Windsor SGJ32, 10052530 Squeegee Actuator REMOVAL/REPLACEMENT, Squeegee Actuator Adjustment

Page 36

MAINTENANCE

15.SQUEEGEE ACTUATOR REMOVAL/REPLACEMENT

FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake.

1.Remove squeegee to gain access to lift system.

2.Lower squeegee lift linkage, if possible, by pressing bottom of vacuum/squeegee switch and turn key to the off position.

3.Remove lower clevis pin by removing rue ring and washer from clevis pin, then pull pin out from squeegee lift bracket and actuator.

4.Remove upper clevis pin (ball detent type) by pulling on it’s ring (located on left side), then pull it out from the frame and actuator. Pull actuator down to remove from the machine, make sure not to allow actuator barrel position to move.

5.Disconnect actuator from wire harness.

6.Reverse steps to install.

SQUEEGEE ACTUATOR ADJUSTMENT

The actuator will need to be adjusted when replaced. The actuator needs to be set such that it does not bind against itself in the raised/retracted position, and does not bind against the axle in the lowered/extended position.

To adjust the actuator:

1.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully extended. Positive power to white wire, and negative/ground to black. Limit switch within actuator will stop it.

2.Turn barrel out one or more full turns to assure that when it is retracted it will not bind against itself.

3.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully retracted. Positive power to black wire, and negative/ground to white wire. Limit switch within actuator will stop it.

4.With actuator fully retracted, turn barrel in until it touches the base of the threaded shaft.

5.At the bottomed out position, turn the barrel out 1 full turn, then enough to allow connection to lift linkage.

6.Connect actuator to lift linkage and check that in the raised/retracted position it does not bind against itself, and in the lowered/extended position does not bind against the axle

7.If further adjustment is needed, disconnect the actuator from squeegee lift linkage and turn the barrel one half-turn at a time in to eliminate binding against axle, or out to eliminate binding against itself.

4-13

SGJ32 86037680 01/03/07

 

Image 36
Contents Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents HOW to USE this Manual Parts ListImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls KEY Switch Emergency Stop ButtonONE Touch Switch Brush Pressure SwitchSolution Control Switch VACUUM/SQUEEGEE SwitchDisplay Toggle Switch Information Display -SCREENControls Recycle Switch Optional Recycle Indicator Light OptionalHeadlight Switch Optional Directional Control Pedal and Speed Reduction Feature Speed Reduction FeatureBrake Pedal Parking Brake LeverSeat Adjustment Grab BAR Squeegee Camber Adjustment KnobSqueegee Defection Adjustment Knob Side Squeegee Defection Adjustment KnobMachine Operation PRE-RUN Machine InspectionStarting Machine Filling the MachineEmergency Stop Procedure To Begin ScrubbingTo Stop Scrubbing Double ScrubEmptying and Cleaning Tanks Recovery Tank Solution TankMaintenance Battery Maintenance BatteriesLOW Battery SHUT-DOWN To Charge BatteriesTo Remove Batteries To Replace BatteriesSqueegee Adjustment To Adjust Squeegee PitchTo Remove Squeegee Assembly To Replace or Rotate Rear Squeegee BladesTo Replace or Rotate Front Squeegee Blades Side Squeegee Adjustment Adjusting the Side Squeegee DeflectionTo Replace or Rotate Side Squeegee Blades Replacing or Installing Scrub Brushes Scrub BrushesUncoated Floors Finished FloorsFloat Switch Solution StrainerBrake Adjustment Steering Chain Tensioner AdjustmentVacuum Motor Changing Vacuum MotorBrush Motor Carbon Brush Replacement Brush MotorChanging Brush Motors Traction Motor Traction Motor Carbon Brush ReplacmentFuse Circuit BreakersSqueegee Actuator REMOVAL/REPLACEMENT Squeegee Actuator AdjustmentScrub Deck Actuator REMOVAL/REPLACEMENT Scrub Deck Actuator AdjustmentTransporting Machine Towing or Pushing MachineMachine TIE-DOWNS Preparation for TransportingJacking Machine Machine JackingTo Jack UP Machine Machine StorageMaintenance Service Schedule Maintenance Before Each Work PeriodAfter Each Work Period HRSMachine Troubleshooting Problem Cause Error CodeSolution Problem Cause Solution

10052530, SGJ32 specifications

The Windsor SGJ32, model 10052530, is a highly sophisticated and versatile industrial sewing machine engineered for optimal performance in various textile applications. Designed for heavy-duty usage, this model stands out due to its robust construction and innovative technologies that cater to the needs of modern manufacturing environments.

One of the defining features of the SGJ32 is its advanced stitching capabilities. The machine is equipped with a high-speed motor that enables it to achieve impressive stitching rates, allowing users to maximize productivity. It can seamlessly handle a wide range of fabrics, from lightweight materials to heavy-duty textiles, making it an ideal choice for diverse sewing applications, including upholstery, outdoor gear, and garment production.

In terms of technology, the SGJ32 integrates computer numerical control (CNC) systems that enhance precision and repeatability in stitching. This technology allows for intricate designs and patterns to be produced with high accuracy, reducing the margin for error and ensuring consistent quality across batches. Additionally, the machine features a user-friendly interface with touch controls, making it easier for operators to adjust settings quickly and efficiently.

Another notable characteristic of the Windsor SGJ32 is its adaptability. The machine can be easily customized with various attachments and accessories, empowering users to tackle specific tasks and improve workflow. Its adjustable stitch length and width provide further versatility, enabling operators to switch between different sewing techniques without hassle.

The construction of the SGJ32 is another key aspect that contributes to its reliability. Built from high-quality materials, the machine is designed to withstand the rigors of continuous operation while minimizing wear and tear. This durability not only extends the lifespan of the equipment but also ensures lower maintenance costs over time.

Moreover, the SGJ32 incorporates safety features such as automatic needle positioning and a thread trimmer, which enhance operational safety and ease of use. These features reduce the risk of accidents and streamline the sewing process, allowing operators to focus on their craft without unnecessary distractions.

In conclusion, the Windsor SGJ32, model 10052530, is a powerful, versatile, and technologically advanced sewing machine that caters to a wide range of industrial applications. With its high-speed capabilities, precision control, adaptability, and robust construction, it is an essential tool for manufacturers seeking to improve efficiency and maintain quality in their production processes.