Nilfisk-ALTO 46/53 manual Hopper Door Lever See Figure, Hopper Filter Cover See Figure

Page 27

OPERATION OF CONTROLS AND GAUGES

HOPPER

DOOR

LEVER

(Variable Dump

Hopper Only)

C1717A

FIGURE 27

HOPPER

LEVER

C1717B

FIGURE 28

LIFT TO OPEN

C1725A-batt

FIGURE 29

HOPPER DOOR LEVER (See Figure 27)

The hopper door lever is located on the operator’s com- partment and is used to close and open the hopper dump door. The lever is a two position hydraulic valve that is spring loaded to the center position which “HOLDS” the hopper door in position.

To open the hopper dump door for sweeping or dumping, push the lever to the “OPEN” direction.

To close the hopper dump door for dumping or transport- ing, push the lever fully back in the “CLOSE” direction, and hold for 3 seconds or until you hear the door close.

HOPPER LIFT LEVER (See Figure 28)

The hopper lift lever is located on the operator’s compart- ment console. The lever is a two position hydraulic valve that controls the operation of the hopper lift system. The lever is spring loaded to the center position which stops hopper movement and “HOLDS” the hopper at the present position.

To raise the hopper for dumping, move the lever to the “RAISE” position and hold until the hopper reaches the desired height, then release.

WARNING

The hopper may drop unexpectedly and cause injury, always engage the safety arm before working under the hopper.

To lower the hopper after dumping, move the lever to the “LOWER” position until the hopper is fully lowered and seated in the machine, then release.

HOPPER FILTER COVER (See Figure 29)

The hopper filter cover is actually the front cover or “hood” of the machine. It opens forward by releasing latches to access the filter compartment for service/inspection of the dust control filter and optional hopper temp sensor.

Inspect gaskets daily. Replace any gaskets that show signs of deterioration. Failure to maintain the gaskets in serviceable condition will degrade dust control at the floor and will result in less than optimal sweeping performance.

American-Lincoln

1-27

ATS 46/53 Battery

 

Page 26 Page 28
Image 27
Page 26 Page 28
Contents American-Lincoln Technology Table of Contents American-Lincoln ATS 46/53 Battery Options Specifications Hopper WarrantySqueegee TanksMachine Dimensions SAE Grade Standard Hardware & Torque ValuesHydraulic Torque Requirements Hydraulic Torque RequirementsDECIMAL-METRIC Conversion Table DECIMAL-METRIC Conversion TablePreparing the Machine for Operation Machine PreparationRead the Instruction Book Safety InstructionsSafety Instructions Safety Instructions Light Switch See Figure Operation of Controls and GaugesHorn Button See Figure Seat Position Adjustment See Figure KEY Switch See FigureFORWARD/REVERSE Switch See Figure Combination Battery Condition & Hour MeterTo Engage the Safety ARM Filter Shaker SwitchSide Broom Lever See Figure Side Broom Adjustment See figureMain Broom Adjustment See Figure Side Broom LeverDust Control Switch See Figure Scrub Deck Switch See FigureSqueegee Switch See Figure To Disconnect Water Hose Solution Control See FigureNON-RECYCLING or Standard Scrubbing System Recycling or ESP & Autofil SystemCharging System Light Hopper Temperature Light OptionSolution LOW Light Recovery High LightFoot Pedal Accelerator Brake PedalParking Brake Hopper Dump Door Lever See Figure Hopper Lift Lever See FigureBACK-UP Alarm Switch Option See Figure C1702batt Turn Signal 4-Way Option See FigureFront Cover Latch See Figure C1719C1718 Filter Panel Latch See FigureMain Broom Compartment Doors See Figure Hydraulic ReservoirLevel Sight Gauge Hydraulic Reservoir Level Sight GaugeHopper Filter Cover See Figure Hopper Door Lever See FigureESP System Operating Instructions Recycling System Detergent LOW ON/OFF SwitchSolution Tank Detergent Tank Recovery Scrubbing System HOW IT WorksNON-RECYCLING or Standard Scrubbing System HOW IT Works Floor Contact Recovery or ESP and Autofil System HOW IT WorksOrifice CheckOperating Instructions Emptying the Debris Hopper POST-OPERATION ChecklistBattery Charging Instructions Storage for BATTERY-POWERED MachinesMain Aisle Helpful Hints for Cleaning OperationHour Maintenance Checklist Service ChartService Chart Hour Weekly Maintenance ChecklistFront Service Precautions Service PrecautionsService Instructions Replacing the Side Broom Side Broom ServiceChecking the Hopper Seals Hopper ServiceCleaning the Hopper Cleaning the Dust Control FilterDust Flaps Replacing the Dust Control FilterBrakes Brake ServiceAdjusting the Brake Pedal Adjusting the BrakesFilling the Hydraulic Reservoir General Machine MaintenanceCleaning the Hydraulic System Fill Hydraulic ReservoirReplacing the Scrub Brush Solution LOW Warning LightRecovery High Warning Light Brush LatchRear Squeegee Adjusting CastersRecycling Pump ESP System Recycling Pump StorageBattery Abbreviations Screws Parts List LegendGeneral Troubleshooting Problem Probable Cause RemedyCheck & repair. orSereplaceahC -.Lynn Internet Alto Headquarters Ordering Parts

46/53 specifications

The Nilfisk-ALTO 46/53 is a powerful and versatile range of professional vacuum cleaners designed to meet the demanding needs of various cleaning applications. Known for their efficiency and reliability, these models are ideal for both commercial and industrial environments. With a robust construction, the Nilfisk-ALTO 46/53 series is built to withstand the wear and tear of daily use.

One of the standout features of the Nilfisk-ALTO 46/53 is its impressive suction power. Equipped with high-efficiency motors, these vacuum cleaners ensure optimal performance while consuming less energy. This not only enhances productivity but also contributes to cost savings and environmental sustainability.

The design of the Nilfisk-ALTO 46/53 is user-friendly, featuring an ergonomic handle and lightweight construction that make it easy to maneuver in tight spaces. Its compact design does not compromise on the capacity, as the model comes with a generous tank size, allowing for extended cleaning sessions without frequent interruptions for disposal.

Another notable characteristic of the Nilfisk-ALTO 46/53 is its advanced filtration system. The vacuum includes a HEPA filter, which captures fine dust and allergens, ensuring a cleaner and healthier environment. This feature is particularly beneficial in settings where air quality is critical, such as hospitals and laboratories.

In terms of versatility, the Nilfisk-ALTO 46/53 is equipped with various accessories and attachments designed to tackle different surfaces and cleaning tasks. From upholstery to hard floors, the adjustable settings and specialized tools ensure that users can achieve optimal results no matter the job at hand.

The Nilfisk-ALTO 46/53 also boasts noise reduction technology, making it suitable for use in noise-sensitive environments. Its low operational noise allows cleaning to occur without disturbing customers or staff, which is a major advantage for businesses operating during hours of high foot traffic.

In summary, the Nilfisk-ALTO 46/53 range combines powerful suction, advanced filtration, and user-friendly features into a single cleaning solution. Whether for commercial, industrial, or professional use, this vacuum cleaner stands out as a reliable option that meets a wide variety of cleaning needs while promoting efficiency and health.
Top Page Image Contents