Nilfisk-ALTO 343E After Using the Machine, Recovery Tank Removal, Machine Long Inactivity

Page 51

USER MANUAL

ENGLISH

AFTER USING THE MACHINE

After working, before leaving the machine:

1.Remove the brush/pad-holder as follows:

•With the brush/pad-holder lifted, turn the brush/pad-holder switch (52) to “I” and, after a few seconds, back to “0”, thus releasing the brush/pad-holder.

2.Disconnect the power supply cable (21) from the electrical mains and place it on the holder.

3.Empty the tanks (26 and 27) as shown in the previous paragraph.

4.Perform the daily maintenance procedures (see the Maintenance chapter).

5.Store the machine in a clean and dry place, with the brush/pad-holder and the squeegee lifted or removed.

RECOVERY TANK REMOVAL

To perform check and maintenance procedures, it may be necessary to remove the recovery tank (26) as shown below.

1.Empty the recovery tank (26) as shown in the relevant paragraph.

2.Drive the machine on a level floor.

3.Make sure that the power supply cable (21) is disconnected from the electrical mains.

4.Disconnect the vacuum hose (22) from the squeegee (11).

5.Disconnect the recovery water drain hose (16) from the bracket (17).

6.Open the cover (6).

7.Grasp the recovery tank (A, Fig. 3) in the area (B) and slightly raise it.

8.Disconnect the vacuum hose (C) from the tank, then remove the tank (A) with the hoses (D) and (E).

B

C

A

E

D

Figure 3

S311229A

MACHINE LONG INACTIVITY

If the machine is not going to be used for more than 30 days, proceed as follows:

1.Perform the procedures shown in After Using the Machine paragraph.

2.Store the machine in a clean and dry place.

FIRST PERIOD OF USE

After the first 8 hours, check the machine fastening and connecting parts for proper tightening. Check the visible parts for integrity and leakage.

909 6315 000(4)2009-11 A

SCRUBTEC 343E

13

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Scrubtec 343E Scrubtec 343E Einleitung InhaltsverzeichnisEinleitung Sicherheit AUSPACKEN/LIEFERUNGAllgemeine Hinweise Deutsch Geräteaufbau Gerätebeschreibung909 6315 00042009-11 a Geräteaufbau FortsetzungAllgemein Bedienpult UND BedienelementeZUBEHÖR/SONDERAUSSTATTUNG Technische DatenFarbcodes SchaltplanVOR DEM Einschalten DES Geräts BetriebGerät abstellen Gerät Einschalten UND AbstellenGerät in Betrieb WASCHEN/TROCKNEN Gerät einschaltenReinigungslösungstank entleeren TRANSPORT/PARKEN DES GerätsTanks Entleeren Schmutzwassertank entleerenErste Betriebszeit Nach DER GerätebenutzungSchmutzwassertank Abnehmen Lange Stilllegung DES GerätsWöchentlich Halbjährlich Jährlich WartungÜbersichtstabelle Planmässige Wartung ArbeitsvorgangSauglippengummis Überprüfen UND Austauschen Sauglippe ReinigenTanks UND Ansauggitter Reinigen Bürste ReinigenVorschubgeschwindigkeit DES Geräts Einstellen Reinigungslösungsfilter ReinigenFehlersuche VerschrottungStörung Mögliche Ursache Abhilfe Introduction Table DES MatieresIntroduction Securite Deballage / LivraisonInstructions Generales Français Structure DE LA Machine Description DE LA MachineStructure DE LA Machine suite Caractéristiques générales Accessoires / OptionsTableau DE Bord Caracteristiques TechniquesSchema Electrique LégendeCodes des couleurs Avant LA Mise EN Marche DE LA Machine UtilisationArrêt de la machine Mise EN Marche ET Arret DE LA MachineMachine AU Travail Lavage / Sechage Mise en marche de la machineVidange du réservoir de l’eau de récupération Vidange du réservoir de la solutionTransport / Stationnement DE LA Machine Vidange DES ReservoirsPremiere Periode D’UTILISATION Apres L’UTILISATION DE LA MachineDepose DU Reservoir DE L’EAU DE Recuperation Inactivite Prolongee DE LA MachineHebdomadaire EntretienPlan D’ENTRETIEN Programme Quotidienne ProcédureNettoyer l’embouchure comme indiqué au paragraphe précédent Nettoyage DE L’EMBOUCHURENettoyage DES Reservoirs ET DE LA Grille D’ASPIRATION Nettoyage DE LA BrosseReglage DE LA Vitesse D’AVANCE DE LA Machine Nettoyage DU Filtre DE LA SolutionDepistage DES Pannes Mise a LA FerrailleProblème Cause possible Remède Table of Contents Target Manual Purpose and ContentsHOW to Keep this Manual Declaration of Conformity Spare Parts and MaintenanceChanges and Improvements SafetySymbols UNPACKING/DELIVERYGeneral Instructions English Machine Structure Machine DescriptionMachine Structure Continues General ACCESSORIES/OPTIONSTechnical Data Control PanelWiring Diagram KeyColour codes Before Machine START-UP USEStarting the machine Machine speed adjustmentMachine Start and Stop Machine Operation SCRUBBING/DRYINGTank Emptying Recovery tank emptyingSolution tank emptying Machine TRANSPORT/PARKINGFirst Period of USE After Using the MachineRecovery Tank Removal Machine Long InactivityWeekly Every six Yearly MaintenanceScheduled Maintenance Table ProcedureSqueegee Blade Check and Replacement Squeegee CleaningTank and Vacuum Grid Cleaning Brush CleaningMachine Speed Adjustment Solution Filter CleaningTroubleshooting ScrappingTrouble Possible Cause Remedy Inleiding InhoudsopgaveInleiding Veiligheid Verpakking VERWIJDEREN/AFLEVERINGAlgemene Instructies Nederlands Opbouw VAN DE Machine Beschrijving VAN DE MachineOpbouw VAN DE Machine Vervolg Algemeen Accessoires / OptiesCONTROLE- EN Bedieningspaneel Technische EigenschappenKleurcodering Elektrisch SchemaVoor HET Starten VAN DE Machine GebruikDe machine stoppen DE Machine Starten EN StoppenMachine in Gebruik WASSEN/DROGEN Starten van de machineTank met reinigingsmiddel legen DE Machine TRANSPORTEREN/PARKERENDE Tanks Legen Tank met vuil water legenEerste Gebruiksperiode NA Gebruik VAN DE MachineDE Tank MET Vuil Water Verwijderen Lange Periode VAN StilstandWekelijks OnderhoudsschemaDagelijks, na Procedure OnderhoudControle EN Vervanging VAN DE Rubbers VAN DE Trekker Reiniging VAN DE TrekkerReiniging VAN DE Tanks EN VAN HET Aanzuigrooster Reiniging VAN DE BorstelAfstelling VAN DE Voorwaartse Beweging VAN DE Machine Reiniging VAN HET Filter VAN HET ReinigingsmiddelStoringen Lokaliseren VerwijderingProbleem Waarschijnlijke oorzaak Herstelactie Page Austria

