Regency B36X installation manual Unit Installation, Astrocapxl

Page 33

INSTALLATION

UNIT INSTALLATION

HORIZONTAL TERMINATION

WITH 5" X 8" FLEX VENT SYSTEM

Note: 5" x 8" venting is limited to vent configurations found on page 17 of this manual.

Note: A top clearance of 2"(51mm) and side

&bottom clearance of 1-1/2"(38mm) must be maintained; except when passing through a wall, ceiling, or at the termination where the use of a firestop or wall thimble reduces the required clearance to 1-1/2" (38mm). We recommend framing a 11"(279mm) x 11"(279mm) (inside dimensions) hole to give structural rigidity for mounting the termination.

1)Locate the unit in the framing, rough in the gas (preferably on the right side of the unit). Locate the centerline of the termination and mark wall accordingly. Cut an 11"(279mm) hole in the wall (inside dimension).

Note: If installing termination on a siding covered wall, a vinyl siding standoff or vinyl furring strips must be used

on top and bottom. Fasten the other thimble half to the inside wall. The thimble halves slip inside each other and can be adjusted for 2 x 4 or 2 x 6 walls.

5)Slip the assembled liner and termination assembly through the thimble making sure the termination cap faces up (there are markings on the cap that show which way is up). This will position the termination cap with proper down slope for draining water. Fasten the cap to the outer wall with the 4 supplied screws.

6)Pull the centre 5"(127mm) liner and outer 8"(203mm) liner out enough to slip over the flue collars of the fireplace. (You may wish to cut the liner shorter to make it more workable.) Do not bend liner more than 90o. The liners must slip over the collars a minimum of 1-3/8".

7)Apply Mill Pac over the fireplace inner collar and slip the 5"(127mm) liner down over it and attach with 3 supplied screws.

8)Do the same with the 8"(203mm) liner.

9)Apply a bead of silicone between the thimble and termination and around the outer edge of the terminal at the wall in order to keep the water out.

IMPORTANT: Do not locate termination hood where excessive snow or ice buildup may occur. Be sure to check vent termination area after snow falls, and clear to prevent accidental blockage of venting system. When using snow blowers, make sure snow is not directed towards vent termination area.

ASTROCAPXL

DIMENSIONS (946-623/P)

to ensure that the termination is not recessed into the siding.

2)Level the fireplace and fasten it to the fram- ing using nails or screws through the nailing strips.

3)Assemble the vent assembly by applying Mill Pac to the 5"(127mm) inner collar of the termination and slipping the 5"(127mm) liner over it at least 1-3/8" (35mm). Fasten with the 3 screws (drilling pilot holes will make this easier). Apply Mill Pac or high temperature silicone to the 8"(203mm) flex pipe and slip it over the 8" outer collar of the vent terminal at least 1-3/8"(35mm) and fasten with the 3 screws.

NOTE: Horizontal sections must be sup- ported at intervals not exceeding 3 feet (0.9 meter). (Flame picture and performance will be affected by sags in the liner).

4)Separate the 2 halves of the wall thimble and securely fasten the one with the tabs to the outside wall making sure that the tabs are

 

 

2” x 4” or 2” x 6”

5” dia. flue pipe

AstroCap XL

with spring spacer

Termination Cap

 

 

8" dia.

 

 

air intake

Screws

 

 

Vinyl Siding

Screws

Wall Thimble

 

 

