Regency P33-LP4 Framing and Finishing, Vertical Termination or Vertical Rise with Horizontal

Page 9

INSTALLATION

FRAMING AND FINISHING

1)Determine the total thickness of facing material (e.g. drywall plus ceramic tiles) to allow the fi nished surface to be fl ush with the front of the unit. Total facing thickness can vary from 1/2" (13mm) to 1-1/4" (32mm) thick.

Install Side Nailing Strips, and Top Facing Supportbeforeunitisslippedintoposition. See "Unit Assembly Prior to Installation" Section

2)Frame in the enclosure for the unit with framing material.

Vertical Termination or

Vertical Rise with Horizontal

Termination

For Both Rigid & Flex

NOTE: If this is an outside corner, the minimum distance between the vent and the outside corner is 6" (15cm) with AstroCap termination cap or 12" (30cm) with Rigid Vent termination cap. (For example Dura-Vent).

Rear Termination

For Rigid Vent

For Flex Vent

For Both Rigid & Flex

NOTE: If this isan outsidecorner, the minimum distance between the vent and the outside corner is 6" (15cm) with AstroCap termination cap or 12" (30cm) with Rigid Vent termination cap. (For Example Dura-Vent).

3)For exterior walls, insulate the enclosure to the same degree as the rest of the house, apply vapour barrier and drywall, as per local installation codes. (Do not insulate the fireplace itself.)

4)The top of the unit must not be closer than 30" (762mm) to the ceiling.

5)Combustible material may be brought up to the top and sides of the unit and be covered with ceramic tiles, bricks, rock or other suitable combustible fi nishing materials.

Note: Theunitdoesnothavetobecompletely enclosed in a chase. The clearance on top of the unit is 0" to the standoffs so combustiblebuildingmaterialscanbe laid directly on top of the standoffs. You must maintain clearance from the vent to combustible materials for flex or for Rigid Vent (Refer to "Clearances" Section).

 

Rigid Vent

 

Minimum Clearances

 

 

Top Header

 

 

 

10" (254mm)

 

1/2"

 

dia. Hole through

 

(13mm)

wall for Dura-Vent

 

Drywall

 

 

 

 

1-1/2"

 

30”

(762mm)

(38mm)

 

 

 

 

4"

3"

16-1/2”

 

(102mm)(76mm)

(419mm)

 

Opening for gas

Minimum

 

connection

 

 

 

Flex Vent

 

Minimum Clearances

 

 

Top Header

 

1/2"

 

10" (254mm)

 

 

dia. Hole through

(13mm)

 

Drywall

 

wall for Flex

 

1-1/2"

 

26”

(660mm)

(38mm)

 

 

 

 

4"

3"

12-3/4”

 

(102mm)(76mm)

(324mm)

 

Opening for gas

Minimum

 

connection

 

 

6)Use steel studs for framing where the 1-1/2" (38mm) clearance from the vent to combustible material cannot be maintained.

The HeatWave Duct Kit has different clearance and framing requirements, check the HeatWave manual for details.

