Regency P33-LP4 Flush Louvers, Double Screen Door, Optional BAY Trim, Optional BAY Door

Page 33

INSTALLATION

FLUSH LOUVERS

1)Install the top louver by sliding the two bracket clips into the brackets located underneath the top of the fi rebox.

2)Install the bottom louver by folding the louver down and then sliding the Bottom Louver bracket down onto the 2 pins on the base of the unit (Diagram1). Secure with 1 screw (Diagram 2).

Diagram 1

Diagram 2

DOUBLE SCREEN

DOOR

1)Pull out the top louver.

2)Center the screen door and hook over the fl ush door.

Note: Top and bottom louvers are different.

3)Open the bottom louver. Pull the Burner ON/OFF control box from inside the bottom of the fi replace and position the slots in the bracket over the 2 screws on the left side of the bottom louver. Push down to lock into place. Tighten the screws.

3)Open the screen door(s) and secure the screen door to the fl ush door front with 2 clips on the bottom left and right side.

Clip locations

Clip installed on right side.

Note: If any maintenance etc. must be done in the firebox, first remove the Bay louvers and door.

OPTIONAL BAY TRIM

Attach the 4 supplied magnets, each to the back of the top and bottom trim pieces (space out evenly) and attach trim to the top and bot- tom of Bay door.

OPTIONAL BAY DOOR

The Bay louvers MUST be used

with the Bay glass option.

 

 

The optional Bay door is an overlay on the

 

 

flush front. The standard fl ush door and glass

Screws on

Burner ON/OFF

must remain on the unit.

 

louver bracket

1) Hook the top of the bay door over the fl ush

control box

 

 

door fl ange and swing the bottom against

 

 

the bottom fl ange of the fl ush door.

 

 

2) Secure to the fl ush door bottom bracket with

 

 

2 screws provided.

Burner ON/OFF control box attached to

bottom fl ush louver.

Regency® P33-4 Zero Clearance Direct Vent Gas Fireplace

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents P33-4 Zero Clearance To the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Safety Label Safety LabelFor the State of Massachusetts only RequirementsGeneral Safety Information InstallationImportant Message Before YOU StartUnit Dimensions Installation ChecklistLocating Your Fireplace Duct System OptionMantel LEG Clearances ClearancesFraming and Finishing Vertical Termination or Vertical Rise with HorizontalRear Termination Top Standoff Assembly Unit Assembly Prior to InstallationVenting Introduction Top Facing Support Side Nailing Strips= Clearance to permanently closed window *min /30cm Exterior Vent Termination LocationsHorizontal Terminations Only Regency Direct Vent Flex SystemAlternate Without any joints or seamsInstallation Procedures For Regency Direct Vent System FlexMinimum and Maximum Vent Clearances Vent Length Flat Wall InstallationThickness inches Required inches Max. WallDescription 6-5/8 Rigid Pipe Cross Reference Chart6-5/8 Rigid Pipe Cross Reference Chart Vertical Terminations Propane & Natural Gas Rigid Pipe Venting ArrangementsInstallation Regency Direct Vent System Flex Option + H1 Horizontal Venting with Two 2 90o ElbowsOption +H1+H2 Option +H1Vertical Venting with Two 2 90o Elbows Horizontal Venting with Three 3 90o ElbowsOption +V1 +H1 Option +V1Vertical Venting with Three 3 90o Elbows Required Parts Vertical Termination With CO-LINEAR Flex SystemDescription Alternate Approved CapsHorizontal Distance Feet Venting Arrangements Vertical TerminationsSnorkel Terminations Unit Installation with Horizontal TerminationUnit Installation With Vertical Termination GAS Line InstallationThis allows for small adjustments GAS Pipe Pressure Testing Pilot AdjustmentHigh Elevation T. Valve DescriptionConversion KIT# 434-969 from NG to LP For P33-4/H25-1 Using SIT 820 Nova Gas ValveGlow on logs Installation of the DC Sparker for the P33-4 Unit Only 251 250Optional Flush Trim Standard Flush DoorCutout 5th Grate TabDouble Screen Door Flush LouversOptional BAY Trim Optional BAY DoorFlush Louver Top Heat Shield BAY LouversBay Louver Top Heat Shield Burner ON/OFF Control boxFull Screen Doors Cut-Out Oblong Hole Top Flange BottomCut-Outs Top Grill Hinge Location Bottom GrillWall Switch Remote ControlThermostat Wire Table Wall ThermostatDo not cut the ground terminal off under any circumstances Wiring DiagramsFor Propane Units and Units Equipped with DC Spark Boxes Secure the 2 boxes together With one screw Installing the Optional FANCopy of the Lighting Plate Instructions Operating InstructionsShutdown Procedure Lighting ProcedureAeration Adjustment Operating InstructionsNormal Operating Sounds Maintenance MaintenanceLOG Replacement GAS AppliancesBay Glass Replacement Flush Glass ReplacementThermopile Thermocouple Glass GasketDiagram 3 Lift out Valve Tray Assembly Installing ValveDiagram 2 Rear Log Stand & Valve Tray Assembly Removing ValveParts List Main AssemblyDescription Parts List Part Description Burner & LOG AssemblyFlush Front & Louvers BAY Front & Louvers Conditions WarrantyInstaller Please complete the following information

P33-LP4 specifications

Regency P33-LP4 is an innovative and versatile propane gas fireplace designed to provide both warmth and ambiance while enhancing the aesthetic appeal of any living space. This model stands out for its combination of modern technology, functionality, and elegance, making it a popular choice among homeowners seeking an efficient heating solution without sacrificing style.

One of the key features of the P33-LP4 is its contemporary design. The fireplace presents a sleek, minimalist look that integrates seamlessly into both traditional and modern interiors. It offers a range of finishing options, including various trims and glass fronts, allowing homeowners to tailor the appearance of the fireplace to their personal taste and existing decor.

A hallmark of the Regency P33-LP4 is its advanced heating capabilities. With a powerful output of up to 33,000 BTUs, this fireplace can efficiently heat spaces of different sizes, making it suitable for both small cozy rooms and larger open areas. The unit also features a high-efficiency burner that maximizes heat production while reducing fuel consumption, which is ideal for energy-conscious users.

In terms of technology, the P33-LP4 boasts a user-friendly electronic ignition system that ensures reliable startups, even in colder temperatures. The fireplace can be controlled through a convenient remote or a wall switch, allowing users to adjust the flame height and heat settings with ease. Additionally, the unit incorporates a fan that circulates warm air throughout the room, enhancing overall heating efficiency and comfort.

Safety is paramount in the design of the Regency P33-LP4. The fireplace is equipped with a built-in safety shut-off feature that automatically turns off the gas supply in case of an unexpected accident. Moreover, the glass front remains cool to the touch, reducing the risk of burns and making it family-friendly.

Flexibility is another advantage of the P33-LP4, as it can be installed in various configurations, including as a built-in unit or a freestanding fireplace. The options for installation enable homeowners to create a unique focal point in their living space, adapting to different architectural layouts.

In conclusion, the Regency P33-LP4 combines contemporary design, efficient heating technology, and safety features, making it an excellent choice for those seeking a stylish and functional propane fireplace. Its versatility and reliability enhance the home environment while providing a warm and inviting atmosphere for family and guests.
Top Page Image Contents