343E specifications

The Nilfisk-ALTO 343E is a high-performance industrial vacuum cleaner designed to offer exceptional versatility and efficiency in various commercial and industrial cleaning applications. This model stands out for its robust build quality, advanced features, and user-friendly design, making it an ideal choice for businesses seeking effective solutions for dust and debris control.

One of the main features of the Nilfisk-ALTO 343E is its powerful motor which delivers strong suction capabilities. With a maximum airflow of up to 400 m³/h, this vacuum is capable of handling a wide range of materials, including dust, chips, and liquids. The machine is equipped with a two-stage turbine that ensures efficient performance while maintaining low noise levels, making it suitable for use in environments where noise reduction is essential.

The 343E incorporates an advanced filtration system that significantly enhances its performance. It features a robust polyester filter that effectively captures fine particles, ensuring cleaner air is released back into the environment. Additionally, the filter is easy to clean, thereby extending its lifespan and reducing maintenance costs. The vacuum also provides an optional HEPA filter, which is vital for environments that require high levels of air purity, such as healthcare facilities or laboratories.

Another characteristic that sets the Nilfisk-ALTO 343E apart is its user-friendly design. The vacuum cleaner is built with ergonomic considerations, featuring an adjustable handle and wheels that make maneuvering around tight spaces effortless. The lightweight design further enhances mobility, allowing operators to transport the machine with ease.

The Nilfisk-ALTO 343E is also equipped with a large-capacity collection tank that can hold up to 35 liters, enabling extended cleaning sessions without frequent emptying. The tank features a quick-release design for hassle-free disposal of collected debris. Furthermore, the vacuum is designed for versatility, accommodating various tools and accessories to adapt to different cleaning tasks.

In summary, the Nilfisk-ALTO 343E combines powerful suction, advanced filtration, user-centric design, and versatility, making it an indispensable tool in sectors such as manufacturing, construction, and maintenance. Its combination of efficiency and ease of use ensures that it meets the demanding needs of modern industrial cleaning requirements.
Top Page Image Contents