Regency® P33-4 Zero Clearance Direct Vent Gas Fireplace

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents P33-4 Zero Clearance To the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Safety Label Safety LabelFor the State of Massachusetts only RequirementsGeneral Safety Information InstallationImportant Message Before YOU StartUnit Dimensions Installation ChecklistLocating Your Fireplace Duct System OptionMantel LEG Clearances ClearancesFraming and Finishing Vertical Termination or Vertical Rise with HorizontalRear Termination Top Standoff Assembly Unit Assembly Prior to InstallationVenting Introduction Top Facing Support Side Nailing Strips= Clearance to permanently closed window *min /30cm Exterior Vent Termination LocationsHorizontal Terminations Only Regency Direct Vent Flex SystemAlternate Without any joints or seamsInstallation Procedures For Regency Direct Vent System FlexMinimum and Maximum Vent Clearances Vent Length Flat Wall InstallationThickness inches Required inches Max. WallDescription 6-5/8 Rigid Pipe Cross Reference Chart6-5/8 Rigid Pipe Cross Reference Chart Vertical Terminations Propane & Natural Gas Rigid Pipe Venting ArrangementsInstallation Regency Direct Vent System Flex Option + H1 Horizontal Venting with Two 2 90o ElbowsOption +H1+H2 Option +H1Vertical Venting with Two 2 90o Elbows Horizontal Venting with Three 3 90o ElbowsOption +V1 +H1 Option +V1Vertical Venting with Three 3 90o Elbows Required Parts Vertical Termination With CO-LINEAR Flex SystemDescription Alternate Approved CapsHorizontal Distance Feet Venting Arrangements Vertical TerminationsSnorkel Terminations Unit Installation with Horizontal TerminationUnit Installation With Vertical Termination GAS Line InstallationThis allows for small adjustments GAS Pipe Pressure Testing Pilot AdjustmentHigh Elevation T. Valve DescriptionConversion KIT# 434-969 from NG to LP For P33-4/H25-1 Using SIT 820 Nova Gas ValveGlow on logs Installation of the DC Sparker for the P33-4 Unit Only 251 250Optional Flush Trim Standard Flush DoorCutout 5th Grate TabDouble Screen Door Flush LouversOptional BAY Trim Optional BAY DoorFlush Louver Top Heat Shield BAY LouversBay Louver Top Heat Shield Burner ON/OFF Control boxFull Screen Doors Cut-Out Oblong Hole Top Flange BottomCut-Outs Top Grill Hinge Location Bottom GrillWall Switch Remote ControlThermostat Wire Table Wall ThermostatDo not cut the ground terminal off under any circumstances Wiring DiagramsFor Propane Units and Units Equipped with DC Spark Boxes Secure the 2 boxes together With one screw Installing the Optional FANCopy of the Lighting Plate Instructions Operating InstructionsShutdown Procedure Lighting ProcedureAeration Adjustment Operating InstructionsNormal Operating Sounds Maintenance MaintenanceLOG Replacement GAS AppliancesBay Glass Replacement Flush Glass ReplacementThermopile Thermocouple Glass GasketDiagram 3 Lift out Valve Tray Assembly Installing ValveDiagram 2 Rear Log Stand & Valve Tray Assembly Removing ValveParts List Main AssemblyDescription Parts List Part Description Burner & LOG AssemblyFlush Front & Louvers BAY Front & Louvers Conditions WarrantyInstaller Please complete the following information

P33-LP4 specifications

Regency P33-LP4 is an innovative and versatile propane gas fireplace designed to provide both warmth and ambiance while enhancing the aesthetic appeal of any living space. This model stands out for its combination of modern technology, functionality, and elegance, making it a popular choice among homeowners seeking an efficient heating solution without sacrificing style.

One of the key features of the P33-LP4 is its contemporary design. The fireplace presents a sleek, minimalist look that integrates seamlessly into both traditional and modern interiors. It offers a range of finishing options, including various trims and glass fronts, allowing homeowners to tailor the appearance of the fireplace to their personal taste and existing decor.

A hallmark of the Regency P33-LP4 is its advanced heating capabilities. With a powerful output of up to 33,000 BTUs, this fireplace can efficiently heat spaces of different sizes, making it suitable for both small cozy rooms and larger open areas. The unit also features a high-efficiency burner that maximizes heat production while reducing fuel consumption, which is ideal for energy-conscious users.

In terms of technology, the P33-LP4 boasts a user-friendly electronic ignition system that ensures reliable startups, even in colder temperatures. The fireplace can be controlled through a convenient remote or a wall switch, allowing users to adjust the flame height and heat settings with ease. Additionally, the unit incorporates a fan that circulates warm air throughout the room, enhancing overall heating efficiency and comfort.

Safety is paramount in the design of the Regency P33-LP4. The fireplace is equipped with a built-in safety shut-off feature that automatically turns off the gas supply in case of an unexpected accident. Moreover, the glass front remains cool to the touch, reducing the risk of burns and making it family-friendly.

Flexibility is another advantage of the P33-LP4, as it can be installed in various configurations, including as a built-in unit or a freestanding fireplace. The options for installation enable homeowners to create a unique focal point in their living space, adapting to different architectural layouts.

In conclusion, the Regency P33-LP4 combines contemporary design, efficient heating technology, and safety features, making it an excellent choice for those seeking a stylish and functional propane fireplace. Its versatility and reliability enhance the home environment while providing a warm and inviting atmosphere for family and guests.
Top Page Image Contents