Integra DTR-6.4/5.4 Configuring the speakers DTR-5.4, Calibrating the speaker levels

Page 55
Configuring the speakers (DTR-5.4)

Configuring the speakers (DTR-5.4)

Calibrating the speaker levels

Use this menu to set the volume for each speaker so that each volume is heard by the listener at the same level. This is especially important for speaker layouts where the left and right speakers are at different distances or in asymmetrical positions due to room designs and configurations. These settings and the distance settings performed in the Speaker Distance menu are vital to create the proper sound space and dynamics.

Note:

The speaker level settings here are not effective for multi-channel input sources. To adjust the speaker levels for multi-channel input sources, you will need to use the CH Sel, Level 2. Press the Test button to complete, and Level the procedure. buttons on the remote controller.

1. Use the Manual background and Manual background cursor buttons to select “4. Level Calibration” on the main menu and then press the ENTER button.

The “Level Calibration” menu appears.

Press the Setup button on the front panel or on the remote controller button to exit the Setup menu.

Using the remote controller

1. Press the Test button.

You will hear a pink noise which will be emitted from the front left speaker.

(1)Remember the volume level of this noise and then press the CH Sel button. The DTR-5.4 will now emit the pink noise from the center speaker.

(2)Using the Level Manual background /Manual background buttons, adjust the volume level of the noise from the center speaker so that it is at the same level as that was emitted from the front left speaker.

(3)Press the CH Sel button again. The DTR-5.4 will now emit the pink noise from the front right speaker.

Use the Level Manual background /Manual background buttons to adjust the volume of the noise from the front right speaker so that it is the same level as that was emitted from the center speaker.

(4)Use the CH Sel button to select other speakers and adjust the

volumes until all speakers are adjusted to the same level.

The pink noise level can be adjusted to anywhere between –12 and +12 decibels for all speakers in 1-decibel increments. For subwoofer, values between –15 and +12 dB can be set.

2. Press the Test button to complete

* Menu *****************

1.Hardware Config 2.Speaker Config 3.Speaker Distance

4.Level Calibration

5.Input Setup 6.Preference

Manual backgroundManual backgroundENTERQuit:SETUP

* Menu *****************

1.Speaker Config

 

4.Level Calibration

2.Speaker Distance

***********************

3.Level Calibration

4.Input Setup

: OdB

a.Left

5.OSD Setup

: OdB

b.Center

6.Preference

: OdB

c.Right

d.Surr Right

: OdB

e.Surr Back

: OdB

f.Surr Left

: OdB

g.Subwoofer

: OdB

Quit:SETUP

the procedure.

Note:

Speakers that you selected “No” or “None” for in the “Speaker Config” menu will be disabled.

2. Use the Manual background and Manual background cursor buttons to select “Left.”

You will hear a pink noise from the front left speaker.

(1)Remember the volume level of this noise and then press the Manual background cursor button. The DTR-5.4 will now emit the pink noise from the center speaker.

(2)Using the Manual background and Manual background cursor buttons, adjust the volume level of the noise from the center speaker so that it is at the same level as that was emitted from the front left speaker.

(3)Press the Manual background cursor button again. The DTR-5.4 will now emit the pink noise from the front right speaker.

Use the Manual background and Manual background cursor buttons to adjust the volume of the noise from the front right speaker so that it is the same level as that was emitted from the center speaker.

(4)Use the Manual background cursor button to select other speakers and adjust the volumes until all speakers are adjusted to the same level.

The pink noise level can be adjusted to anywhere between –12 and +12 decibels for all speakers in 1-decibel increments. For subwoofer, values between –15 and +12 dB can be set.

Press the Return button to return to the main menu.

