Regency B36X Horizontal Terminations Rigid Pipe Venting Arrangements 5 X, Max .9m

Page 24

INSTALLATION

HORIZONTAL TERMINATIONS

RIGID PIPE VENTING ARRANGEMENTS (5" X 8")

Vinyl Siding

Standoff (Optional)

Horizontal

Termination

Cap

Wall Thimble

Pipe Length

90o Elbow

Rigid Pipe Adaptor

 

Horizontal Termination

A

Top Vent - No Vertical Rise

 

• When venting with a 90° elbow directly

A

off the unit, must use 5" X 8" Astrocap™

Flex vent or approved Rigid Vent System

 

 

• Max. 3 ft. horizontal run

BRear Vent w/ Horizontal Termination

Can only use 5" x 8" venting

Max. 3ft. horizontal run

Vinyl Siding

Standoff (Optional)

Horizontal

Termination

Cap

Wall Thimble

Pipe Length

Rigid Pipe Adaptor

B

The diagrams show all allowable combinations of vent runs with 5" x 8" venting using the Regency direct vent system or rigid vent system. A vent guard should be used whenever the termination is lower than the specified minimum or as per local codes.

For horizontal terminations the Regency Direct Vent Flex System (see page 14) may be used for installations with a maximum continuous vent length of 3ft (0.9m).

Note: Must use optional rigid pipe adaptor (Part # 770-994) when using Rigid Pipe vent systems.

Maintain clearance to combustibles.

Horizontal vent must be supported every 3 feet.

Firestops are required at each floor level and whenever passing through a wall.

0

Horizontal (Feet)

2

4

6

8

Vertical Height (Feet)

12

10

8

 

1/4"(1.1m)-44Rigid

1/8"(1.0m)-42Flex

6

 

 

 

 

4

 

 

 

2

Max. 36”(0.9m)

 

 

 

 

 

0

 

 

 

Factory Setting - No Restrictor Required

Factory Setting - No Restrictor Required

24

Regency Bellavista™ B36X Gas Fireplace

Image 24
Contents Regency Bellavista B36X Gas Fireplace Information for MOBILE/MANUFACTURED Homes After First Sale Regency Bellavista B36X Gas FireplaceTable of Contents Safety Label Copy of Safety DecalRequirements MA Code CO DetectorDimensions Unit DimensionsInstallation General Safety InformationImportant Message Save These Instructions Before YOU StartInstallation Checklist DiagramLocating Your GAS Fireplace Heatwave Duct System OptionalClearances Mantel Clearances Mantel LEG ClearancesFraming Dimensions Description B36X FramingFinishing Important Finishing Detail NoteFull Screen Doors Only Unit Assembly Prior to Installation Before YOU Start Screw PositionPlates can be Folded out Unit Assembly Prior to Installation Adjustable Tension Latch locationBaffle Plate Exhaust Assembly Intake Collar Diagram Diagram Exhaust Assembly Intake CollarVenting Introduction Exterior Vent Termination Requirements Minimum Clearance RequirementsInstallation Approved Venting Configurations Vertical Venting ConfigurationsRigid Pipe Cross Reference Chart 6-5/8Installation Installation Installation Horizontal Terminations Regency Direct Vent Flex System 5 X Horizontal Terminations Rigid Pipe Venting Arrangements 5 X Horizontal TerminationTop Vent No Vertical Rise Rear Vent w/ Horizontal TerminationRigid Pipe Venting Systems Horizontal or Vertical Terminations58DVA-WT Venting Arrangements Allowable Vertical Terminations6 5/8 Pipe Venting Arrangements Venting Arrangements Horizontal Termination Horizontal Venting with TWO 2 90O ElbowsHorizontal Venting with Three 3 90O Elbows Vertical Venting with Three 3 90O ElbowsVertical Termination With CO-LINEAR Flex System Alternate Approved CapsFor Both Residential & Manufactured Homes Rigid Vent Systems Unit Installation AstrocapxlUnit Installation With Vertical Termination GAS Line InstallationThis allows for small adjustments Pilot Adjustment GAS Pipe Pressure TestingHigh Elevation T. Valve DescriptionAeration Adjustment Wiring DiagramMinimum Air Shutter Opening Do not cut the ground terminal off under any circumstancesWiring Diagram for Gtmf Remote For Propane Units and Units Equipped with DC Spark BoxesVent RESTRICTOR, Baffle & Heat Deflector Installation Diagram 2 Vent restrictor installed on top exhaust assemblyBaffl e Plate Heat Defl ectorConversion KIT# 556-969 from NG to LP Conversion Kit Contains Qty DescriptionShut off the gas supply Cap DC Sparker Installation Ignitor Wire PiezoSparker Ignitor Wire DC Sparker Generator WiresBrick Panel Installation Back Panel Installed Final Brick Panel InstallationHandle with care. do not Force Into Position Ensure that the logs are not in the unitPanel Installation Optional Stainless Steel / Black EnamelSlots on Top Panel Black Enamel Panel Installation LOG SET Installation Log Kit #556-930 contains the following piecesVermiculite NotchNotch in log B Notch in log F2nd Grate Tab Notch in log D Lava Rocks Remote Control Wall SwitchWall Thermostat Installation FAN Installation See DiagramSlide the the Fan control box Ground LugFlush Glass Door Installation Tabs in Firebox DiagramAdjustable Tension Latch location Diagram Optional Finishing Trim Installation Flush Louvers and Flush Panel InstallationLower PanelFull Screen Arch Door and Frame Installation Do not tighten the screws leave them loose for the next stepOperating Instructions Copy of Lighting Plate Instructions Maintenance Installing Valve Diagram 1 Remove the left and right screwsRemoving Valve Parts List Main Assembly2622 Burner Assembly Regency Bellavista B36X Gas Fireplace Regency Bellavista B36X Gas Fireplace Warranty Warranty Limited LifetimeInstaller Please complete the following information

