Windsor 10052530 Machine Operation, PRE-RUN Machine Inspection, Starting Machine, Scrubbing

Page 21

PRE-RUN MACHINE INSPECTION

1.Do a pre-run inspection to find possible problems that could cause poor performance or lost time from breakdown. Follow the same procedure each time to avoid missing steps. Visually check for exterior damage, leaks, damaged or worn tires.

2.Check brushes or pads and drivers for proper installation and wear. Weekly check scrub deck skirts for proper contact with floor. See BRUSHES in MAINTENANCE SECTION.

3.Check squeegee for wear and proper adjustment. See SQUEEGEE ADJUSTMENT in

MAINTENANCE SECTION.

4.Check for securely attached drain hose, plug, and caps.

5.Check battery condition, recharge if necessary. See BATTERIES in maintenance section.

6.Check the brakes and steering for proper operation. See BRAKES and STEERING in

MAINTENANCE SECTION.

STARTING MACHINE

NOTE: Perform pre-run machine check before operating machine.

FOR SAFETY: Before starting machine, make sure that all safety devices are in place and operating properly.

1.The operator should be in the seat with the right foot on the brake pedal or with the parking brake on. The directional pedal must be in the neutral position to avoid unintentional movement.

NOTE: The Operator must be in position on the seat to activate machine in desired direction.

2.Turn the key switch clockwise to the “ON” position.

3.Release the brake, then press lightly on the directional pedal in the desired direction and drive to the filling area.

FILLING THE MACHINE

FOR SAFETY: Before leaving or servicing machine; stop on level surface, set parking brake, turn off machine and remove key.

1.Set squeegee and scrub deck to up position, set parking brake, and turn off key switch.

2.Remove solution tank cover.

 

!

 

 

 

Flammable materials can

 

 

 

 

 

 

 

 

cause an explosion or fire.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Do not use flammable materials in the tanks.

MACHINE OPERATION

3.The solution tank can be filled to the FULL marking of the fill inlet. Leave room for detergent. The solution tank capacity is 30 gallons (114 liters).

The water must not be hotter than 140' (60'C) to prevent damage to the tank. Measure the required amount of chemical into the solution tank after filling with water. Dry chemicals should be thoroughly mixed before being added into solution tank. Commercially available, high alkaline floor cleaners are suitable for use in the solution system.

4.Inspect solution tank cover vent for obstructions. Replace solution tank cover.

SCRUBBING

Plan the scrubbing pattern in advance. The longest track is around the perimeter of the area to be cleaned. For efficient operation, the runs should be the longest possible without turning, stopping, or raising or lowering scrub deck/squeegee.

In order to achieve the best possible results, the area which is to be cleaned should be swept before scrubbing. Large debris, strings and wire must be removed to prevent being caught in brushes or squeegee.

The machine will automatically raise the squeegee slightly when reverse travel is selected. If the machine is allowed to stand in neutral with the scrub deck down for more than 2 seconds, the solutions flow stops and brush motors stop. If either forward or reverse travel is selected, the solution flow will continue in the same setting and the scrub brush motors will continue in their same setting once movement of machine begins. Overlap the brush path and avoid transporting over previously cleaned areas.

SGJ32 86037680 01/03/07

3-14

 

