Regency P33-LP4 Regency Direct Vent Flex System, Horizontal Terminations Only, Alternate

Page 12

INSTALLATION

REGENCY® DIRECT VENT FLEX SYSTEM

Horizontal Terminations Only

This venting system, in combination with the P33-4 Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by Warnock Hersey. The location of the termination cap must conform to the requirements in the "Exterior Vent Terminal Locations" Section .

Regency® Direct Vent Flex Termination Kit (Part # 946-513) includes all the parts needed to install the P33-4 with a maximum run of 2

feet. If installing the P33 with a continuous vent length of more than 2 ft (.6m) to a maximum of 10 ft. (3.0m) use Kit # 946-515 (4 ft) or 946-516 (10 ft) or see "Rigid Pipe Venting Systems" Section for alternate venting arrangements.

1)6-7/8" dia. fl exible liner (2 ft. length)

2)4" dia. fl exible liner (2 ft. length)

3)spring spacers (3)

4)thimble (2)

5)AstroCap termination cap (1)

6)screws (12)

7)tube of Mill Pac (1)

8)plated screws (8)

9)screws #8 x 1-1/2" drill point, stainless steel (4)

Notes:

Wall Thimble (2 pc)

(required in

Canada only)

 

AstroCapTM

4" (102mm)

Termination Cap

dia. flue pipe

(Part# 946-523/P)

spring spacer

1)

Liner sections should be continuous

 

without any joints or seams.

2)

Only Flex pipe purchased from Regency®

6-7/8"

See Figure 1 below for Alternate Caps.

may be used for Flex installations.

(173mm) dia. Flue pipe

IMPORTANT

If using any Cabinet Mantels with Part # 510956, 510958, 510962, 510964 and 510834 the wall thimble must be secured fi rst and venting must be attached to unit before sliding into fi nal position.

Also Rigid Vent venting cannot be used with any of the mantels noted above. See Price Pages for alternative options.

MINIMUM

RIGID PIPE CENTER-LINE

MINIMUM

FLEX KIT CENTER-LINE

Alternate

Horizontal

Termination

Caps

Figure 1

 

Wherever necessary due to

 

external location of cap, the

 

AstroCapcanbereplacedwith

 

the FPI Riser Vent Termination

 

Cap or the Dura-Vent Snorkel

 

Termination Cap.

