Regency P33-LP4 Thermopile Thermocouple, Glass Gasket, Door Glass, Flush Glass Replacement

Page 44

MAINTENANCE

THERMOPILE/

THERMOCOUPLE

1)Open the bottom louvers.

2)Loosen the thermocouple or thermopile with a 7/16" wrench.

3)Disconnect thermocouple by loosening nut from the valve with a 9mm wrench. Disconnect thermopile by loosening 2 screws marked TP on the valve.

4)Drop the thermocouple or thermopile down from the bracket and pull it out of the unit.

5)Reinstall the new ones in reverse order.

GLASS GASKET

If the glass gasket requires replacement use 5/8" fl at glass gasket for the Bay Front (Part

#936-243) and a tadpole glass gasket for the Flush Front (Part # 936-155).

DOOR GLASS

Your Regency® fi replace is supplied with high temperature,5mmNeoceramceramicglassthat will withstand the highest heat that your unit will produce. If your glass requires cleaning, we recommend using an approved glass cleaner available at all authorized dealers. Do not use abrasive materials. Do not clean the glass when hot.

In the event that you break your glass by impact, purchase your replacement from an authorized Regency® dealer only, and follow our step-by- step instructions for replacement.

WARNING: Do not operate the appliance with the glass panels removed, cracked or broken. Replacement of the glass panels should be done by a licensed or qualified service person.

Caution: Wear gloves when removing damaged or broken glass.

Flush Glass Replacement

Remove the fl ush door front. Remove the 4 glass clips from each corner. Slide in the new replacement glass. Push the 4 glass clips back onto the frame. The glass must have gasketing around it.

Bay Glass Replacement

1)Remove the door from the unit and place on a soft surface to prevent scratching.

2)Remove the nuts holding the glass clips in place and remove.

3)Replace the glass. The glass must have gasketing around it.

5)Reverse the previous steps, replace the glass clips and fasten with the nuts but do not over tighten, as this can break the glass.

6)Replace door on the Fireplace and check the seal.

44

Regency® P33-4 Zero Clearance Direct Vent Gas Fireplace

Page 43 Page 45
Image 44
Page 43 Page 45
Contents P33-4 Zero Clearance Information for MOBILE/MANUFACTURED Homes After First Sale To the New OwnerTable of Contents Safety Label Safety LabelRequirements For the State of Massachusetts onlyInstallation General Safety InformationImportant Message Before YOU StartInstallation Checklist Unit DimensionsLocating Your Fireplace Duct System OptionClearances Mantel LEG ClearancesRear Termination Framing and FinishingVertical Termination or Vertical Rise with Horizontal Unit Assembly Prior to Installation Top Standoff AssemblyVenting Introduction Top Facing Support Side Nailing StripsExterior Vent Termination Locations = Clearance to permanently closed window *min /30cmRegency Direct Vent Flex System Horizontal Terminations OnlyAlternate Without any joints or seamsMinimum and Maximum Vent Clearances Installation ProceduresFor Regency Direct Vent System Flex Flat Wall Installation Vent LengthThickness inches Required inches Max. Wall6-5/8 Rigid Pipe Cross Reference Chart Description6-5/8 Rigid Pipe Cross Reference Chart Rigid Pipe Venting Arrangements Vertical Terminations Propane & Natural GasInstallation Regency Direct Vent System Flex Horizontal Venting with Two 2 90o Elbows Option + H1Option +H1+H2 Option +H1Horizontal Venting with Three 3 90o Elbows Vertical Venting with Two 2 90o ElbowsOption +V1 +H1 Option +V1Vertical Venting with Three 3 90o Elbows Vertical Termination With CO-LINEAR Flex System Required PartsDescription Alternate Approved CapsVenting Arrangements Vertical Terminations Horizontal Distance FeetUnit Installation with Horizontal Termination Snorkel TerminationsThis allows for small adjustments Unit Installation With Vertical TerminationGAS Line Installation Pilot Adjustment GAS Pipe Pressure TestingHigh Elevation T. Valve DescriptionFor P33-4/H25-1 Using SIT 820 Nova Gas Valve Conversion KIT# 434-969 from NG to LPGlow on logs Installation of the DC Sparker for the P33-4 Unit Only 250 251Standard Flush Door Optional Flush TrimCutout 5th Grate TabFlush Louvers Double Screen DoorOptional BAY Trim Optional BAY DoorBAY Louvers Flush Louver Top Heat ShieldBay Louver Top Heat Shield Burner ON/OFF Control boxCut-Outs Full Screen DoorsCut-Out Oblong Hole Top Flange Bottom Hinge Location Bottom Grill Top GrillRemote Control Wall SwitchThermostat Wire Table Wall ThermostatWiring Diagrams Do not cut the ground terminal off under any circumstancesFor Propane Units and Units Equipped with DC Spark Boxes Installing the Optional FAN Secure the 2 boxes together With one screwOperating Instructions Copy of the Lighting Plate InstructionsLighting Procedure Shutdown ProcedureAeration Adjustment Operating InstructionsMaintenance Normal Operating Sounds MaintenanceLOG Replacement GAS AppliancesFlush Glass Replacement Bay Glass ReplacementThermopile Thermocouple Glass GasketInstalling Valve Diagram 3 Lift out Valve Tray AssemblyDiagram 2 Rear Log Stand & Valve Tray Assembly Removing ValveDescription Parts ListMain Assembly Parts List Burner & LOG Assembly Part DescriptionFlush Front & Louvers BAY Front & Louvers Warranty ConditionsInstaller Please complete the following information

P33-LP4 specifications

Regency P33-LP4 is an innovative and versatile propane gas fireplace designed to provide both warmth and ambiance while enhancing the aesthetic appeal of any living space. This model stands out for its combination of modern technology, functionality, and elegance, making it a popular choice among homeowners seeking an efficient heating solution without sacrificing style.

One of the key features of the P33-LP4 is its contemporary design. The fireplace presents a sleek, minimalist look that integrates seamlessly into both traditional and modern interiors. It offers a range of finishing options, including various trims and glass fronts, allowing homeowners to tailor the appearance of the fireplace to their personal taste and existing decor.

A hallmark of the Regency P33-LP4 is its advanced heating capabilities. With a powerful output of up to 33,000 BTUs, this fireplace can efficiently heat spaces of different sizes, making it suitable for both small cozy rooms and larger open areas. The unit also features a high-efficiency burner that maximizes heat production while reducing fuel consumption, which is ideal for energy-conscious users.

In terms of technology, the P33-LP4 boasts a user-friendly electronic ignition system that ensures reliable startups, even in colder temperatures. The fireplace can be controlled through a convenient remote or a wall switch, allowing users to adjust the flame height and heat settings with ease. Additionally, the unit incorporates a fan that circulates warm air throughout the room, enhancing overall heating efficiency and comfort.

Safety is paramount in the design of the Regency P33-LP4. The fireplace is equipped with a built-in safety shut-off feature that automatically turns off the gas supply in case of an unexpected accident. Moreover, the glass front remains cool to the touch, reducing the risk of burns and making it family-friendly.

Flexibility is another advantage of the P33-LP4, as it can be installed in various configurations, including as a built-in unit or a freestanding fireplace. The options for installation enable homeowners to create a unique focal point in their living space, adapting to different architectural layouts.

In conclusion, the Regency P33-LP4 combines contemporary design, efficient heating technology, and safety features, making it an excellent choice for those seeking a stylish and functional propane fireplace. Its versatility and reliability enhance the home environment while providing a warm and inviting atmosphere for family and guests.
Top Page Image Contents