Nilfisk-ALTO 46/53 manual Hydraulic Reservoir Level Sight Gauge

Page 26

OPERATION OF CONTROLS AND GAUGES

HYDRAULIC RESERVOIR

HYDRAULIC RESERVOIR LEVEL SIGHT GAUGE

(See Figure 24)

LEVEL SIGHT GAUGE

The sight gauge is located on the inside of the hydraulic

 

 

reservoir in the engine compartment. The sight gauge is

 

used to indicate the level of fluid in the reservoir. The fluid

 

level must be visible in the sight gauge when the hopper is

 

in the down position.

 

 

MAIN BROOM COMPARTMENT DOORS (See Figure 25)

 

 

The main broom compartment doors are located behind the

 

 

front tires on both sides of the machine. The doors provide

 

 

access to the main broom for service or inspection.

 

 

WARNING

 

 

Operate Only When Lids, Doors, And Access Panels Are

C1730

FIGURE 24

Securely Closed.

 

 

Open the right side door to remove or replace the main

 

 

broom. The right side door is an integral part of the main

 

 

broom drive system and must be closed for operation.

 

MAIN BROOM

Open the left side broom door for inspection. Check the

 

drive hub for banding and shrink-wrap which have a

 

COMPARTMENT

 

tendency to get tangled in the broom driver. To open the

 

LATCH

 

main broom door, reach inside the hole in the door and lift

 

 

 

 

up on the latch handle. The door latch will automatically

 

PULL UP

engage when the door is closed.

 

 

 

TO OPEN

NOTE

 

 

C0729A/9707

 

Side squeegees mount on doors and the scrub deck must

 

be lowered to slide the doors and squeegees into place.

 

 

 

 

NOTE

 

 

For proper function of side squeegees, side squeegees must

C0729A

FIGURE 25

be positioned so the lift strap is above the scrub deck lift

 

 

brackets. Damage to the side squeegees could occur if not

 

 

in the correct position.

 

 

SEAT COMPARTMENT COVER & PROP LATCH

 

 

(See Figure 26)

 

 

The seat compartment cover opens to allow easy access to

 

 

various components that will need to be inspected or

 

 

serviced periodically. The cover opens forward and has a

 

 

safety latch to hold the cover in the open position.

 

 

On battery-powered machines, the compartment below the

 

 

seat contains the hydraulic pump motor and reservoir.

 

 

The seat compartment latch is located under the seat

 

 

compartment cover and is used to hold the cover open.

 

 

To hold the seat compartment cover open, lift the cover and

C1699a-batt

 

rotate the latch.

C1699a-batt

FIGURE 26

 

1-26

 

American-Lincoln

 

 

