Lopi Leyden Pellet Stove manual 6Specifications

Page 6

6Specifications

Heating Specifications

Approximate Maximum Heating Capacity (in square feet)*

800 to 2,250 Sq. Feet

Burn Rate (Pounds per Hour)**

1.7 to 5.5

Maximum Burn Time on Low Burn**

29 Hours

Hopper Capacity

50 Pounds

*Heating capacity will vary depending on the home's floor plan, degree of insulation, and the outside temperature. It is alsoaffected by the fuel size, quality, and moisture level.

**Small pellets will increase or decrease the stated burn rates and burn times. Differences of plus or minus 20% depending on fuel quality may occur.

Dimensions

25"

27-3/4"

Weight: 390 Lbs.

27-1/4"

7-3/4"

17-1/4"

4" Diameter

Exhaust

27"

NOTE:

Measure front and side clearances from the stove top. Rear and corner clearances are measured from the stove body.

Electrical Specifications

Electrical Rating

115 Volts, 3.6 Amps, 60 Hz

Watts During Start-Up Sequence

400 (approximately)

Watts During Operation

180 (approximately)

Fuel

 

This heater is designed and approved for pelletized wood fuel or a mixture up to 50% corn, 50% pellets. See page 26 for details on using a corn pellet mix.

EPA Compliance

This heater has been tested exempt from EPA Phase II Requirements by OMNI-Test Laboratories, Inc.

Travis Industries

4061016

1 0 0 - 0 1 1 8 4

Image 6
Contents Leyden Important Information 2IntroductionIntroduction Travis IndustriesTable of Contents 4Safety Precautions Safety Precautions Mobile Home6Specifications Stove Placement Installation OptionsPlanning The Installation Before You BeginClearances Straight Installation InstallationClearances Corner Venting the Pellet Stove Maximum Venting DistanceInstalling the Pellet Vent Pellet Vent TypePellet Vent Termination Mobile Home Requirements Outside Air used for combustionRestrictor Adjustment Alcove Installation RequirementsBaffle Installation Door Seal VerificationThermostat Installation Installation Example Direct Through-the-wall Installation Installation Example Interior Vertical Installation Min Ceiling Support / Fire Stop Spacer VentInstallation Example Class a Chimney Retrofit Installation Example Masonry Fireplace Hearth Stove Vertical Cap Cover Plate non-combustible Storm Collar Installation Example Freestanding Masonry Chimney Vent Flex SectionLocation of Controls Safety Notice0Operation Starting the Heater for the First TimeOperation2 Loading PelletsTwo Modes of Operation 2Operation Manual ModeTo Adjust the Heat To StartAuto Mode To Adjust Room Temperature or Start the StoveAdjusting the Fan Speed 4OperationStart-Up Sequence Fault LightPower Outages Manual Auger ButtonUsing a Pellet/Corn Mix with This Heater 6OperationInspect the Burn Maintenance2Daily Maintenance whenever using the stove Make Sure Pellets are Not Piling Up8Maintenance Cleaning the FirepotCheck Firepot for Clinkers Door Opening 2Maintenance Bi-Weekly Maintenance or every 10 bags of pelletsMaintenance3 Bi-Weekly Maintenance or every 10 bags of pelletsClean the Baffles Sweep Ash Into Ashpan Clean the Glass Check Ashpan, Dispose if necessary4Maintenance Yearly Maintenance or every two tonsClean the Vertical Exhaust Duct Maintenance3 6Maintenance Clean the Exhaust BlowerAdjusting the Door Hinge and Latch Clean the Convection BlowerClean the Vent Check for Air Leaks Around the Door, Glass, and AshpanReplacement Parts Door ReplacementReplacement Parts Normal Operating Sounds Convection FanSafety Label Limited 7 Year Warranty Years 1 & 2 Coverage Parts & Labor2Index