional Requirements Unit Specifications Locating Your GAS StoveOptional Duct System Optional Heat ReleaseMantel ClearancesCeiling Max. Depth 36 914mmMantel LEG Clearances MantelsFraming & Finishing Top Standoff Assembly Unit Assembly Prior to InstallationVenting Introduction Top Facing Support Side Nailing StripsAir supply outlet VentRegency Direct Vent System Flex Horizontal Terminations Only VentingSimpson DURA-VENT Venting Components List Simpson DURA-VENT VentingDescription Parts not supplied by Dura-VentRegency Direct Vent System Flex Venting Arrangements Horizontal TerminationsHorizontal Venting with Three 3 90o Elbows Horizontal Venting with Two 2 90o ElbowsMin Max Min Max Min Max Vertical Venting with Two 2 90o ElbowsOption + H1 V + Vertical Venting with Three 3 90o ElbowsSimpson DURA-VENT Direct Vent GS System Venting Arrangements Vertical TerminationsInstallation Horizontal Installations Vertical Termination Offset ChartFor Regency Direct Vent System Flex Installation ProceduresPilot Adjustment GAS Line InstallationGAS Pipe Pressure Testing High ElevationBottom Clips Brick Panels Installation02-88 02-90 02-87 02-89 02-86 02-85 02-84 02-83 LOG SET Installation02-88 02-83 02-86 02-85 02-89 02-84 02-8902-90 02-8602-84 02-87 02-88 02-8502-83Standard Flush Door Flush LouversNot under the gas line Optional BAY Door BAY LouversOptional Bay Trim Double Screen Door Optional Finishing TrimThermostat Wire Table Option Remote ControlDo not cut the ground terminal off under any circumstances Wiring DiagramInstalling the Optional FAN Shut the power offTo Remove the Fan Conversion Kit Contains Operating Instructions Copy of the Lighting Plate Instructions Normal Operating Sounds GAS AppliancesMaintenance Installing Valve Bay Glass ReplacementDoor Glass Shut off the gas supply Removing ValveP48 Main Assembly Parts List102 100 P48 Burner & LOG Assembly P48 Flush Door & Louvers P48 BAY Front & Louvers Regency P48 Zero Clearance Direct Vent Gas Fireplace Regency P48 Zero Clearance Direct Vent Gas Fireplace Conditions WarrantyInstaller Please complete the following information

P48-NG, P48-LP specifications

The Regency P48-NG and P48-LP are notable entrants in the world of propane heating solutions, designed to meet the needs of both residential and commercial users. These high-efficiency models combine modern technology with user-friendly features, making them a popular choice for those looking to enhance their heating systems.

One of the standout features of the P48-NG and P48-LP is their powerful heating capacity. Both models are engineered to deliver consistent warmth, effectively heating spaces of various sizes. The P48-NG operates efficiently on natural gas, while the P48-LP is designed for use with liquid propane, providing versatility depending on available fuel sources. Suitable for a wide range of applications, these models can easily accommodate homes, workshops, and even larger commercial spaces.

In terms of technology, the Regency P48 series employs advanced burner systems to optimize combustion and maximize energy efficiency. This ensures that users experience lower energy bills while also reducing their carbon footprint. The units also feature a patented air mixing system that contributes to cleaner burning and improved airflow, resulting in a more comfortable and uniform heat distribution throughout the space.

Another significant characteristic of the P48-NG and P48-LP is their remarkable design. The models boast a sleek, contemporary appearance that fits seamlessly into a variety of decors, from rustic to modern. The large viewing area offers an impressive flame presentation, creating a mesmerizing ambiance that enhances the living space.

Additionally, safety features are paramount in the design of the Regency P48 series. Both models include advanced safety controls, such as an automatic shut-off system in the event of gas leaks or operational anomalies, ensuring peace of mind for users. The installation of these units is straightforward, and they comply with current safety standards, making them a reliable choice for any environment.

The P48-NG and P48-LP also incorporate user-friendly controls that allow for easy temperature adjustments. Remote control options are available, adding convenience for users who wish to manage their heating system from a distance. With all these features combined, the Regency P48-NG and P48-LP are innovative heating solutions that embody efficiency, safety, and style, catering to the modern heating needs of today’s users.
Top Page Image Contents