Regency P33-LP4 Full Screen Doors, Cut-Out Oblong Hole Top Flange Bottom, Cut-Outs

Page 35

INSTALLATION

FULL SCREEN DOORS

1)Before beginning the installation, remove the Glass Door from the unit. Refer to the manual for instructions.

2)Slide the Bottom Faceplate Bracket into the bottom of the unit, secure it into the pins located on the inside of the fi re box. Once the bracket is in place, tighten the screws into the hinges on the left and right sides.

BottomFaceplate

Bracket

Pin location

4)a) Before attaching the Full Screen Door Frame to the unit, loosen the left and right side #8 Self Tapping Philips screws located on the inside top of the outer frame of the appliance. Also remove the center screw.

b)Slide the cut-outs in the Top and Bottom Flange of the Full Screen Door Frame under the screw heads which were loosened in step 4a). Once the Frame is in place, tighten the screws to secure. Also re-secure the top center screw through the oblong hole.

Full Screen Door

Frame

Faceplate

Screw

Mounting

Bracket

 

3)Before attaching the Full Screen Door Frame, remove the Screen Doors from the Full Screen Door Frame by fully opening the doors and lifting up off of the hinges. See important note in step 10.

Cut-Out

Oblong Hole

Cut-Out

Top

Flange

Bottom

Backside of FullFlange

Screen Door

Frame Shown

Cut-Outs

Regency® P33-4 Zero Clearance Direct Vent Gas Fireplace

35

Image 35
Contents P33-4 Zero Clearance To the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Safety Label Safety LabelFor the State of Massachusetts only RequirementsBefore YOU Start InstallationGeneral Safety Information Important MessageDuct System Option Installation ChecklistUnit Dimensions Locating Your FireplaceMantel LEG Clearances ClearancesRear Termination Framing and FinishingVertical Termination or Vertical Rise with Horizontal Top Facing Support Side Nailing Strips Unit Assembly Prior to InstallationTop Standoff Assembly Venting Introduction= Clearance to permanently closed window *min /30cm Exterior Vent Termination LocationsWithout any joints or seams Regency Direct Vent Flex SystemHorizontal Terminations Only AlternateMinimum and Maximum Vent Clearances Installation ProceduresFor Regency Direct Vent System Flex Max. Wall Flat Wall InstallationVent Length Thickness inches Required inchesDescription 6-5/8 Rigid Pipe Cross Reference Chart6-5/8 Rigid Pipe Cross Reference Chart Vertical Terminations Propane & Natural Gas Rigid Pipe Venting ArrangementsInstallation Regency Direct Vent System Flex Option +H1 Horizontal Venting with Two 2 90o ElbowsOption + H1 Option +H1+H2Option +V1 Horizontal Venting with Three 3 90o ElbowsVertical Venting with Two 2 90o Elbows Option +V1 +H1Vertical Venting with Three 3 90o Elbows Alternate Approved Caps Vertical Termination With CO-LINEAR Flex SystemRequired Parts DescriptionHorizontal Distance Feet Venting Arrangements Vertical TerminationsSnorkel Terminations Unit Installation with Horizontal TerminationThis allows for small adjustments Unit Installation With Vertical TerminationGAS Line Installation T. Valve Description Pilot AdjustmentGAS Pipe Pressure Testing High ElevationConversion KIT# 434-969 from NG to LP For P33-4/H25-1 Using SIT 820 Nova Gas ValveGlow on logs Installation of the DC Sparker for the P33-4 Unit Only 251 2505th Grate Tab Standard Flush DoorOptional Flush Trim CutoutOptional BAY Door Flush LouversDouble Screen Door Optional BAY TrimBurner ON/OFF Control box BAY LouversFlush Louver Top Heat Shield Bay Louver Top Heat ShieldCut-Outs Full Screen DoorsCut-Out Oblong Hole Top Flange Bottom Top Grill Hinge Location Bottom GrillWall Thermostat Remote ControlWall Switch Thermostat Wire TableDo not cut the ground terminal off under any circumstances Wiring DiagramsFor Propane Units and Units Equipped with DC Spark Boxes Secure the 2 boxes together With one screw Installing the Optional FANCopy of the Lighting Plate Instructions Operating InstructionsOperating Instructions Lighting ProcedureShutdown Procedure Aeration AdjustmentGAS Appliances MaintenanceNormal Operating Sounds Maintenance LOG ReplacementGlass Gasket Flush Glass ReplacementBay Glass Replacement Thermopile ThermocoupleRemoving Valve Installing ValveDiagram 3 Lift out Valve Tray Assembly Diagram 2 Rear Log Stand & Valve Tray AssemblyDescription Parts ListMain Assembly Parts List Part Description Burner & LOG AssemblyFlush Front & Louvers BAY Front & Louvers Conditions WarrantyInstaller Please complete the following information

P33-LP4 specifications

Regency P33-LP4 is an innovative and versatile propane gas fireplace designed to provide both warmth and ambiance while enhancing the aesthetic appeal of any living space. This model stands out for its combination of modern technology, functionality, and elegance, making it a popular choice among homeowners seeking an efficient heating solution without sacrificing style.

One of the key features of the P33-LP4 is its contemporary design. The fireplace presents a sleek, minimalist look that integrates seamlessly into both traditional and modern interiors. It offers a range of finishing options, including various trims and glass fronts, allowing homeowners to tailor the appearance of the fireplace to their personal taste and existing decor.

A hallmark of the Regency P33-LP4 is its advanced heating capabilities. With a powerful output of up to 33,000 BTUs, this fireplace can efficiently heat spaces of different sizes, making it suitable for both small cozy rooms and larger open areas. The unit also features a high-efficiency burner that maximizes heat production while reducing fuel consumption, which is ideal for energy-conscious users.

In terms of technology, the P33-LP4 boasts a user-friendly electronic ignition system that ensures reliable startups, even in colder temperatures. The fireplace can be controlled through a convenient remote or a wall switch, allowing users to adjust the flame height and heat settings with ease. Additionally, the unit incorporates a fan that circulates warm air throughout the room, enhancing overall heating efficiency and comfort.

Safety is paramount in the design of the Regency P33-LP4. The fireplace is equipped with a built-in safety shut-off feature that automatically turns off the gas supply in case of an unexpected accident. Moreover, the glass front remains cool to the touch, reducing the risk of burns and making it family-friendly.

Flexibility is another advantage of the P33-LP4, as it can be installed in various configurations, including as a built-in unit or a freestanding fireplace. The options for installation enable homeowners to create a unique focal point in their living space, adapting to different architectural layouts.

In conclusion, the Regency P33-LP4 combines contemporary design, efficient heating technology, and safety features, making it an excellent choice for those seeking a stylish and functional propane fireplace. Its versatility and reliability enhance the home environment while providing a warm and inviting atmosphere for family and guests.