B36X specifications

The Regency B36X is a remarkable gas fireplace that combines elegance with efficiency, designed to seamlessly integrate into any contemporary or traditional living space. This model from Regency is especially popular for its powerful performance and stunning aesthetics, providing both warmth and a focal point for any room.

One of the standout features of the B36X is its impressive heating capabilities. It boasts a heat output of up to 34,000 BTUs, allowing it to efficiently warm spaces up to 1,500 square feet, making it suitable for larger areas. The fireplace utilizes a direct vent system, which ensures that combustion gases are expelled outside while drawing in fresh air for combustion. This contributes to enhanced indoor air quality, as it does not rely on the oxygen from within the home.

In terms of design, the B36X features a sleek, contemporary appearance, characterized by its large viewing area framed by a clean face. Its innovative design maximizes the flame visibility, creating a captivating ambiance. Homeowners can choose from a variety of finishing options, including versatile color choices and customizable trim, allowing the fireplace to match specific interior decor styles.

The fireplace is equipped with advanced technology, including an electronic ignition system that ensures reliable, effortless lighting. For added convenience, optional remote control features enable users to adjust the flame height and temperature with ease. Furthermore, the B36X also supports the installation of a wall thermostat, providing enhanced temperature control and efficiency.

Safety is a crucial element of the Regency B36X. Its glass front is designed with safety in mind, remaining cooler to the touch, which is especially important for households with children or pets. Additionally, the unit is equipped with built-in safety shut-off features that activate in the event of any irregularities in operation.

Energy efficiency is another hallmark of the B36X. Its high efficiency rating ensures that the fuel consumed translates into effective heating, ultimately leading to savings on utility bills. The fireplace meets or exceeds various environmental standards, making it an eco-conscious choice for homeowners looking to reduce their carbon footprint.

In conclusion, the Regency B36X offers a perfect blend of style, functionality, and advanced technology. With its powerful heating capabilities, customizable designs, and enhanced safety features, it stands out as an exceptional choice for anyone looking to enhance their home’s comfort and aesthetics.