Integra DTR-6.4/5.4 If one of the messages shown below appears, Troubleshooting guide

Page 78
If one of the messages shown below appears

Troubleshooting guide

If one of the messages shown below appears

“Not available with headphones use”

Operation not allowed because headphones are plugged into the DTR-6.4/5.4.

“Not available with Multichannel use”

Operation not allowed while the multi-channel output is being used.

“Not available in this Sp Config”

Will not work with the current speaker configuration settings.

“Not available in Zone 2 mode”

Setting not allowed because the Zone 2 mode is turned on.

“Only available with Dolby D”

No setting other than Dolby Digital can be set.

“Not available in this Listening mode”

Will not work with the current listening mode.

“Not available with this signal”

The listening mode cannot be selected with the current input source.

“Not available with Muting”

Operation not allowed because the muting is activated.

“Zone 2 is not On”

Will not work because the Zone 2 has not been turned on.

Also refer to the respective instruction manuals of the CD player, DVD player, video cassette recorder, TV monitor, etc., that compose your entertainment system.

The DTR-6.4/5.4 contains an internal microcomputer that performs high-level operations. However, on extremely rare occasions, noise or interference from an external source or static electricity may cause faulty operation. If this occurs, unplug the power cord from the wall outlet, wait five or more seconds, and then plug it back in. This should correct the situation.

*To reset the surround mode and other settings to the factory default settings, hold down the Video 1 button with the DTR- 6.4/5.4 turned on and then press the Standby/On button. “CLEAR” appears in the front display and the DTR-6.4/5.4 enters the standby state.

