Nilfisk-ALTO 46/53 manual Replacing the Dust Control Filter, Dust Flaps

Page 40

SERVICE INSTRUCTIONS

1/16"

 

SET DOOR FLAP

 

EVEN WITH FLOOR

P4488A

FIGURE 38

REPLACING THE DUST CONTROL FILTER

Change the filter panel when damage is evident.

1.Park the machine on a smooth level surface, turn the key switch to the “O” position and engage the parking brake.

2.Open the hopper compartment cover to gain access to the filter compartment.

3.Turn the latch on the hinged frame counterclockwise and lift the frame .

4.Remove the filter panel.

5.Install replacement filter, lower the hinged frame and engage the latch.

6.Lower the filter compartment cover.

DUST FLAPS

The dust flaps are very important to sweeping and dust control and are susceptible to damage and should be inspected daily and maintained in good condition.

CHECKING THE DUST FLAPS

The dust flaps are used on the wheel well, broom chamber and broom door. Inspect the flaps daily and replace any flap that shows signs of wear or deterioration. All flaps should be replaced when worn or damaged to the point that they can no longer perform their normal function. The adjustable flaps have slotted mounting holes to facilitate adjustment.

ADJUSTING THE DUST FLAPS

Adjust the flaps so there is a 1/8" to 1/16" gap between the floor and the bottom edge of the flaps. The rear flap adjustment is 1/16" (16 cm.) above the floor.

1.Park the machine on a smooth level surface and engage the parking brake.

2.Loosen the flap retaining screws and adjust the flap to clear the floor and leave a 1/16" to 1/8" gap.

3.Tighten flap-retaining screws while holding flap in position.

4.Drive the machine on a smooth surface and recheck the flaps for proper floor clearance.

1-40

American-Lincoln

 

ATS 46-53 Battery

Page 39 Page 41
Image 40
Page 39 Page 41
Contents American-Lincoln Technology Table of Contents American-Lincoln ATS 46/53 Battery Options Specifications Warranty SqueegeeTanks HopperMachine Dimensions Standard Hardware & Torque Values SAE GradeHydraulic Torque Requirements Hydraulic Torque RequirementsDECIMAL-METRIC Conversion Table DECIMAL-METRIC Conversion TableMachine Preparation Preparing the Machine for OperationSafety Instructions Read the Instruction BookSafety Instructions Safety Instructions Operation of Controls and Gauges Light Switch See FigureHorn Button See Figure KEY Switch See Figure FORWARD/REVERSE Switch See FigureCombination Battery Condition & Hour Meter Seat Position Adjustment See FigureFilter Shaker Switch To Engage the Safety ARMSide Broom Adjustment See figure Main Broom Adjustment See FigureSide Broom Lever Side Broom Lever See FigureScrub Deck Switch See Figure Dust Control Switch See FigureSqueegee Switch See Figure Solution Control See Figure NON-RECYCLING or Standard Scrubbing SystemRecycling or ESP & Autofil System To Disconnect Water HoseHopper Temperature Light Option Solution LOW LightRecovery High Light Charging System LightBrake Pedal Foot Pedal AcceleratorParking Brake Hopper Lift Lever See Figure Hopper Dump Door Lever See FigureC1702batt Turn Signal 4-Way Option See Figure BACK-UP Alarm Switch Option See FigureC1719 C1718Filter Panel Latch See Figure Front Cover Latch See FigureHydraulic Reservoir Level Sight GaugeHydraulic Reservoir Level Sight Gauge Main Broom Compartment Doors See FigureHopper Door Lever See Figure Hopper Filter Cover See FigureRecycling System Detergent LOW ON/OFF Switch ESP System Operating InstructionsScrubbing System HOW IT Works Solution Tank Detergent Tank RecoveryNON-RECYCLING or Standard Scrubbing System HOW IT Works Recovery or ESP and Autofil System HOW IT Works OrificeCheck Floor ContactOperating Instructions POST-OPERATION Checklist Battery Charging InstructionsStorage for BATTERY-POWERED Machines Emptying the Debris HopperHelpful Hints for Cleaning Operation Main AisleService Chart Service ChartHour Weekly Maintenance Checklist Hour Maintenance ChecklistFront Service Precautions Service PrecautionsService Instructions Side Broom Service Replacing the Side BroomHopper Service Cleaning the HopperCleaning the Dust Control Filter Checking the Hopper SealsReplacing the Dust Control Filter Dust FlapsBrake Service Adjusting the Brake PedalAdjusting the Brakes BrakesGeneral Machine Maintenance Cleaning the Hydraulic SystemFill Hydraulic Reservoir Filling the Hydraulic ReservoirSolution LOW Warning Light Recovery High Warning LightBrush Latch Replacing the Scrub BrushAdjusting Casters Recycling Pump ESP SystemRecycling Pump Storage Rear SqueegeeBattery Parts List Legend Abbreviations ScrewsProblem Probable Cause Remedy General TroubleshootingCheck & repair. orSereplaceahC -.Lynn Ordering Parts Internet Alto Headquarters

46/53 specifications

The Nilfisk-ALTO 46/53 is a powerful and versatile range of professional vacuum cleaners designed to meet the demanding needs of various cleaning applications. Known for their efficiency and reliability, these models are ideal for both commercial and industrial environments. With a robust construction, the Nilfisk-ALTO 46/53 series is built to withstand the wear and tear of daily use.

One of the standout features of the Nilfisk-ALTO 46/53 is its impressive suction power. Equipped with high-efficiency motors, these vacuum cleaners ensure optimal performance while consuming less energy. This not only enhances productivity but also contributes to cost savings and environmental sustainability.

The design of the Nilfisk-ALTO 46/53 is user-friendly, featuring an ergonomic handle and lightweight construction that make it easy to maneuver in tight spaces. Its compact design does not compromise on the capacity, as the model comes with a generous tank size, allowing for extended cleaning sessions without frequent interruptions for disposal.

Another notable characteristic of the Nilfisk-ALTO 46/53 is its advanced filtration system. The vacuum includes a HEPA filter, which captures fine dust and allergens, ensuring a cleaner and healthier environment. This feature is particularly beneficial in settings where air quality is critical, such as hospitals and laboratories.

In terms of versatility, the Nilfisk-ALTO 46/53 is equipped with various accessories and attachments designed to tackle different surfaces and cleaning tasks. From upholstery to hard floors, the adjustable settings and specialized tools ensure that users can achieve optimal results no matter the job at hand.

The Nilfisk-ALTO 46/53 also boasts noise reduction technology, making it suitable for use in noise-sensitive environments. Its low operational noise allows cleaning to occur without disturbing customers or staff, which is a major advantage for businesses operating during hours of high foot traffic.

In summary, the Nilfisk-ALTO 46/53 range combines powerful suction, advanced filtration, and user-friendly features into a single cleaning solution. Whether for commercial, industrial, or professional use, this vacuum cleaner stands out as a reliable option that meets a wide variety of cleaning needs while promoting efficiency and health.
Top Page Image Contents