Controlling Other Components—Continued
On | On | Standby | TV | ||
|
|
| |||
|
|
| I | Input | |
| 1 |
| 2 | 3 | + |
|
|
|
|
| TV CH |
| 4 |
| 5 | 6 | - |
| 7 |
| 8 | 9 |
|
|
|
|
|
| TV VOL |
| +10 |
| 0 | Clear |
|
Search | Memory | Dimmer | Amp Input | ||
| S |
| M | D | Input |
|
|
| Amp Input |
| |
| DVD |
| V1 | V2 | V3 |
Mode |
|
| Mode |
|
|
DVD |
| Amp | VCR | TV | |
Zoom On |
|
|
| Picture Control | |
Audio |
|
| enu | M |
|
| opM | enu |
| ||
Sel |
| T |
|
|
|
| + |
|
|
|
|
| CH |
|
|
|
|
| Zoom |
| Enter |
| VOL |
| L Mode |
|
|
|
|
| - |
|
|
|
|
|
| R | eturn | p |
|
|
|
| Setu |
| |
Display |
|
|
| Muting | |
Last Memory |
| Step/Slow | Random | ||
Rec | LM |
|
|
| RD |
| Audio | Subtitle | Angle | Resolution | |
| Audio | Subtitle | Angle | Rsltn | |
| Repeat |
|
| Aspect | |
| Repeat |
|
| Aspect | |
Video Input | Video Off | Learning | |||
| V In |
| V Off | L1 | L 2 |
Open/Close |
|
|
|
| |
|
|
|
| L 3 | L 4 |
|
|
|
|
Learning the Commands of Other Remote Controllers
The
If you’ve entered a control code for a component (page 87) and certain buttons don’t work as expected, you can also use this function to program those buttons individually.
1 Point the remote controllers at each other, about 2 to 6 inches
|
|
|
|
|
|
|
| EM |
|
|
|
|
|
|
|
|
|
| ULOV | G |
|
|
|
|
|
|
|
|
|
| NITUM |
|
|
|
|
|
|
|
|
| EN | LE |
|
|
|
|
|
|
|
|
| TSETOT |
| VEL |
|
|
|
|
|
|
|
| L ES |
|
|
|
|
|
|
|
|
|
| HC |
|
|
| DC | TES |
|
|
|
|
|
|
| |
|
| ERP |
| DVD |
|
|
| EPAT |
| |
|
| ON | REN | UT |
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
| ROHP |
| PUO |
|
|
|
|
| ||
RED | OT | R |
| RG |
|
|
|
|
| |
USOM | REM | CELEESNUT |
| DC | CISD |
|
| |||
|
| ELS | E | DVD | V |
|
|
| ||
|
|
| TU | IDV |
|
|
|
| ||
|
| IMD |
| PNI PAT |
| 1- |
|
|
| |
|
|
| PE |
|
|
| OEID |
|
|
|
|
|
|
| REW |
|
|
|
|
| |
|
|
|
|
| OP |
|
|
|
|
|
RC-561DV
2 While holding down the [DVD], [Amp], [VCR], or [TV] Mode button, press the [On] button, and then release both buttons.
The MODE button and Tx/Learn indicator light up.
3 On the
The Tx/Learn indicator goes off while the button is being pressed, and comes back on again when it’s released.
Use the dedicated leaning
4 On the other remote controller, press and hold the button whose command you want to learn until the Tx/Learn indicator flashes.
If the command is learnt successfully, the Tx/ Learn indicator flashes slowly twice, and then the MODE button and Tx/Learn indicator remain lit. If the Tx/Learn indicator flashes quickly three times, the command has not been learnt, in which case you should try again from step 3.
If the Tx/Learn indicator flashes quickly six times, the remote controller’s memory is full and no more commands can be learnt.
5 To learn more new commands, repeat steps 3 and 4.
When you’ve finished, press the Mode button that you pressed in step 2.
To use the learnt command, select the relevant mode, and then press the button.
Notes:
•The following buttons cannot learn new commands: [LIGHT] and the [DVD], [Amp], [VCR], and [TV] Mode buttons.
•Learning mode is cancelled automatically if you don’t press any buttons for 30 seconds.
•The
•To program a button that has already learnt a com- mand, repeat this procedure. The previously learnt command will be overwritten.
•Like most remote controllers, the
•When the remote controller’s batteries expire, all learnt commands may be lost and will have to be learnt all over again, so keep your other remote controllers in a safe place.
92