Nilfisk-ALTO 46/53 manual Side Broom Lever See Figure, Side Broom Adjustment See figure

Page 18

OPERATION OF CONTROLS AND GAUGES

SIDE

BROOM

LEVER

SIDE BROOM ADJUSTMENT

SIDE BROOM LEVER (See Figure 9)

The Side Broom Lever is located to the right of the instru- ment console. The handle pulled back and turned to the left, will raise the side broom and lock it into position.

To raise the side broom pull the lever back into the “UP” position.

To lower the side broom, move the lever out of the “UP” position and move it forward to the “DOWN” position.

NOTE

IF THE MAIN BROOM IS ENGAGED, THE SIDE BROOM WILL

AUTOMATICALLY ENGAGE WHEN LOWERED.

SIDE BROOM ADJUSTMENT (See figure 9)

The side broom lever has an adjustment for changing the sweep height to compensate for broom wear. The side broom adjustment is located under the right side of the instrument panel.

C1641batt

FIGURE 9

MAIN BROOM LEVER (See figure 10)

 

 

 

 

The main broom lever is located on the left side of the

 

 

instrument panel. The main broom lever has three posi-

 

 

tions and controls the main broom sweep height.

MAIN

 

To lower the main broom, grasp the lever and move it to

BROOM

 

the left out of the “UP” position, and place it in the

LEVER

 

“SWEEP” or “FLOAT” position.

 

 

 

 

The “SWEEP” position is used for normal sweeping and

 

 

should be used under most sweeping conditions (approxi-

 

 

mately 2” broom pattern).

 

 

The “FLOAT” position is used for sweeping very uneven

 

 

surfaces only. Using the float position will cause premature

 

 

wear on the main broom if used under normal operating

 

 

conditions for extended periods of time (approximately 4”

MAIN

 

broom pattern).

 

CIRCUTBREAKERS

BROOM

 

NOTE

ADJUSTMENT

 

The Main Broom will automatically engage when lowered to

 

 

the sweep position or the float position. The hopper must be

 

 

completely closed.

 

 

MAIN BROOM ADJUSTMENT (See Figure 10)

 

 

The main broom lever has an adjustment for changing the

 

 

sweep height to compensate for broom wear. The main

C1642-1batt

FIGURE 10

broom adjustment is located under the left side of the

instrument panel.

 

 

1-18

 

American-Lincoln

 

 

ATS 46-53 Battery

Page 17 Page 19
Image 18
Page 17 Page 19
Contents American-Lincoln Technology Table of Contents American-Lincoln ATS 46/53 Battery Options Specifications Tanks WarrantySqueegee HopperMachine Dimensions Standard Hardware & Torque Values SAE GradeHydraulic Torque Requirements Hydraulic Torque RequirementsDECIMAL-METRIC Conversion Table DECIMAL-METRIC Conversion TableMachine Preparation Preparing the Machine for OperationSafety Instructions Read the Instruction BookSafety Instructions Safety Instructions Light Switch See Figure Operation of Controls and GaugesHorn Button See Figure Combination Battery Condition & Hour Meter KEY Switch See FigureFORWARD/REVERSE Switch See Figure Seat Position Adjustment See FigureFilter Shaker Switch To Engage the Safety ARMSide Broom Lever Side Broom Adjustment See figureMain Broom Adjustment See Figure Side Broom Lever See FigureDust Control Switch See Figure Scrub Deck Switch See FigureSqueegee Switch See Figure Recycling or ESP & Autofil System Solution Control See FigureNON-RECYCLING or Standard Scrubbing System To Disconnect Water HoseRecovery High Light Hopper Temperature Light OptionSolution LOW Light Charging System LightFoot Pedal Accelerator Brake PedalParking Brake Hopper Lift Lever See Figure Hopper Dump Door Lever See FigureC1702batt Turn Signal 4-Way Option See Figure BACK-UP Alarm Switch Option See FigureFilter Panel Latch See Figure C1719C1718 Front Cover Latch See FigureHydraulic Reservoir Level Sight Gauge Hydraulic ReservoirLevel Sight Gauge Main Broom Compartment Doors See FigureHopper Door Lever See Figure Hopper Filter Cover See FigureRecycling System Detergent LOW ON/OFF Switch ESP System Operating InstructionsSolution Tank Detergent Tank Recovery Scrubbing System HOW IT WorksNON-RECYCLING or Standard Scrubbing System HOW IT Works Check Recovery or ESP and Autofil System HOW IT WorksOrifice Floor ContactOperating Instructions Storage for BATTERY-POWERED Machines POST-OPERATION ChecklistBattery Charging Instructions Emptying the Debris HopperHelpful Hints for Cleaning Operation Main AisleHour Weekly Maintenance Checklist Service ChartService Chart Hour Maintenance ChecklistFront Service Precautions Service PrecautionsService Instructions Side Broom Service Replacing the Side BroomCleaning the Dust Control Filter Hopper ServiceCleaning the Hopper Checking the Hopper SealsReplacing the Dust Control Filter Dust FlapsAdjusting the Brakes Brake ServiceAdjusting the Brake Pedal BrakesFill Hydraulic Reservoir General Machine MaintenanceCleaning the Hydraulic System Filling the Hydraulic ReservoirBrush Latch Solution LOW Warning LightRecovery High Warning Light Replacing the Scrub BrushRecycling Pump Storage Adjusting CastersRecycling Pump ESP System Rear SqueegeeBattery Parts List Legend Abbreviations ScrewsProblem Probable Cause Remedy General TroubleshootingCheck & repair. orSereplaceahC -.Lynn Ordering Parts Internet Alto Headquarters

46/53 specifications

The Nilfisk-ALTO 46/53 is a powerful and versatile range of professional vacuum cleaners designed to meet the demanding needs of various cleaning applications. Known for their efficiency and reliability, these models are ideal for both commercial and industrial environments. With a robust construction, the Nilfisk-ALTO 46/53 series is built to withstand the wear and tear of daily use.

One of the standout features of the Nilfisk-ALTO 46/53 is its impressive suction power. Equipped with high-efficiency motors, these vacuum cleaners ensure optimal performance while consuming less energy. This not only enhances productivity but also contributes to cost savings and environmental sustainability.

The design of the Nilfisk-ALTO 46/53 is user-friendly, featuring an ergonomic handle and lightweight construction that make it easy to maneuver in tight spaces. Its compact design does not compromise on the capacity, as the model comes with a generous tank size, allowing for extended cleaning sessions without frequent interruptions for disposal.

Another notable characteristic of the Nilfisk-ALTO 46/53 is its advanced filtration system. The vacuum includes a HEPA filter, which captures fine dust and allergens, ensuring a cleaner and healthier environment. This feature is particularly beneficial in settings where air quality is critical, such as hospitals and laboratories.

In terms of versatility, the Nilfisk-ALTO 46/53 is equipped with various accessories and attachments designed to tackle different surfaces and cleaning tasks. From upholstery to hard floors, the adjustable settings and specialized tools ensure that users can achieve optimal results no matter the job at hand.

The Nilfisk-ALTO 46/53 also boasts noise reduction technology, making it suitable for use in noise-sensitive environments. Its low operational noise allows cleaning to occur without disturbing customers or staff, which is a major advantage for businesses operating during hours of high foot traffic.

In summary, the Nilfisk-ALTO 46/53 range combines powerful suction, advanced filtration, and user-friendly features into a single cleaning solution. Whether for commercial, industrial, or professional use, this vacuum cleaner stands out as a reliable option that meets a wide variety of cleaning needs while promoting efficiency and health.
Top Page Image Contents