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents Parts List HOW to USE this ManualRead ALL Instructions Before Using this Machine Important Safety InstructionsHazard Intensity Level Hazard Intensity LevelSafety Label Location DIMENSION/CAPACITY Technical SpecificationsMeasure Special NotesHOW the Machine Works Components Controls Emergency Stop Button KEY SwitchBrush Pressure Switch ONE Touch SwitchVACUUM/SQUEEGEE Switch Solution Control SwitchInformation Display -SCREEN Display Toggle SwitchControls Recycle Switch Optional Recycle Indicator Light OptionalHeadlight Switch Optional Speed Reduction Feature Directional Control Pedal and Speed Reduction FeatureBrake Pedal Parking Brake LeverSqueegee Camber Adjustment Knob Seat Adjustment Grab BARSqueegee Defection Adjustment Knob Side Squeegee Defection Adjustment KnobPRE-RUN Machine Inspection Machine OperationStarting Machine Filling the MachineTo Begin Scrubbing Emergency Stop ProcedureTo Stop Scrubbing Double ScrubSolution Tank Emptying and Cleaning Tanks Recovery TankMaintenance Batteries Battery MaintenanceTo Charge Batteries LOW Battery SHUT-DOWNTo Replace Batteries To Remove BatteriesTo Adjust Squeegee Pitch Squeegee AdjustmentTo Remove Squeegee Assembly To Replace or Rotate Rear Squeegee BladesTo Replace or Rotate Front Squeegee Blades Side Squeegee Adjustment Adjusting the Side Squeegee DeflectionTo Replace or Rotate Side Squeegee Blades Scrub Brushes Replacing or Installing Scrub BrushesUncoated Floors Finished FloorsSolution Strainer Float SwitchBrake Adjustment Steering Chain Tensioner AdjustmentChanging Vacuum Motor Vacuum MotorBrush Motor Carbon Brush Replacement Brush MotorChanging Brush Motors Traction Motor Carbon Brush Replacment Traction MotorFuse Circuit BreakersSqueegee Actuator Adjustment Squeegee Actuator REMOVAL/REPLACEMENTScrub Deck Actuator Adjustment Scrub Deck Actuator REMOVAL/REPLACEMENTTowing or Pushing Machine Transporting MachineMachine TIE-DOWNS Preparation for TransportingMachine Jacking Jacking MachineTo Jack UP Machine Machine StorageMaintenance Before Each Work Period Maintenance Service ScheduleAfter Each Work Period HRSMachine Troubleshooting Problem Cause Error CodeSolution Problem Cause Solution

10052530, SGJ32 specifications

The Windsor SGJ32, model 10052530, is a highly sophisticated and versatile industrial sewing machine engineered for optimal performance in various textile applications. Designed for heavy-duty usage, this model stands out due to its robust construction and innovative technologies that cater to the needs of modern manufacturing environments.

One of the defining features of the SGJ32 is its advanced stitching capabilities. The machine is equipped with a high-speed motor that enables it to achieve impressive stitching rates, allowing users to maximize productivity. It can seamlessly handle a wide range of fabrics, from lightweight materials to heavy-duty textiles, making it an ideal choice for diverse sewing applications, including upholstery, outdoor gear, and garment production.

In terms of technology, the SGJ32 integrates computer numerical control (CNC) systems that enhance precision and repeatability in stitching. This technology allows for intricate designs and patterns to be produced with high accuracy, reducing the margin for error and ensuring consistent quality across batches. Additionally, the machine features a user-friendly interface with touch controls, making it easier for operators to adjust settings quickly and efficiently.

Another notable characteristic of the Windsor SGJ32 is its adaptability. The machine can be easily customized with various attachments and accessories, empowering users to tackle specific tasks and improve workflow. Its adjustable stitch length and width provide further versatility, enabling operators to switch between different sewing techniques without hassle.

The construction of the SGJ32 is another key aspect that contributes to its reliability. Built from high-quality materials, the machine is designed to withstand the rigors of continuous operation while minimizing wear and tear. This durability not only extends the lifespan of the equipment but also ensures lower maintenance costs over time.

Moreover, the SGJ32 incorporates safety features such as automatic needle positioning and a thread trimmer, which enhance operational safety and ease of use. These features reduce the risk of accidents and streamline the sewing process, allowing operators to focus on their craft without unnecessary distractions.

In conclusion, the Windsor SGJ32, model 10052530, is a powerful, versatile, and technologically advanced sewing machine that caters to a wide range of industrial applications. With its high-speed capabilities, precision control, adaptability, and robust construction, it is an essential tool for manufacturers seeking to improve efficiency and maintain quality in their production processes.
Top Page Image Contents