Regency Bellavista™ B36X Gas Fireplace

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Regency Bellavista B36X Gas Fireplace Regency Bellavista B36X Gas Fireplace Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Copy of Safety Decal Safety LabelMA Code CO Detector RequirementsUnit Dimensions DimensionsGeneral Safety Information InstallationImportant Message Save These Instructions Before YOU StartDiagram Installation ChecklistLocating Your GAS Fireplace Heatwave Duct System OptionalClearances Mantel LEG Clearances Mantel ClearancesFraming Framing Dimensions Description B36XFinishing Important Finishing Detail NoteFull Screen Doors Only Unit Assembly Prior to Installation Before YOU Start Screw PositionPlates can be Folded out Unit Assembly Prior to Installation Adjustable Tension Latch locationBaffle Plate Exhaust Assembly Intake Collar Diagram Diagram Exhaust Assembly Intake CollarVenting Introduction Minimum Clearance Requirements Exterior Vent Termination RequirementsInstallation Vertical Venting Configurations Approved Venting Configurations6-5/8 Rigid Pipe Cross Reference ChartInstallation Installation Installation Horizontal Terminations Regency Direct Vent Flex System 5 X Horizontal Termination Horizontal Terminations Rigid Pipe Venting Arrangements 5 XTop Vent No Vertical Rise Rear Vent w/ Horizontal TerminationHorizontal or Vertical Terminations Rigid Pipe Venting Systems58DVA-WT Venting Arrangements Allowable Vertical Terminations6 5/8 Pipe Venting Arrangements Horizontal Venting with TWO 2 90O Elbows Venting Arrangements Horizontal TerminationVertical Venting with Three 3 90O Elbows Horizontal Venting with Three 3 90O ElbowsAlternate Approved Caps Vertical Termination With CO-LINEAR Flex SystemFor Both Residential & Manufactured Homes Rigid Vent Systems Astrocapxl Unit InstallationUnit Installation With Vertical Termination GAS Line InstallationThis allows for small adjustments GAS Pipe Pressure Testing Pilot AdjustmentHigh Elevation T. Valve DescriptionWiring Diagram Aeration AdjustmentMinimum Air Shutter Opening Do not cut the ground terminal off under any circumstancesFor Propane Units and Units Equipped with DC Spark Boxes Wiring Diagram for Gtmf RemoteDiagram 2 Vent restrictor installed on top exhaust assembly Vent RESTRICTOR, Baffle & Heat Deflector InstallationBaffl e Plate Heat Defl ectorConversion KIT# 556-969 from NG to LP Conversion Kit Contains Qty DescriptionShut off the gas supply Cap Ignitor Wire Piezo DC Sparker InstallationSparker Ignitor Wire DC Sparker Generator WiresBack Panel Installed Final Brick Panel Installation Brick Panel InstallationHandle with care. do not Force Into Position Ensure that the logs are not in the unitPanel Installation Optional Stainless Steel / Black EnamelSlots on Top Panel Black Enamel Panel Installation Log Kit #556-930 contains the following pieces LOG SET InstallationVermiculite NotchNotch in log B Notch in log F2nd Grate Tab Notch in log D Lava Rocks Remote Control Wall SwitchWall Thermostat Installation See Diagram FAN InstallationSlide the the Fan control box Ground LugFlush Glass Door Installation Tabs in Firebox DiagramAdjustable Tension Latch location Diagram Flush Louvers and Flush Panel Installation Optional Finishing Trim InstallationLower PanelDo not tighten the screws leave them loose for the next step Full Screen Arch Door and Frame InstallationOperating Instructions Copy of Lighting Plate Instructions Maintenance Installing Valve Diagram 1 Remove the left and right screwsRemoving Valve Main Assembly Parts List2622 Burner Assembly Regency Bellavista B36X Gas Fireplace Regency Bellavista B36X Gas Fireplace Warranty Limited Lifetime WarrantyInstaller Please complete the following information

B36X specifications

The Regency B36X is a remarkable gas fireplace that combines elegance with efficiency, designed to seamlessly integrate into any contemporary or traditional living space. This model from Regency is especially popular for its powerful performance and stunning aesthetics, providing both warmth and a focal point for any room.

One of the standout features of the B36X is its impressive heating capabilities. It boasts a heat output of up to 34,000 BTUs, allowing it to efficiently warm spaces up to 1,500 square feet, making it suitable for larger areas. The fireplace utilizes a direct vent system, which ensures that combustion gases are expelled outside while drawing in fresh air for combustion. This contributes to enhanced indoor air quality, as it does not rely on the oxygen from within the home.

In terms of design, the B36X features a sleek, contemporary appearance, characterized by its large viewing area framed by a clean face. Its innovative design maximizes the flame visibility, creating a captivating ambiance. Homeowners can choose from a variety of finishing options, including versatile color choices and customizable trim, allowing the fireplace to match specific interior decor styles.

The fireplace is equipped with advanced technology, including an electronic ignition system that ensures reliable, effortless lighting. For added convenience, optional remote control features enable users to adjust the flame height and temperature with ease. Furthermore, the B36X also supports the installation of a wall thermostat, providing enhanced temperature control and efficiency.

Safety is a crucial element of the Regency B36X. Its glass front is designed with safety in mind, remaining cooler to the touch, which is especially important for households with children or pets. Additionally, the unit is equipped with built-in safety shut-off features that activate in the event of any irregularities in operation.

Energy efficiency is another hallmark of the B36X. Its high efficiency rating ensures that the fuel consumed translates into effective heating, ultimately leading to savings on utility bills. The fireplace meets or exceeds various environmental standards, making it an eco-conscious choice for homeowners looking to reduce their carbon footprint.

In conclusion, the Regency B36X offers a perfect blend of style, functionality, and advanced technology. With its powerful heating capabilities, customizable designs, and enhanced safety features, it stands out as an exceptional choice for anyone looking to enhance their home’s comfort and aesthetics.
Top Page Image Contents