Nilfisk-ALTO MX 107 C operating instructions Operation

Page 5

Refer to the drawings on the previous page

OPERATION

1Inspect the machine, hoses, and cleaning tools for cleanliness and completeness.

2Fill the solution tank with water. Using warm water may be a benefit in cleaning effectiveness, but do not use hot water (above 54 °C / 130 °F) in the tank.

3Plug in the power cord.

4Add liquid cleaning solution, with a pH of between 6 and 9, to the solution tank. Mix it well.

5Attach the spray hose to the solution quick disconnect and the vacuum hose to the hose barb on the recovery tank. Attach the other ends of the hoses to the cleaning tool.

6Turn on the pump (2). Turn on the vacuum (1).

7Begin cleaning using the correct hoses and tool.

8Use defoamer in the recovery tank any time foaming occurs.

9Monitor the water level in the solution tank. Do not let the pump run dry.

10When the solution tank gets low, turn both the pump and the vacuum off, fill the solution tank, empty and clean the recovery tank.

11When finished with the job, remove any unused solution from the solution tank, and run a few gallons of clean water through the system. Drain the recovery tank by placing a bucket or drain under the drain gate.

CAUTION: if foam or water comes out the vacuum exhaust, turn the machine off immediately.

CAUTION: to avoid vacuum motor damage, always use a defoamer any time foam is present.

BALL FLOAT VACUUM SHUT-OFF

Prior to using the machine, always check that the float filter is clean and the ball can travel freely. When the recovery tank is full, the ball float will rise and will shut off the vacuum flow to prevent any more water from entering the tank. When this occurs, turn off the vacuum and empty the recovery tank.

NOTE: if foam is present, or if the ball float is prevented from rising, the float will not be able to stop the air flow, and the tank may over fill. Water damage to the vacuum motors is not covered by warranty.

600101071REVA

Image 5
Contents Extractor To reduce the risk of fire, electric shock, or injury Important Safety InstructionsInspection Switch Plate Operation MX 107 C MX 107 C Extractor Extractor Extracteur Informations Mode D’EMPLOIConsignes DE Sécurité Importantes Inspection Plaque D’INTERRUPTEUR Fonctionnement Arrêt PAR Flotteur DE L’ASPIRATIONMX 107 C Élément QTÉ Extracteur MX 107 CAutre ExtracteurDébranchez Toujours LA Machine Avant DE Déconnecter OU DEInformación E Instrucciones DE USO ExtractorInstrucciones DE Seguridad Importantes ¡ADVERTENCIAMantenimiento InspecciónSoluciones DE Limpieza Placa DE Interruptores Funcionamiento Desconexión DE LA Aspiración POR EL Flotador DE BolaMX 107 C Descripción Elemento CTDExtractor Este ProblemaSI SE Produce Compruebe LO SiguienteInformazioni E Istruzioni PER ’USO EstrattoreImportanti Norme DI Sicurezza AvvertenzaManutenzione IspezioneSoluzioni PER LA Pulizia Piastra Interruttori Funzionamento Arresto DELL’ASPIRATORE CON Galleggiante a SferaMX 107 C QTÀ Codice Parte Descrizione Estrattore MX 107 CAltro Problema Azione CorrettivaEstrattore Allgemeine Hinweise UND Bedienungsanleitung ExtraktionsgerätWichtige Sicherheitshinweise WarnungWartung SichtprüfungReinigungsmittel = Saugmotor EIN-/AUSSCHALTER = Pumpe EIN-/AUSSCHALTER SchalttafelInbetriebnahme Schwimmerabschaltung Saugmotor OFFMX 107 C Beschreibung Artikel StckBEI Diesen Zuständen ÜBERPRÜFEN, OB ExtraktionsgerätSonstiges Information Användarinstruktioner ExtraktorViktiga Säkerhetsanvisningar VarningUnderhåll InspektionRengöringsmedel = Vakuum PÅ/AV-OMKOPPLARE = Pump PÅ/AV-OMKOPPLARE OmkopplarplattaAnvändning Vakuumavstängning MED KulflottörMX 107 C Artikel Antal ART. NR Beskrivning MX 107 C ExtraktorRengör Alla Filter ExtraktorÖvrigt OM Detta InträffarYikama Makýnesý Uyari Aþaðidaký Býlgýlerý Kaydedýp Saklayin Anahtar Plakasi Küresel Þamandirali Vakum Kesme MX 107 C MX 107 C Yikama Makýnesý Yikama Makýnesý Экстрактор Важные Правила Техники Безопасности ВниманиеПроверка Щиток Переключателей Шаровой Поплавковый Отсекающий Клапан Всасывающего Агрегата 600101071REVA Пункт К-ВО Детали Описание MX 107 C ЭкстракторКомпонентов Сети Перед Отключением ИЛИПодключением Проводов ИЛИ

MX 107 C specifications

The Nilfisk-ALTO MX 107 C is a high-performance wet and dry vacuum cleaner designed primarily for commercial and industrial use. Known for its robust construction and outstanding suction power, this machine excels in maintaining cleanliness in a variety of environments, including workshops, construction sites, and large facilities.

One of the standout features of the MX 107 C is its powerful motor, which delivers an impressive suction performance that effectively picks up both solid debris and liquids. This versatility makes it an excellent choice for tasks ranging from general clean-up to more challenging spills. The vacuum has a generous tank capacity, allowing for extended cleaning sessions without frequent emptying, which enhances efficiency and productivity.

The MX 107 C is designed with user comfort in mind. Its ergonomic handle and lightweight design facilitate easy maneuverability, even in tight spaces. Additionally, the machine features a compact footprint, enabling it to be stored conveniently in various locations without occupying excessive space. The vacuum comes equipped with a range of accessories, including different nozzle options and brush heads, which cater to different cleaning tasks and surfaces.

In terms of technology, the Nilfisk-ALTO MX 107 C incorporates advanced filtration systems to ensure that dust and allergens are effectively captured. The filters are designed for long-lasting performance, reducing the need for frequent replacements and maintenance. This feature not only improves air quality but also protects the motor from dust and debris, thereby enhancing the vacuum's longevity.

Another characteristic of the MX 107 C is its noise reduction technology, which allows for quieter operation without compromising suction power. This makes it an ideal choice for environments where noise levels need to be minimized, such as schools, hospitals, and office buildings.

Overall, the Nilfisk-ALTO MX 107 C combines powerful performance with user-friendly features, making it a popular choice for professionals and businesses looking for an efficient and reliable wet and dry vacuum cleaning solution. With its focus on quality and performance, the MX 107 C stands out as a robust and versatile machine that can handle the toughest cleaning challenges.