78

Image 78
Contents Setting up your DTR-6.4/5.430 ContentsBefore using Basic SettingsImportant Safety Instructions AVIS4. Power PrecautionsSupplied accessories For U.S. models Note to CATV system installerConnecting your AV components ContentsBefore using Connecting the remote zone Zone 2 speakersRemote controller ContentsConfiguring your DTR-6.4/5.4Advanced Settings Programming the commands of remoteDTR-5.4 FeaturesDTR-6.4 Amplifier FeaturesInstalling the remote controller batteries Before using this unitConnecting the power cord Using the remote controllerIndex parts and facilities DTR-6.4Front panel DTR-5.4Front panelIndex parts and facilities AUTO indicator Front panel displayTUNED indicator MEMORY indicatorRear panel Index parts and facilitiesMONITOR OUT VIDEO/S VIDEO Remote controllerIndex parts and facilities IR IN/OUTSend/Learn indicator Index parts and facilitiesFor DTR-6.4only About HomeTheaterEnjoying Home Theater Center speakerCable forms AV cables and connectorsImproper connection Inserted completely Terminal shapesConnecting speakers Surround back speaker placementUsing the speaker cable labels Connecting speakersConnecting the speaker cables Connecting a subwoofer1. Connecting a compact disc player CD Connecting your AV componentsConnecting your audio components 2. Connecting a turntable PHONO DTR-6.4onlyThe flow of the video signals Connecting your AV componentsConnecting your video components COMPONENT VIDEO INPUT/OUTPUTConnecting your AV components 5. Connecting a DVD player DVDConnecting your AV components 6. Connecting a video cassette recorder VIDEOConnecting your AV components 9. Connecting video camera, etc. Video 4 InputConnecting the power cords from other devices Connecting your AV componentsConnecting the included antennas Connecting antennasConnecting the AM antenna cable Assembling the AM loop antennaConnecting an AM outdoor antenna Connecting antennasConnecting an FM outdoor antenna Directional linkageWhen using the ZONE 2 LINE OUT terminals Connecting the remote zone Zone 2 speakersWhen using the ZONE 2 SPEAKERS terminals When using the ZONE 2 PRE OUT terminalsFrom connecting block Mini plug cable RS232 Connections for remote controlMiscellaneous Connections A-BUSConnecting the power Turning on the powerTurning on the power from the remote controller Setup Menu 52,5453,55 Setup Menu Buttons used for navigating through the menusHardware Config a. Surr/Zoneb. Surr Back DTR-6.4only Front speaker diameter Speaker ConfigurationAdjustable Crossover for Bass Management crosscover frequencya. Digital Input Front speaker diametercrosscover frequency NotesENTER Return Setup TapeReturn Setup Changing the displayEnjoying music or videos with the DTR-6.4/5.4 Basic operationLight button on the remote controller DTR-6.4only Adjusting the brightness of the front display Using the sleep time remote controller onlyListening with headphones Enjoying music or videos with the DTR-6.4/5.4Enjoying music or videos with the DTR-6.4/5.4 Switching the displayTemporarily changing the speaker output levels NotesNotes Selecting the type of audio input signalEnjoying music or videos with the DTR-6.4/5.4 Notes on DTSUsing the tone control Enjoying DVD multichannel audio playbackBasic operation Enjoying DVD multichannel audio playback Changing the listening mode DTR-6.4onlyTuning into a radio station Listening to Radio BroadcastsListening to a stereo radio station FM mode Erasing a preset radio station Presetting a radio stationSelecting a preset radio station Listening to Radio BroadcastsT-D Theater-Dimensional Listening ModesListening Modes MonoMono Movie Listening Modes• THX Surround EX EnhanceSelecting a listening mode DTR-6.4 Re-EQfunction for movies DTR-6.4onlyListening Modes Selecting a listening mode DTR-5.4 Listening Modes•While playing back DTS sources Fixing playback to specific surround modeListening Modes •While playing back DTS sources THX CinemaEnjoying music in the remote zone Using the buttonsAdjusting the volume for the remote zone Using the remote controllerNotes RecordingRecording the input source Rec Out selector NotesRecording Recording both the audio and videoHint Configuring the speakers DTR-6.4 NotesConfiguring the speakers DTR-6.4 Calibrating the speaker levelsNotes Setup Configuring the speakers DTR-5.4Setup Return Returnthe procedure Configuring the speakers DTR-5.4Using the remote controller Calibrating the speaker levelsInput Setup d. Analog/PCM/D. F. 2ch source Input SetupConfiguring the listening modes frequently you use e. PCM fs 96kHz sourceSwitching the OSD display mode Adjusting the headphones volume levelSetting the background color for OSD Changing the volume level display settingAudio Adjust BassTreble Double Bass Audio AdjustPro Logic II Music Dimension Dimension Late NightReverb Level Settings available when you play monaural signalAudio Adjust Reverb TimeOverview Using remote controllerCalling up a preset radio station Controlling an Onkyo cassette tape deckUsing remote controller Controlling an Integra/Onkyo DVD player1. Press the CD Mode button Controlling an Integra/Onkyo CD playerUsing remote controller DiscRec : Record Controlling an Onkyo MD recorderUsing remote controller 1 to 9, 0, --/---: Numeric keysEntering a pre-programmingcode Learning a pre-programmingcodeEntering a pre-programmingcode Pre-programmingcodesSAT Mode Satellite Tuner Mode Operating your programmed remote controllerDVD Mode DVD Player Mode Cable Mode Cable ModeTV Mode TV Mode Operating your programmed remote controllerVCR Mode VCR Mode 0,1 to 9, +10: Numeric keysProgramming procedure Erasing the programmed command from one button NotesNotes Programming the macro Using the macro functionWhat is the macro function? Executing the macroNotes Using the macro functionErasing a macro from the Macro 1 or 2 button NotesAMPLIFIER SECTION Specifications DTR-6.4REMOTE CONTROLLER TUNER SECTIONAMPLIFIER SECTION Specifications DTR-5.4REMOTE CONTROLLER TUNER SECTIONSPEAKERS Troubleshooting guidePOWER FM/AM TUNERVIDEO and AUDIO Troubleshooting guideREMOTE CONTROLLER OTHER“Not available with headphones use” If one of the messages shown below appearsTroubleshooting guide “Not available with this signal”Memo Tel: 072-831-8111Fax: Integra Division of ONKYO U.S.A. CORPORATIONIntegra Division of ONKYO CORPORATION Printed in Japan