Wayne-Dalton 8800 installation instructions Stacking Sections, Tools Needed, Screws

Page 14

 

Vertical Track and Wall Angle

 

Installation Continued....

 

 

Tools Needed:

Position the left hand vertical track assembly

 

over the rollers of the bottom section. Make

 

sure the counterbalance cable is located

 

between the rollers and the door jamb. Drill

 

3/16” pilot holes for the lag screws. Loosely

 

fasten the vertical track assembly to the jamb

 

using 5/16” x 2” lag screws. Tighten

 

bottom lag screw securing vertical track

 

assembly to jamb, to maintain 5/8” spacing.

 

Repeat for the right hand side.

 

Tighten the 1/4” x 5/8” carriage bolts and 1/4”

 

flange hex nuts of each clip plates.

 

Hang counterbalance cables over vertical track

 

assemblies.

 

 

Wall angle

5/16 x 2” LAG

SCREWS

wall angle

ASSEMBLY

BOTTOM

SECTION

wall angle

hole

selection

vertical track

3/8 - 5/8”

roller

wall angle

vertical track

5/16” x 2” lag bolt

12

Stacking Sections

 

 

 

Tools Needed:

NOTE: For door section identification see page 4.

 

NOTE: Make sure hinges are flipped down, when

 

 

 

Power Drill

stacking another section on top.

 

With assistance, lift second section and guide

 

 

 

7/16” Socket

roller into the left vertical track. Stack this

 

Driver

section into the opening by hooking the roller

lock section

 

into the left hand vertical track and lowering

 

 

 

the section onto the bottom section, as shown.

 

 

Insert a roller into the proper, uninstalled right

 

 

hand end hinge, and place the roller into the

 

 

right hand vertical track. Lower the roller and

 

 

hinge into the proper position over the section,

 

 

and attach to the section in the same manner

 

 

the left hand end hinge was attached in step 7.

 

 

Keeping the ends of the sections aligned, install

 

 

remaining section(s), except top section, in same

 

 

manner. Now flip up hinge leaf, hold tight against

 

 

section, and fasten center hinges first, and end

 

 

hinges last, using (2) 1/4” x 7/8” self drilling

 

 

screws. Repeat for other section(s) except top

 

 

section.

 

 

IMPORTANT: Push & hold the hinge leaf

 

 

against section while securing with 1/4” x

 

 

5/8” self tapping screws.

 

 

NOTE: Install lock at this time (sold separately)

 

 

see instructions in OPTIONAL SIDE LOCK

 

 

INSTALLATION on page 24.

 

14

 

 

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Portland Source Plant Wayne-Dalton CorpTable of Contents Package Contents Door Section Identification P1 Removing An Old Door Tools RequiredMounting pad to structurally sound Preparing the OpeningFailure to securely attach a suitable Resulting in severe or fatal injuryInstallation Sideroom requirementsOr 8’-0 in height do not require Cutting Vertical TrackImportant Doors that are 7’-0 Cutting the vertical trackBrackets Track and Installing Wall AngleInstalling Fully Adjustable Jamb Important Right and left hand is To Bottom BracketsBottom Brackets Always determined from insideImportant When Placing Rollers HingesLift handle outside Top BracketLift Handle Lift handle insideBottom Section Vertical Track and Wall AngleScrews Stacking SectionsTools Needed Roller Nail Top SectionRepeat for opposite side Top section 4 from top 11/16 to Edge of top sectionBefore attempting to raise door Adjusting Top BracketsImportant Failure to remove nail Could cause permanent damage toIs always determined from inside Center Bearing BracketImportant Right and left hand Torsion Spring Assembly SpacingRequired, contact Wayne-Dalton Corp. for free replacements Nylon Center BushingFor Spring Winding Counterbalance CablesSecuring Door Winding Torsion Springs Parallel and within 3/4 Maximum of door edge Rear SupportKeep horizontal track Otherwise door could fall Resulting in severe injury orPerforated Angle Horizontal TrackAngle Brace Side Lock Pull RopeTrolley Operator Following cleaning solution is recommended CleaningCleaning Your Garage Door Limited Warranty Model Thank you for your purchase

8800 specifications

The Wayne-Dalton 8800 is a premium insulated steel garage door designed for both residential and commercial applications. Renowned for its superior durability and energy efficiency, this model stands out as an ideal choice for homeowners and businesses looking to enhance their property’s aesthetic and functional characteristics.

One of the primary features of the Wayne-Dalton 8800 door is its construction. The door is constructed with a robust steel frame filled with high-density polystyrene insulation. This insulation provides a remarkable thermal performance, helping to reduce energy costs and maintain comfortable temperatures throughout the year. With an R-value of up to 14.5, the 8800 door ensures that indoor environments remain stable, minimizing the heat loss or gain typical of garage spaces.

In terms of design, the 8800 model is available in various styles and colors, allowing homeowners to customize their doors to match their personal taste and architectural preferences. This door is typically offered in a smooth finish or with a wood-grain texture, providing options for both modern and classic aesthetics. Additionally, the door features steel construction with a sophisticated exterior, ensuring it withstands the test of time while looking great.

Safety is paramount in the Wayne-Dalton 8800 design. Equipped with safety features such as pinch-resistant finger protection, the door helps prevent injuries, making it a family-friendly choice. Its advanced torsion spring system, which is designed for longevity, further enhances safety, ensuring smooth operation and reducing the risk of accidents.

Additionally, the Wayne-Dalton 8800 incorporates innovative technology to improve convenience and usability. The door can be fitted with various automatic opening mechanisms, including Wi-Fi-enabled garage door openers that allow for remote access via smartphones. This technology not only adds an element of convenience but also enhances security, allowing homeowners to monitor access and control their garage door from anywhere.

Overall, the Wayne-Dalton 8800 combines practical features, advanced technology, and customizable design, making it an excellent choice for those seeking a reliable and stylish garage door solution. With its focus on energy efficiency, safety, and overall functionality, it remains a leading option in the market for both residential and commercial use.
Top Page Image Contents