Regency P121 Unit Assembly Prior to Installation, Venting Introduction, Top Standoff Assembly

Page 12

INSTALLATION

Facing & Finishing Requirements

This fi replace is supplied with a 3" metal extension trim above the fi replace. The extension trim may be replaced if the framing is faced with a non- combustible material placed fl ush with the front and side face of the unit and extending from the top of the unit. (ie. tile, slate, etc.)

UNIT ASSEMBLY

PRIOR TO

INSTALLATION

The 4 Top Standoffs must be correctly positioned and attached to the top before unit is slipped into position.

Top Standoff Assembly

The top standoffs are shipped in a fl at position and must be folded into shape and attached.

1) Remove the standoffs from the fi replace top.

2) Take each standoff and bend into the correct shape. Bend up at the bend lines until the screw holes in the standoff and the pre- punched screw holes on the fi replace top line up.

3) Attach the standoff securely to the top with 4 screws per standoff (on opposite corners).

VENTING

INTRODUCTION

The P121-2/P121LC-2/P121RC-2/P131-2 uses the "balanced flue" technologyCo-Axialsystem. The inner liner vents products of combustion to the outside while the outer liner draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air up the chimney.

Note: These flue pipes must not be

connected to any other appliance.

The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systemsareprohibited.(See"RigidPipeVenting Systems" for more details and exceptions).

12

Regency® P121-2/P121LC-2/P121RC-2/P131-2 Zero Clearance Direct Vent Gas Fireplace

Image 12
Contents P121 / P121LC / P121RC / P131 Manufactured Mobile Home Requirements To the New OwnerTable of Contents Safety Label Copy of Safety Decal for P121/P121LC/P121RC/P131Requirements MA Code CO DetectorInstallation General Safety InformationInstallation Checklist Important Message Save These InstructionsSpecifications Non-load bearingP121LC-2 Left Corner Unit Locating Your GAS Fireplace Locations see section Exterior Vent Termination LocationsClearances Combustible MantelsFraming Dimensions Framing and FinishingP121-2 See Thru P131-2 Pier Corner UnitUnit Assembly Prior to Installation Top Standoff AssemblyVenting Introduction Exterior Vent Termination Locations VentHeight Meters Minimum Feet RoofPitchRigid Pipe Venting Components List SV4LB6Venting Arrangement Horizontal Terminations Rigid Pipe Venting Systems Horizontal or Vertical TerminationsRigid Pipe Venting Arrangements Horizontal Terminations Regency Direct Vent System Flex Propane & Natural GasHorizontal Venting with Two 2 90o Elbows Horizontal Venting with Three 3 90o ElbowsRigid Pipe Venting Arrangements Vertical Terminations Propane & Natural GasVertical Venting with Two 2 90o Elbows Vertical Venting with Three 3 90o ElbowsSet the unit in its desired location. Check This allows for small adjustments Vertical TerminationsInstallation Procedures Offset ChartFor Regency AstroCapTM Direct Vent System Flex Conversion KIT #731-969 from NG to LP LPG Conversion Kit Contains QtyInstallation of the DC Sparker Ground Wire from Kit Pilot Adjustment GAS Line InstallationGAS Pipe Pressure Testing High ElevationLOG Installation 327 329 326 328327 Finishing Trim Louvers & GrillsP121-2 & P131-2 Corner Models Thermostat Wire Table Diagram belowWiring Diagrams Do not cut the ground terminal off under any circumstancesFor Propane Units and Units Equipped with DC Spark Boxes Terminal Block LocationShutdown Procedure First Fire Aeration AdjustmentLighting Procedure Operating InstructionsNormal Operating Sounds of GAS Appliances Copy of the Lighting Plate InstructionsMaintenance Removing Valve Remove Left & Right Side Base Brick PanelsInstalling Valve FAN ReplacementParts List P121-2 see Thru Main AssemblyDescription P131-2 Pier Main Assembly P121RC-2 Right Corner Main Assembly 204 225P121LC-2 Left Corner Main Assembly P121/P121LC/P121RC/P131-2 Burner Assembly & LOG SET Page Page Page Warranty ConditionsInstaller Please complete the following information
Related manuals
Manual 40 pages 33.79 Kb

P121LC, P121, P121RC, P131 specifications

The Regency P121RC, P121, P131, and P121LC are advanced technological innovations in the realm of heating, ventilation, and air conditioning (HVAC) systems. Designed for both residential and commercial applications, these models are known for their efficiency, reliability, and comfort-enhancing features.

The Regency P121RC is particularly notable for its high-efficiency rating, making it a popular choice for environmentally conscious consumers. With advanced heat pump technology, it provides optimal heating and cooling throughout the year, reducing energy consumption while maintaining a consistent indoor climate. The use of environmentally friendly refrigerants further emphasizes its commitment to sustainability.

The P121 model stands out for its cutting-edge smart technology integration. It is equipped with Wi-Fi connectivity, allowing users to control their HVAC systems remotely via a mobile application. This feature not only enhances convenience but also enables energy management, reducing operational costs through effective scheduling and monitoring.

The P131 model caters to larger spaces, thanks to its robust cooling and heating capabilities. It employs a variable-speed compressor that adjusts to the specific demands of the space, ensuring optimal performance while minimizing noise disruption. This model is also compatible with smart home systems, contributing to a seamless integration of technology within modern living environments.

Meanwhile, the P121LC is designed with energy conservation in mind, featuring a dual-stage heating and cooling system. Its advanced airflow technology ensures even distribution of temperature, promoting overall comfort and reducing the risk of hot or cold spots in a room. Like its counterparts, it supports remote operation through smart technology, offering users full control over their indoor climate.

In terms of construction, these models prioritize durability and longevity. They feature robust insulation and high-quality materials, which contribute to their energy efficiency and operational lifespan. The compact design also allows for flexible installation options, making them suitable for various types of spaces.

Overall, the Regency P121RC, P121, P131, and P121LC represent the pinnacle of modern HVAC technology, blending efficiency, innovative features, and user-friendly control options to provide optimal comfort in any setting. As homeowners and businesses increasingly prioritize sustainability and energy management, these models are set to play a vital role in achieving a more comfortable and eco-friendly future.