Integra RDV-1.1 instruction manual 12V Trigger, Supplied power cord should be connected here

Getting to Know the RDV-1.1—Continued

JVIDEO OUT VIDEO (30)

These two sockets output composite video and can be connected to a composite video input on a TV or projector.

KDIGITAL 1 AUDIO OUT (36, 38)

These sockets output digital audio and can be con- nected to the digital audio input on a hi-fi amp, AV receiver, surround sound decoder (Dolby Digital, DTS), or other component. There’s a coaxial output and an optical output.

LDIGITAL 2 AUDIO OUT (36, 38)

These sockets output digital audio and can be con- nected to the digital audio inputs on a hi-fi amp, AV receiver, surround sound decoder (Dolby Digital, DTS), or other component. There’s an AES/EBU (balanced XLR) output, a coaxial output, and an optical output.

MIR IN/OUT (41)

The IR IN socket can be used to connect a commer- cially available IR receiver, which can be used to pickup signals from the remote controller when the RDV-1.1 is located in another room, installed in a rack, or is out of range of the remote controller The IR OUT connector can be used to connect a commercially available IR emitter, which can be used to pass remote controller signals received by the IR IN along to other components.

N REMOTE CONTROL (40)

These (Remote Interactive) sockets can be con-

nected to the sockets on other Integra RESEARCH AV components for interactive con- trol.

To use you must make an analog audio connec- tion between the RDV-1.1 and your Integra RESEARCH AV receiver, even if they are already connected digitally.

OD.MIX AUDIO OUT (30, 31, 37)

These sockets output analog audio and can be con- nected to a stereo analog audio input on a TV, hi-fi amp, or other component. If the source audio is multichannel (Dolby Digital, DTS, DVD-Audio, SACD), they output a 2-channel downmix.

PFRONT, SURR 1, CENTER & SUBWOOFER AUDIO OUT (37)

These sockets output 5.1-channel analog audio and can be connected to a 5.1-channel analog audio input on an AV receiver, surround sound decoder (Dolby Pro Logic), or other component.

RSURR MODE (AUDIO OUT) switch (37)

This switch is used to set the surround output mode of the analog multichannel audio outputs. If you connect the SURR 2 outputs to a 7.1-channel AV receiver or amp, set this switch to 1+2. This reduces the output level by 3 dB. If you’re not using the SURR 2 outputs, set this switch to 1.

SHD VIDEO OUT COMPONENT 1 (31)

These BNC sockets output HD component video and can be connected to the HD component video input on an HDTV or projector. If you input HD video to the component VIDEO IN socket, this out- put should be connected to the HDTV or projector. When an SD video signal is fed to a VIDEO IN socket (component, S-Video, or composite), and the video input source is set to External, that video sig- nal is upconverted to progressive and output here. When an HD video signal is fed to the component VIDEO IN socket, and the video input source is set to External, that HD video signal is output here at the same resolution.

THD VIDEO OUT COMPONENT 2 (31)

These BNC sockets output HD component video and can be connected to the HD component video input on an HDTV or projector.

When an SD video signal is fed to a VIDEO IN socket (component, S-Video, or composite), and the video input source is set to External, that video sig- nal is upconverted to progressive and output here. When an HD video signal is fed to the component VIDEO IN socket, and the video input source is set to External, nothing is output by these sockets.

U12V TRIGGER IN

This socket can be connected to the 12-volt trigger output on an AV receiver or other component so that the RDV-1.1 can be turned on remotely.

VAC INLET (42)

The supplied power cord should be connected here.

WAV CONNECTOR (32)

This SCART socket outputs RGB video, S-Video, composite video, and analog stereo audio and can be connected to the SCART socket on a TV, projec- tor, or other component.

QSURR 2 AUDIO OUT (37)

These sockets output the same analog audio as the SURR1 outputs and can be connected to the analog surround back left and right inputs on a 7.1-channel AV receiver or other component. When using these sockets, the SURR MODE switch should be set to 1+2.

21