ATS 46-53 Battery

Page 25 Page 27
Image 26
Page 25 Page 27
Contents American-Lincoln Technology Table of Contents American-Lincoln ATS 46/53 Battery Options Specifications Tanks WarrantySqueegee HopperMachine Dimensions Standard Hardware & Torque Values SAE GradeHydraulic Torque Requirements Hydraulic Torque RequirementsDECIMAL-METRIC Conversion Table DECIMAL-METRIC Conversion TableMachine Preparation Preparing the Machine for OperationSafety Instructions Read the Instruction BookSafety Instructions Safety Instructions Horn Button See Figure Light Switch See FigureOperation of Controls and Gauges Combination Battery Condition & Hour Meter KEY Switch See FigureFORWARD/REVERSE Switch See Figure Seat Position Adjustment See FigureFilter Shaker Switch To Engage the Safety ARMSide Broom Lever Side Broom Adjustment See figureMain Broom Adjustment See Figure Side Broom Lever See FigureSqueegee Switch See Figure Dust Control Switch See FigureScrub Deck Switch See Figure Recycling or ESP & Autofil System Solution Control See FigureNON-RECYCLING or Standard Scrubbing System To Disconnect Water HoseRecovery High Light Hopper Temperature Light OptionSolution LOW Light Charging System LightParking Brake Foot Pedal AcceleratorBrake Pedal Hopper Lift Lever See Figure Hopper Dump Door Lever See FigureC1702batt Turn Signal 4-Way Option See Figure BACK-UP Alarm Switch Option See FigureFilter Panel Latch See Figure C1719C1718 Front Cover Latch See FigureHydraulic Reservoir Level Sight Gauge Hydraulic ReservoirLevel Sight Gauge Main Broom Compartment Doors See FigureHopper Door Lever See Figure Hopper Filter Cover See FigureRecycling System Detergent LOW ON/OFF Switch ESP System Operating InstructionsNON-RECYCLING or Standard Scrubbing System HOW IT Works Solution Tank Detergent Tank RecoveryScrubbing System HOW IT Works Check Recovery or ESP and Autofil System HOW IT WorksOrifice Floor ContactOperating Instructions Storage for BATTERY-POWERED Machines POST-OPERATION ChecklistBattery Charging Instructions Emptying the Debris HopperHelpful Hints for Cleaning Operation Main AisleHour Weekly Maintenance Checklist Service ChartService Chart Hour Maintenance ChecklistFront Service Precautions Service PrecautionsService Instructions Side Broom Service Replacing the Side BroomCleaning the Dust Control Filter Hopper ServiceCleaning the Hopper Checking the Hopper SealsReplacing the Dust Control Filter Dust FlapsAdjusting the Brakes Brake ServiceAdjusting the Brake Pedal BrakesFill Hydraulic Reservoir General Machine MaintenanceCleaning the Hydraulic System Filling the Hydraulic ReservoirBrush Latch Solution LOW Warning LightRecovery High Warning Light Replacing the Scrub BrushRecycling Pump Storage Adjusting CastersRecycling Pump ESP System Rear SqueegeeBattery Parts List Legend Abbreviations ScrewsProblem Probable Cause Remedy General TroubleshootingCheck & repair. orSereplaceahC -.Lynn Ordering Parts Internet Alto Headquarters

46/53 specifications

The Nilfisk-ALTO 46/53 is a powerful and versatile range of professional vacuum cleaners designed to meet the demanding needs of various cleaning applications. Known for their efficiency and reliability, these models are ideal for both commercial and industrial environments. With a robust construction, the Nilfisk-ALTO 46/53 series is built to withstand the wear and tear of daily use.

One of the standout features of the Nilfisk-ALTO 46/53 is its impressive suction power. Equipped with high-efficiency motors, these vacuum cleaners ensure optimal performance while consuming less energy. This not only enhances productivity but also contributes to cost savings and environmental sustainability.

The design of the Nilfisk-ALTO 46/53 is user-friendly, featuring an ergonomic handle and lightweight construction that make it easy to maneuver in tight spaces. Its compact design does not compromise on the capacity, as the model comes with a generous tank size, allowing for extended cleaning sessions without frequent interruptions for disposal.

Another notable characteristic of the Nilfisk-ALTO 46/53 is its advanced filtration system. The vacuum includes a HEPA filter, which captures fine dust and allergens, ensuring a cleaner and healthier environment. This feature is particularly beneficial in settings where air quality is critical, such as hospitals and laboratories.

In terms of versatility, the Nilfisk-ALTO 46/53 is equipped with various accessories and attachments designed to tackle different surfaces and cleaning tasks. From upholstery to hard floors, the adjustable settings and specialized tools ensure that users can achieve optimal results no matter the job at hand.

The Nilfisk-ALTO 46/53 also boasts noise reduction technology, making it suitable for use in noise-sensitive environments. Its low operational noise allows cleaning to occur without disturbing customers or staff, which is a major advantage for businesses operating during hours of high foot traffic.

In summary, the Nilfisk-ALTO 46/53 range combines powerful suction, advanced filtration, and user-friendly features into a single cleaning solution. Whether for commercial, industrial, or professional use, this vacuum cleaner stands out as a reliable option that meets a wide variety of cleaning needs while promoting efficiency and health.
Top Page Image Contents