Windsor SGJ32, 10052530 operating instructions Squeegee Adjustment, To Adjust Squeegee Pitch

Page 28

MAINTENANCE

2. SQUEEGEE ADJUSTMENT

Adjusting the squeegee is a two-part process. First, the squeegee tool must have correct pitch in order for the squeegee blade to have the same deflection at each tip as well as the center. The pitch adjustment is facilitated by the use of a spirit level mounted on the squeegee tool. The second adjustment is the amount of deflection or down pressure on the squeegee.

TO ADJUST SQUEEGEE PITCH

1.Choose a smooth, level surface. Turn on the key switch, release the machine parking brake, lower the squeegee and drive forward at least 2 feet (60 cm).

2.With the squeegee down, stop the machine and set the parking brake. Do not allow the machine to roll back.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

3.Determine the differences, if any, in deflection of the squeegee blade between each end and the middle. Proper adjustment is obtained when deflection is equal all the way across tool. This should correspond to the bubble being in the middle position of the spirit level.

4.To decrease the deflection of the squeegee blade at the ends, turn knob on squeegee trailing arm clockwise. To increase the deflection at the ends of the squeegee assembly, turn knob counter clockwise.

5.Again check the deflection of the squeegee blades. Repeat steps 1 through 4 until the deflection is equal across the entire rear squeegee blade.

TO ADJUST SQUEEGEE DEFLECTION

3/8”

PROPER DEFLECTION OF SQUEEGEE BLADE

1.Choose a smooth, level surface. Lower the squeegee and drive forward at least 2 feet.

2.With the squeegee down, stop the machine and set the parking brake. Do not allow the machine to roll back.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

3.Observe the amount of squeegee deflection. It should deflect 3/8in (9.5 mm) across the entire width of the squeegee.

4.To adjust the squeegee deflection, loosen knob on the squeegee slide bar.

5.Sliding bar to left increases deflection. Sliding bar to right decreases deflection.

6.Tighten knob on squeegee slide bar.

7.Turn on the key switch, release the machine parking brake. Raise, then lower squeegee assembly by pressing the vacuum switch. Drive forward at least 2 feet.

8.Repeat steps 2 through 7 until defection of 3/8 in. (9.5 mm) is reached.

4-5

SGJ32 86037680 01/03/07

Image 28
Contents Scrubber Your Dealer Machine Data LOG/OVERVIEWOverview Table of Contents HOW to USE this Manual Parts ListImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls KEY Switch Emergency Stop ButtonONE Touch Switch Brush Pressure SwitchSolution Control Switch VACUUM/SQUEEGEE SwitchDisplay Toggle Switch Information Display -SCREENControls Recycle Indicator Light Optional Recycle Switch OptionalHeadlight Switch Optional Directional Control Pedal and Speed Reduction Feature Speed Reduction FeatureBrake Pedal Parking Brake LeverSeat Adjustment Grab BAR Squeegee Camber Adjustment KnobSqueegee Defection Adjustment Knob Side Squeegee Defection Adjustment KnobMachine Operation PRE-RUN Machine InspectionStarting Machine Filling the MachineEmergency Stop Procedure To Begin ScrubbingTo Stop Scrubbing Double ScrubEmptying and Cleaning Tanks Recovery Tank Solution TankMaintenance Battery Maintenance BatteriesLOW Battery SHUT-DOWN To Charge BatteriesTo Remove Batteries To Replace BatteriesSqueegee Adjustment To Adjust Squeegee PitchTo Replace or Rotate Rear Squeegee Blades To Remove Squeegee AssemblyTo Replace or Rotate Front Squeegee Blades Adjusting the Side Squeegee Deflection Side Squeegee AdjustmentTo Replace or Rotate Side Squeegee Blades Replacing or Installing Scrub Brushes Scrub BrushesUncoated Floors Finished FloorsFloat Switch Solution StrainerBrake Adjustment Steering Chain Tensioner AdjustmentVacuum Motor Changing Vacuum MotorBrush Motor Brush Motor Carbon Brush ReplacementChanging Brush Motors Traction Motor Traction Motor Carbon Brush ReplacmentFuse Circuit BreakersSqueegee Actuator REMOVAL/REPLACEMENT Squeegee Actuator AdjustmentScrub Deck Actuator REMOVAL/REPLACEMENT Scrub Deck Actuator AdjustmentTransporting Machine Towing or Pushing MachineMachine TIE-DOWNS Preparation for TransportingJacking Machine Machine JackingTo Jack UP Machine Machine StorageMaintenance Service Schedule Maintenance Before Each Work PeriodAfter Each Work Period HRSProblem Cause Error Code Machine TroubleshootingSolution Problem Cause Solution

10052530, SGJ32 specifications

The Windsor SGJ32, model 10052530, is a highly sophisticated and versatile industrial sewing machine engineered for optimal performance in various textile applications. Designed for heavy-duty usage, this model stands out due to its robust construction and innovative technologies that cater to the needs of modern manufacturing environments.

One of the defining features of the SGJ32 is its advanced stitching capabilities. The machine is equipped with a high-speed motor that enables it to achieve impressive stitching rates, allowing users to maximize productivity. It can seamlessly handle a wide range of fabrics, from lightweight materials to heavy-duty textiles, making it an ideal choice for diverse sewing applications, including upholstery, outdoor gear, and garment production.

In terms of technology, the SGJ32 integrates computer numerical control (CNC) systems that enhance precision and repeatability in stitching. This technology allows for intricate designs and patterns to be produced with high accuracy, reducing the margin for error and ensuring consistent quality across batches. Additionally, the machine features a user-friendly interface with touch controls, making it easier for operators to adjust settings quickly and efficiently.

Another notable characteristic of the Windsor SGJ32 is its adaptability. The machine can be easily customized with various attachments and accessories, empowering users to tackle specific tasks and improve workflow. Its adjustable stitch length and width provide further versatility, enabling operators to switch between different sewing techniques without hassle.

The construction of the SGJ32 is another key aspect that contributes to its reliability. Built from high-quality materials, the machine is designed to withstand the rigors of continuous operation while minimizing wear and tear. This durability not only extends the lifespan of the equipment but also ensures lower maintenance costs over time.

Moreover, the SGJ32 incorporates safety features such as automatic needle positioning and a thread trimmer, which enhance operational safety and ease of use. These features reduce the risk of accidents and streamline the sewing process, allowing operators to focus on their craft without unnecessary distractions.

In conclusion, the Windsor SGJ32, model 10052530, is a powerful, versatile, and technologically advanced sewing machine that caters to a wide range of industrial applications. With its high-speed capabilities, precision control, adaptability, and robust construction, it is an essential tool for manufacturers seeking to improve efficiency and maintain quality in their production processes.