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Basic Settings ContentsBefore using Setting up your DTR-6.4/5.430AVIS Important Safety InstructionsFor U.S. models Note to CATV system installer PrecautionsSupplied accessories 4. PowerConnecting the remote zone Zone 2 speakers ContentsBefore using Connecting your AV componentsProgramming the commands of remote ContentsConfiguring your DTR-6.4/5.4Advanced Settings Remote controllerAmplifier Features FeaturesDTR-6.4 DTR-5.4Using the remote controller Before using this unitConnecting the power cord Installing the remote controller batteriesDTR-6.4Front panel DTR-5.4Front panel Index parts and facilitiesIndex parts and facilities MEMORY indicator Front panel displayTUNED indicator AUTO indicatorIndex parts and facilities Rear panelIR IN/OUT Remote controllerIndex parts and facilities MONITOR OUT VIDEO/S VIDEOIndex parts and facilities Send/Learn indicatorCenter speaker About HomeTheaterEnjoying Home Theater For DTR-6.4onlyTerminal shapes AV cables and connectorsImproper connection Inserted completely Cable formsSurround back speaker placement Connecting speakersConnecting a subwoofer Connecting speakersConnecting the speaker cables Using the speaker cable labels2. Connecting a turntable PHONO DTR-6.4only Connecting your AV componentsConnecting your audio components 1. Connecting a compact disc player CDCOMPONENT VIDEO INPUT/OUTPUT Connecting your AV componentsConnecting your video components The flow of the video signals5. Connecting a DVD player DVD Connecting your AV components6. Connecting a video cassette recorder VIDEO Connecting your AV components9. Connecting video camera, etc. Video 4 Input Connecting your AV componentsConnecting your AV components Connecting the power cords from other devicesAssembling the AM loop antenna Connecting antennasConnecting the AM antenna cable Connecting the included antennasDirectional linkage Connecting antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaWhen using the ZONE 2 PRE OUT terminals Connecting the remote zone Zone 2 speakersWhen using the ZONE 2 SPEAKERS terminals When using the ZONE 2 LINE OUT terminalsFrom connecting block Mini plug cable A-BUS Connections for remote controlMiscellaneous Connections RS232Turning on the power Connecting the powerTurning on the power from the remote controller 52,54 Setup Menu53,55 Buttons used for navigating through the menus Setup Menua. Surr/Zone Hardware Configb. Surr Back DTR-6.4only crosscover frequency Speaker ConfigurationAdjustable Crossover for Bass Management Front speaker diameterNotes Front speaker diametercrosscover frequency a. Digital InputChanging the display Return Setup TapeReturn Setup ENTERBasic operation Enjoying music or videos with the DTR-6.4/5.4Light button on the remote controller DTR-6.4only Enjoying music or videos with the DTR-6.4/5.4 Using the sleep time remote controller onlyListening with headphones Adjusting the brightness of the front displayNotes Switching the displayTemporarily changing the speaker output levels Enjoying music or videos with the DTR-6.4/5.4Notes on DTS Selecting the type of audio input signalEnjoying music or videos with the DTR-6.4/5.4 NotesEnjoying DVD multichannel audio playback Using the tone controlBasic operation Changing the listening mode DTR-6.4only Enjoying DVD multichannel audio playbackListening to Radio Broadcasts Tuning into a radio stationListening to a stereo radio station FM mode Listening to Radio Broadcasts Presetting a radio stationSelecting a preset radio station Erasing a preset radio stationMono Listening ModesListening Modes T-D Theater-DimensionalEnhance Listening Modes• THX Surround EX Mono MovieRe-EQfunction for movies DTR-6.4only Selecting a listening mode DTR-6.4Listening Modes Listening Modes Selecting a listening mode DTR-5.4•While playing back DTS sources THX Cinema Fixing playback to specific surround modeListening Modes •While playing back DTS sourcesUsing the remote controller Using the buttonsAdjusting the volume for the remote zone Enjoying music in the remote zoneNotes RecordingRecording the input source Rec Out selector NotesRecording both the audio and video RecordingHint Notes Configuring the speakers DTR-6.4Calibrating the speaker levels Configuring the speakers DTR-6.4Notes Return Configuring the speakers DTR-5.4Setup Return SetupCalibrating the speaker levels Configuring the speakers DTR-5.4Using the remote controller the procedureInput Setup e. PCM fs 96kHz source Input SetupConfiguring the listening modes frequently you use d. Analog/PCM/D. F. 2ch sourceChanging the volume level display setting Adjusting the headphones volume levelSetting the background color for OSD Switching the OSD display modeBass Audio AdjustTreble Late Night Audio AdjustPro Logic II Music Dimension Dimension Double BassReverb Time Settings available when you play monaural signalAudio Adjust Reverb LevelControlling an Onkyo cassette tape deck Using remote controllerCalling up a preset radio station OverviewControlling an Integra/Onkyo DVD player Using remote controllerDisc Controlling an Integra/Onkyo CD playerUsing remote controller 1. Press the CD Mode button1 to 9, 0, --/---: Numeric keys Controlling an Onkyo MD recorderUsing remote controller Rec : RecordLearning a pre-programmingcode Entering a pre-programmingcodePre-programmingcodes Entering a pre-programmingcodeCable Mode Cable Mode Operating your programmed remote controllerDVD Mode DVD Player Mode SAT Mode Satellite Tuner Mode0,1 to 9, +10: Numeric keys Operating your programmed remote controllerVCR Mode VCR Mode TV Mode TV ModeProgramming procedure Notes Erasing the programmed command from one buttonNotes Executing the macro Using the macro functionWhat is the macro function? Programming the macroNotes Using the macro functionErasing a macro from the Macro 1 or 2 button NotesTUNER SECTION Specifications DTR-6.4REMOTE CONTROLLER AMPLIFIER SECTIONTUNER SECTION Specifications DTR-5.4REMOTE CONTROLLER AMPLIFIER SECTIONFM/AM TUNER Troubleshooting guidePOWER SPEAKERSOTHER Troubleshooting guideREMOTE CONTROLLER VIDEO and AUDIO“Not available with this signal” If one of the messages shown below appearsTroubleshooting guide “Not available with headphones use”Memo Printed in Japan Integra Division of ONKYO U.S.A. CORPORATIONIntegra Division of ONKYO CORPORATION Tel: 072-831-8111Fax:
Top Page Image Contents