Integra RDV-1.1 instruction manual Troubleshooting, Symptom Possible cause Remedy

Troubleshooting

Symptom	Possible cause	Remedy
	The power cord is not connected.	Connect the power cord to a suitable wall outlet
		(page 42).
Can’t turn on the
		Turn off the RDV-1.1, wait five seconds, then try
RDV-1.1?	External interference is affecting the	turning it on again. If that fails, disconnect the
	RDV-1.1’s digital circuitry.	power cord from the wall outlet, wait five seconds,
		reconnect it, then try turning it on again.
The RDV-1.1 turns itself	The Auto power off function will turn the	The Auto power off function can be turned on or off
off when it’s not being	RDV-1.1 off automatically after 20 minutes of
		as required (page 85).
used?	inactivity.
	The wrong input source is selected on your TV.	On your TV, select the input to which the RDV-1.1
		is connected (pages 30, 31).
No picture?	The video cable is not connected properly.	Check the video cable and correct as necessary
		(pages 30, 31).
	Not all of the video outputs work with all disc	See page 27 for details on how the RDV-1.1 out-
	types and formats.	puts video from each output.
	The wrong input source is selected on your	On your hi-fi amp or AV receiver, select the input to
	hi-fi amp or AV receiver.	which the RDV-1.1 is connected (pages 36, 37).
	The audio cable is not connected properly.	Check the audio cable and correct as necessary
		(pages 36, 37).
No sound?
	Your hi-fi amp or AV receiver is turned off.	Turn on your hi-fi amp or AV receiver.
	The Digital Out settings are incorrect.	Check the Digital Out/Digital1 or Digital2 setting
		and correct as necessary (pages 75, 76).
	Not all of the analog and digital audio outputs	See page 28 for details on how the RDV-1.1 out-
	work with all disc types and formats.	puts audio from each output.
The picture distorts occa-	The disc is dirty.	Remove the disc and clean it (page 12).
	You’re using the Fast Forward or Fast Reverse	A little picture distortion may occur when using
sionally?
	function.	these functions. This is normal.
Picture instability or	The RDV-1.1 is connected to your TV via a	Connect the RDV-1.1 directly to your TV (pages
	VCR or other video equipment whose copy
noise?		30, 31).
	protection system is affecting the picture.
	No disc loaded.	Load a disc (page 46).
	The disc is incompatible.	Load only compatible discs (page 10).
	The disc is upside down.	Load the disc the correct way up (page 46).
Can’t start playback?	The disc is not centered in the disc tray.	Place the disc in the center of the disc tray
		(page 46).
	The disc is dirty.	Remove the disc and clean it (page 12).
	The disc supports parental lock and the Paren-	Turn off the Parental Lock function (page 84).
	tal Lock function is on.
Can’t watch the	The Priority Contents setting is set to	Set the Priority Contents setting to DVD-VIDEO
DVD-Video material on a
	DVD-AUDIO.	(page 85).
DVD-Audio disc?
Can’t play the multichan-	The SACD Audio Setup setting is not set to	Set the SACD Audio Setup setting to Multi ch Area
nel area of a hybrid
	Multi ch Area.	(page 81).
SACD?
	This is because the i.LINK Output Setting is
	set to Off. If the RDV-1.1 is properly con-	Set the i.LINK Output Setting to On (page 77).
SACD audio is not output	nected to an i.LINK component and an SACD
by the i.LINK sockets?	is loaded, the IEEE 1394 indicator will flash.
	The i.LINK cables are not connected properly.	Check the i.LINK connections and correct as nec-
		essary (page 34).

94