Windsor 10052530, SGJ32 Scrub Deck Actuator REMOVAL/REPLACEMENT, Scrub Deck Actuator Adjustment

Page 37

16.SCRUB DECK ACTUATOR REMOVAL/REPLACEMENT

FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake.

1.Lower scrub deck, if possible, by pressing one- touch switch and turn key to off position.

2.Remove lower clevis pin by removing rue ring from clevis pin, then pull pin out from scrub deck lift bracket and actuator.

3.Remove upper clevis pin (ball detent type) by pulling on it’s ring (located on left side), then pull it out from the frame and actuator. Remove from the machine, make sure not to allow actuator barrel position to move.

4.Disconnect actuator from wire harness.

5.Reverse steps to install.

MAINTENANCE

SCRUB DECK ACTUATOR ADJUSTMENT

The actuator will need to be adjusted when replaced. The actuator needs to be set such that the scrub deck stops barely touch the rubber bumpers on the frame in the raised/retracted position.

To adjust the actuator:

1.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully extended. Positive power to white wire, and negative/ground to black. Limit switch within actuator will stop it.

2.Turn barrel out one or more full turns to assure that when it is retracted it will not bind against itself.

3.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully retracted. Positive power to black wire, and negative/ground to white wire. Limit switch within actuator will stop it.

4.With actuator fully retracted, turn barrel in until it touches the base of the threaded shaft.

5.At the bottomed out position, turn the barrel out 3 full turns, then enough to allow connection to lift linkage.

6.Connect actuator to lift linkage and check that in the raised/retracted position the stops on the

scrub deck barely touch the rubber bumpers on the frame.

NOTE: If further adjustment is needed, disconnect the actuator from scrub deck lift linkage and turn the barrel one half-turn at a time in to make scrub deck stops closer to bumpers, or out to eliminate excessive pressure against bumpers.

SGJ32 86037680 01/03/07

4-14

 

Image 37
Contents Scrubber Your Dealer Machine Data LOG/OVERVIEWOverview Table of Contents Parts List HOW to USE this ManualRead ALL Instructions Before Using this Machine Important Safety InstructionsHazard Intensity Level Hazard Intensity LevelSafety Label Location DIMENSION/CAPACITY Technical SpecificationsMeasure Special NotesHOW the Machine Works Components Controls Emergency Stop Button KEY SwitchBrush Pressure Switch ONE Touch SwitchVACUUM/SQUEEGEE Switch Solution Control SwitchInformation Display -SCREEN Display Toggle SwitchControls Recycle Indicator Light Optional Recycle Switch OptionalHeadlight Switch Optional Speed Reduction Feature Directional Control Pedal and Speed Reduction FeatureBrake Pedal Parking Brake LeverSqueegee Camber Adjustment Knob Seat Adjustment Grab BARSqueegee Defection Adjustment Knob Side Squeegee Defection Adjustment KnobPRE-RUN Machine Inspection Machine OperationStarting Machine Filling the MachineTo Begin Scrubbing Emergency Stop ProcedureTo Stop Scrubbing Double ScrubSolution Tank Emptying and Cleaning Tanks Recovery TankMaintenance Batteries Battery MaintenanceTo Charge Batteries LOW Battery SHUT-DOWNTo Replace Batteries To Remove BatteriesTo Adjust Squeegee Pitch Squeegee AdjustmentTo Replace or Rotate Rear Squeegee Blades To Remove Squeegee AssemblyTo Replace or Rotate Front Squeegee Blades Adjusting the Side Squeegee Deflection Side Squeegee AdjustmentTo Replace or Rotate Side Squeegee Blades Scrub Brushes Replacing or Installing Scrub BrushesUncoated Floors Finished FloorsSolution Strainer Float SwitchBrake Adjustment Steering Chain Tensioner AdjustmentChanging Vacuum Motor Vacuum MotorBrush Motor Brush Motor Carbon Brush ReplacementChanging Brush Motors Traction Motor Carbon Brush Replacment Traction MotorFuse Circuit BreakersSqueegee Actuator Adjustment Squeegee Actuator REMOVAL/REPLACEMENTScrub Deck Actuator Adjustment Scrub Deck Actuator REMOVAL/REPLACEMENTTowing or Pushing Machine Transporting MachineMachine TIE-DOWNS Preparation for TransportingMachine Jacking Jacking MachineTo Jack UP Machine Machine StorageMaintenance Before Each Work Period Maintenance Service ScheduleAfter Each Work Period HRSProblem Cause Error Code Machine TroubleshootingSolution Problem Cause Solution

10052530, SGJ32 specifications

The Windsor SGJ32, model 10052530, is a highly sophisticated and versatile industrial sewing machine engineered for optimal performance in various textile applications. Designed for heavy-duty usage, this model stands out due to its robust construction and innovative technologies that cater to the needs of modern manufacturing environments.

One of the defining features of the SGJ32 is its advanced stitching capabilities. The machine is equipped with a high-speed motor that enables it to achieve impressive stitching rates, allowing users to maximize productivity. It can seamlessly handle a wide range of fabrics, from lightweight materials to heavy-duty textiles, making it an ideal choice for diverse sewing applications, including upholstery, outdoor gear, and garment production.

In terms of technology, the SGJ32 integrates computer numerical control (CNC) systems that enhance precision and repeatability in stitching. This technology allows for intricate designs and patterns to be produced with high accuracy, reducing the margin for error and ensuring consistent quality across batches. Additionally, the machine features a user-friendly interface with touch controls, making it easier for operators to adjust settings quickly and efficiently.

Another notable characteristic of the Windsor SGJ32 is its adaptability. The machine can be easily customized with various attachments and accessories, empowering users to tackle specific tasks and improve workflow. Its adjustable stitch length and width provide further versatility, enabling operators to switch between different sewing techniques without hassle.

The construction of the SGJ32 is another key aspect that contributes to its reliability. Built from high-quality materials, the machine is designed to withstand the rigors of continuous operation while minimizing wear and tear. This durability not only extends the lifespan of the equipment but also ensures lower maintenance costs over time.

Moreover, the SGJ32 incorporates safety features such as automatic needle positioning and a thread trimmer, which enhance operational safety and ease of use. These features reduce the risk of accidents and streamline the sewing process, allowing operators to focus on their craft without unnecessary distractions.

In conclusion, the Windsor SGJ32, model 10052530, is a powerful, versatile, and technologically advanced sewing machine that caters to a wide range of industrial applications. With its high-speed capabilities, precision control, adaptability, and robust construction, it is an essential tool for manufacturers seeking to improve efficiency and maintain quality in their production processes.