Windsor SGJ32, 10052530 Vacuum Filter, Float Switch, Solution Strainer, Brake Adjustment

Page 32

MAINTENANCE

5.VACUUM FILTER

The vacuum filter is located inside the recovery tank. The vacuum filter prevents debris from entering the vacuum motor. Daily remove and clean filter of any debris for maximum airflow.

6.FLOAT SWITCH

The float switch is located inside the recovery tank. The purpose of the float switch is to notify the user that the recovery tank is full. When the float switch is activated, the scrub brush motors and solution flow will stop, the scrub deck will raise, the squeegee will rise after 60 seconds, and the vacuum motor will turn off 10 seconds later.

Icon appears on information screen 1 when

float switch is activated.

7.SOLUTION STRAINER

The solution strainer is located behind the right rear wheel of the Glide. The solution strainer protects the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris. Drain the solution tank and clean the solution strainer. To remove the strainer, turn the bottom part of the strainer counterclockwise until the bottom is separated. Clean out the debris from the wire mesh and re-assemble. Make sure the O-ring gasket is in place when re-assembled.

8.BRAKE

(Refer to Brake Group in the Parts section of the manual).

The brake pedal and parking brake operate the self- centering front wheel disc brake. The disc and caliper should be inspected every 200hours of operation for cracks and disc wear. The brake should be adjusted so that the disc pads are as close to the disc as possible, without causing brakes to drag.

BRAKE ADJUSTMENT

FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and remove key.

1.Disconnect batteries from machine.

2.Turn the steering wheel fully to the left.

3.Locate the brake adjustment screw on the brake caliper.

4.Loosen the lock nut.

5.Turn adjustment screw in until finger tight, then back off 1/8 turn.

6.Hold adjustment screw and tighten lock nut.

9.STEERING CHAIN TENSIONER

(Refer to Steering Group in parts section of manual).

The steering chain transfers power from the steering shaft to the drive wheel, controlling steering response. Check the chain condition and tension every 200 hours of operation. Proper chain tension is important to maintain steering response. The chain should deflect 1/16 in. Use a light spray lube if needed.

STEERING CHAIN TENSIONER ADJUSTMENT

1.Locate chain tensioner bolts.

2.To increase tension, tighten lock nuts retaining chain tension plate.

3.To decrease tension, loosen lock nuts retaining chain tension plate.

4-9

SGJ32 86037680 01/03/07

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Scrubber Overview Machine Data LOG/OVERVIEWYour Dealer Table of Contents HOW to USE this Manual Parts ListImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls KEY Switch Emergency Stop ButtonONE Touch Switch Brush Pressure SwitchSolution Control Switch VACUUM/SQUEEGEE SwitchDisplay Toggle Switch Information Display -SCREENControls Headlight Switch Optional Recycle Switch OptionalRecycle Indicator Light Optional Directional Control Pedal and Speed Reduction Feature Speed Reduction FeatureBrake Pedal Parking Brake LeverSeat Adjustment Grab BAR Squeegee Camber Adjustment KnobSqueegee Defection Adjustment Knob Side Squeegee Defection Adjustment KnobMachine Operation PRE-RUN Machine InspectionStarting Machine Filling the MachineEmergency Stop Procedure To Begin ScrubbingTo Stop Scrubbing Double ScrubEmptying and Cleaning Tanks Recovery Tank Solution TankMaintenance Battery Maintenance BatteriesLOW Battery SHUT-DOWN To Charge BatteriesTo Remove Batteries To Replace BatteriesSqueegee Adjustment To Adjust Squeegee PitchTo Replace or Rotate Front Squeegee Blades To Remove Squeegee AssemblyTo Replace or Rotate Rear Squeegee Blades To Replace or Rotate Side Squeegee Blades Side Squeegee AdjustmentAdjusting the Side Squeegee Deflection Replacing or Installing Scrub Brushes Scrub BrushesUncoated Floors Finished FloorsFloat Switch Solution StrainerBrake Adjustment Steering Chain Tensioner AdjustmentVacuum Motor Changing Vacuum MotorChanging Brush Motors Brush Motor Carbon Brush ReplacementBrush Motor Traction Motor Traction Motor Carbon Brush ReplacmentFuse Circuit BreakersSqueegee Actuator REMOVAL/REPLACEMENT Squeegee Actuator AdjustmentScrub Deck Actuator REMOVAL/REPLACEMENT Scrub Deck Actuator AdjustmentTransporting Machine Towing or Pushing MachineMachine TIE-DOWNS Preparation for TransportingJacking Machine Machine JackingTo Jack UP Machine Machine StorageMaintenance Service Schedule Maintenance Before Each Work PeriodAfter Each Work Period HRSSolution Machine TroubleshootingProblem Cause Error Code Problem Cause Solution

10052530, SGJ32 specifications

The Windsor SGJ32, model 10052530, is a highly sophisticated and versatile industrial sewing machine engineered for optimal performance in various textile applications. Designed for heavy-duty usage, this model stands out due to its robust construction and innovative technologies that cater to the needs of modern manufacturing environments.

One of the defining features of the SGJ32 is its advanced stitching capabilities. The machine is equipped with a high-speed motor that enables it to achieve impressive stitching rates, allowing users to maximize productivity. It can seamlessly handle a wide range of fabrics, from lightweight materials to heavy-duty textiles, making it an ideal choice for diverse sewing applications, including upholstery, outdoor gear, and garment production.

In terms of technology, the SGJ32 integrates computer numerical control (CNC) systems that enhance precision and repeatability in stitching. This technology allows for intricate designs and patterns to be produced with high accuracy, reducing the margin for error and ensuring consistent quality across batches. Additionally, the machine features a user-friendly interface with touch controls, making it easier for operators to adjust settings quickly and efficiently.

Another notable characteristic of the Windsor SGJ32 is its adaptability. The machine can be easily customized with various attachments and accessories, empowering users to tackle specific tasks and improve workflow. Its adjustable stitch length and width provide further versatility, enabling operators to switch between different sewing techniques without hassle.

The construction of the SGJ32 is another key aspect that contributes to its reliability. Built from high-quality materials, the machine is designed to withstand the rigors of continuous operation while minimizing wear and tear. This durability not only extends the lifespan of the equipment but also ensures lower maintenance costs over time.

Moreover, the SGJ32 incorporates safety features such as automatic needle positioning and a thread trimmer, which enhance operational safety and ease of use. These features reduce the risk of accidents and streamline the sewing process, allowing operators to focus on their craft without unnecessary distractions.

In conclusion, the Windsor SGJ32, model 10052530, is a powerful, versatile, and technologically advanced sewing machine that caters to a wide range of industrial applications. With its high-speed capabilities, precision control, adaptability, and robust construction, it is an essential tool for manufacturers seeking to improve efficiency and maintain quality in their production processes.
Top Page Image Contents