Nilfisk-ALTO 46/53 manual Side Broom Service, Replacing the Side Broom

Page 38

SERVICE INSTRUCTIONS

SIDE BROOM SERVICE

LOCK PIN

FLOOR

CONTACT

AREA

10

FORWARD

3

C-0740

 

SIDE

 

BROOM

C0740

FIGURE 36

SIDE BROOM

The Side Broom sweeping angle is not adjustable. However, the height of the side brooms can be adjusted to compensate as the broom becomes worn from use. Always check and adjust the sweep pattern after changing the side broom.

CHECKING THE SIDE BROOM SWEEP PATTERN

ADJUSTING THE SIDE BROOM HEIGHT

Turn the side broom adjustment knob to change the side broom sweep height. Recheck for proper sweep pattern after adjustment.

-Turn the adjustment knob counterclockwise to INCREASE the sweep pattern width. -Turn the adjustment knob clockwise to DECREASE the sweep pattern width.

SIDE BROOM SERVICE

1.Park the machine on a smooth level surface.

2.Place the side broom lever in the “DOWN” position.

3.Move the brooms control lever to the “ON” position.

4.While staying in place allow the side broom to sweep for a short period of time. (Allow enough time for the side brooms to leave a clean footprint on the floor).

5.Place the side broom lever in the “UP” position.

6.Move the brooms control lever to the “OFF” position.

7.Back the sweeper away from the area where the pattern was left.

8.Turn the key switch to the “OFF” position and engage the parking brake.

9.Leave the operator’s compartment and check the pattern to determine the floor contact area.

10.Determine if adjustment to the side brooms height is necessary by examining the floor contact area. The broom should contact the floor as shown in Figure 36. Adjust the side broom height if the contact area on the floor does not match the diagram.

REPLACING THE SIDE BROOM

Change the side brooms when the bristles become worn to less than 3 inches length.

1.Park the machine on a smooth level surface, turn key switch to “O” Position and engage parking brake.

2.Place the side brooms lever in the “UP” position.

3.Remove the lock pin that holds the broom flange to the motor shaft.

4.Disassemble the flange from the broom by removing the screws that hold the flange to the broom.

5.Assemble the flange to the replacement broom and fasten using the hardware removed.

6.Install the replacement broom on the shaft and insert the lockpin.

1-38

American-Lincoln

 

ATS 46-53 Battery

Page 37 Page 39
Image 38
Page 37 Page 39
Contents American-Lincoln Technology Table of Contents American-Lincoln ATS 46/53 Battery Options Specifications Tanks WarrantySqueegee HopperMachine Dimensions Standard Hardware & Torque Values SAE GradeHydraulic Torque Requirements Hydraulic Torque RequirementsDECIMAL-METRIC Conversion Table DECIMAL-METRIC Conversion TableMachine Preparation Preparing the Machine for OperationSafety Instructions Read the Instruction BookSafety Instructions Safety Instructions Horn Button See Figure Light Switch See FigureOperation of Controls and Gauges Combination Battery Condition & Hour Meter KEY Switch See FigureFORWARD/REVERSE Switch See Figure Seat Position Adjustment See FigureFilter Shaker Switch To Engage the Safety ARMSide Broom Lever Side Broom Adjustment See figureMain Broom Adjustment See Figure Side Broom Lever See FigureSqueegee Switch See Figure Dust Control Switch See FigureScrub Deck Switch See Figure Recycling or ESP & Autofil System Solution Control See FigureNON-RECYCLING or Standard Scrubbing System To Disconnect Water HoseRecovery High Light Hopper Temperature Light OptionSolution LOW Light Charging System LightParking Brake Foot Pedal AcceleratorBrake Pedal Hopper Lift Lever See Figure Hopper Dump Door Lever See FigureC1702batt Turn Signal 4-Way Option See Figure BACK-UP Alarm Switch Option See FigureFilter Panel Latch See Figure C1719C1718 Front Cover Latch See FigureHydraulic Reservoir Level Sight Gauge Hydraulic ReservoirLevel Sight Gauge Main Broom Compartment Doors See FigureHopper Door Lever See Figure Hopper Filter Cover See FigureRecycling System Detergent LOW ON/OFF Switch ESP System Operating InstructionsNON-RECYCLING or Standard Scrubbing System HOW IT Works Solution Tank Detergent Tank RecoveryScrubbing System HOW IT Works Check Recovery or ESP and Autofil System HOW IT WorksOrifice Floor ContactOperating Instructions Storage for BATTERY-POWERED Machines POST-OPERATION ChecklistBattery Charging Instructions Emptying the Debris HopperHelpful Hints for Cleaning Operation Main AisleHour Weekly Maintenance Checklist Service ChartService Chart Hour Maintenance ChecklistFront Service Precautions Service PrecautionsService Instructions Side Broom Service Replacing the Side BroomCleaning the Dust Control Filter Hopper ServiceCleaning the Hopper Checking the Hopper SealsReplacing the Dust Control Filter Dust FlapsAdjusting the Brakes Brake ServiceAdjusting the Brake Pedal BrakesFill Hydraulic Reservoir General Machine MaintenanceCleaning the Hydraulic System Filling the Hydraulic ReservoirBrush Latch Solution LOW Warning LightRecovery High Warning Light Replacing the Scrub BrushRecycling Pump Storage Adjusting CastersRecycling Pump ESP System Rear SqueegeeBattery Parts List Legend Abbreviations ScrewsProblem Probable Cause Remedy General TroubleshootingCheck & repair. orSereplaceahC -.Lynn Ordering Parts Internet Alto Headquarters

46/53 specifications

The Nilfisk-ALTO 46/53 is a powerful and versatile range of professional vacuum cleaners designed to meet the demanding needs of various cleaning applications. Known for their efficiency and reliability, these models are ideal for both commercial and industrial environments. With a robust construction, the Nilfisk-ALTO 46/53 series is built to withstand the wear and tear of daily use.

One of the standout features of the Nilfisk-ALTO 46/53 is its impressive suction power. Equipped with high-efficiency motors, these vacuum cleaners ensure optimal performance while consuming less energy. This not only enhances productivity but also contributes to cost savings and environmental sustainability.

The design of the Nilfisk-ALTO 46/53 is user-friendly, featuring an ergonomic handle and lightweight construction that make it easy to maneuver in tight spaces. Its compact design does not compromise on the capacity, as the model comes with a generous tank size, allowing for extended cleaning sessions without frequent interruptions for disposal.

Another notable characteristic of the Nilfisk-ALTO 46/53 is its advanced filtration system. The vacuum includes a HEPA filter, which captures fine dust and allergens, ensuring a cleaner and healthier environment. This feature is particularly beneficial in settings where air quality is critical, such as hospitals and laboratories.

In terms of versatility, the Nilfisk-ALTO 46/53 is equipped with various accessories and attachments designed to tackle different surfaces and cleaning tasks. From upholstery to hard floors, the adjustable settings and specialized tools ensure that users can achieve optimal results no matter the job at hand.

The Nilfisk-ALTO 46/53 also boasts noise reduction technology, making it suitable for use in noise-sensitive environments. Its low operational noise allows cleaning to occur without disturbing customers or staff, which is a major advantage for businesses operating during hours of high foot traffic.

In summary, the Nilfisk-ALTO 46/53 range combines powerful suction, advanced filtration, and user-friendly features into a single cleaning solution. Whether for commercial, industrial, or professional use, this vacuum cleaner stands out as a reliable option that meets a wide variety of cleaning needs while promoting efficiency and health.
Top Page Image Contents