12

Regency® P33-4 Zero Clearance Direct Vent Gas Fireplace

Page 11 Page 13
Image 12
Page 11 Page 13
Contents P33-4 Zero Clearance Information for MOBILE/MANUFACTURED Homes After First Sale To the New OwnerTable of Contents Safety Label Safety LabelRequirements For the State of Massachusetts onlyInstallation General Safety InformationImportant Message Before YOU StartInstallation Checklist Unit DimensionsLocating Your Fireplace Duct System OptionClearances Mantel LEG ClearancesFraming and Finishing Vertical Termination or Vertical Rise with HorizontalRear Termination Unit Assembly Prior to Installation Top Standoff AssemblyVenting Introduction Top Facing Support Side Nailing StripsExterior Vent Termination Locations = Clearance to permanently closed window *min /30cmRegency Direct Vent Flex System Horizontal Terminations OnlyAlternate Without any joints or seamsInstallation Procedures For Regency Direct Vent System FlexMinimum and Maximum Vent Clearances Flat Wall Installation Vent LengthThickness inches Required inches Max. Wall6-5/8 Rigid Pipe Cross Reference Chart Description6-5/8 Rigid Pipe Cross Reference Chart Rigid Pipe Venting Arrangements Vertical Terminations Propane & Natural GasInstallation Regency Direct Vent System Flex Horizontal Venting with Two 2 90o Elbows Option + H1Option +H1+H2 Option +H1Horizontal Venting with Three 3 90o Elbows Vertical Venting with Two 2 90o ElbowsOption +V1 +H1 Option +V1Vertical Venting with Three 3 90o Elbows Vertical Termination With CO-LINEAR Flex System Required PartsDescription Alternate Approved CapsVenting Arrangements Vertical Terminations Horizontal Distance FeetUnit Installation with Horizontal Termination Snorkel TerminationsUnit Installation With Vertical Termination GAS Line InstallationThis allows for small adjustments Pilot Adjustment GAS Pipe Pressure TestingHigh Elevation T. Valve DescriptionFor P33-4/H25-1 Using SIT 820 Nova Gas Valve Conversion KIT# 434-969 from NG to LPGlow on logs Installation of the DC Sparker for the P33-4 Unit Only 250 251Standard Flush Door Optional Flush TrimCutout 5th Grate TabFlush Louvers Double Screen DoorOptional BAY Trim Optional BAY DoorBAY Louvers Flush Louver Top Heat ShieldBay Louver Top Heat Shield Burner ON/OFF Control boxFull Screen Doors Cut-Out Oblong Hole Top Flange BottomCut-Outs Hinge Location Bottom Grill Top GrillRemote Control Wall SwitchThermostat Wire Table Wall ThermostatWiring Diagrams Do not cut the ground terminal off under any circumstancesFor Propane Units and Units Equipped with DC Spark Boxes Installing the Optional FAN Secure the 2 boxes together With one screwOperating Instructions Copy of the Lighting Plate InstructionsLighting Procedure Shutdown ProcedureAeration Adjustment Operating InstructionsMaintenance Normal Operating Sounds MaintenanceLOG Replacement GAS AppliancesFlush Glass Replacement Bay Glass ReplacementThermopile Thermocouple Glass GasketInstalling Valve Diagram 3 Lift out Valve Tray AssemblyDiagram 2 Rear Log Stand & Valve Tray Assembly Removing ValveParts List Main AssemblyDescription Parts List Burner & LOG Assembly Part DescriptionFlush Front & Louvers BAY Front & Louvers Warranty ConditionsInstaller Please complete the following information

P33-LP4 specifications

Regency P33-LP4 is an innovative and versatile propane gas fireplace designed to provide both warmth and ambiance while enhancing the aesthetic appeal of any living space. This model stands out for its combination of modern technology, functionality, and elegance, making it a popular choice among homeowners seeking an efficient heating solution without sacrificing style.

One of the key features of the P33-LP4 is its contemporary design. The fireplace presents a sleek, minimalist look that integrates seamlessly into both traditional and modern interiors. It offers a range of finishing options, including various trims and glass fronts, allowing homeowners to tailor the appearance of the fireplace to their personal taste and existing decor.

A hallmark of the Regency P33-LP4 is its advanced heating capabilities. With a powerful output of up to 33,000 BTUs, this fireplace can efficiently heat spaces of different sizes, making it suitable for both small cozy rooms and larger open areas. The unit also features a high-efficiency burner that maximizes heat production while reducing fuel consumption, which is ideal for energy-conscious users.

In terms of technology, the P33-LP4 boasts a user-friendly electronic ignition system that ensures reliable startups, even in colder temperatures. The fireplace can be controlled through a convenient remote or a wall switch, allowing users to adjust the flame height and heat settings with ease. Additionally, the unit incorporates a fan that circulates warm air throughout the room, enhancing overall heating efficiency and comfort.

Safety is paramount in the design of the Regency P33-LP4. The fireplace is equipped with a built-in safety shut-off feature that automatically turns off the gas supply in case of an unexpected accident. Moreover, the glass front remains cool to the touch, reducing the risk of burns and making it family-friendly.

Flexibility is another advantage of the P33-LP4, as it can be installed in various configurations, including as a built-in unit or a freestanding fireplace. The options for installation enable homeowners to create a unique focal point in their living space, adapting to different architectural layouts.

In conclusion, the Regency P33-LP4 combines contemporary design, efficient heating technology, and safety features, making it an excellent choice for those seeking a stylish and functional propane fireplace. Its versatility and reliability enhance the home environment while providing a warm and inviting atmosphere for family and guests.
Top Page Image Contents