Wayne-Dalton 8800 installation instructions Center Bearing Bracket, Important Right and left hand

Page 17

 

 

16

Torsion End Bearing Brackets

Tools Needed:

IMPORTANT: Right and left hand

Power Drill

is always determined from inside

the garage looking out.

 

7/16” Socket

End bearing brackets are right and left.

Driver

Using the upper slots in the end bearing

9/16” Socket

bracket, position above the flagangle and

secure the end bearing bracket to the

 

horizontal angle using

Ratchet Wrench

(2) 3/8”- 16 x 3/4” hex head bolts and (2)

3/8”- 16 hex nuts.

 

9/16” Wrench

Once the bracket is secured to the horizontal

 

Step Ladder

angle, secure the top of the end bearing

bracket to the jamb using (2) 5/16” x 2” lag

 

screws. Repeat for other side.

 

 

Left end bearing

bracket

Horizontal angle

(2) 3/8”- 16 x 3/4” hex head bolts

(2) 5/16” x 2” lag screws

(2) 3/8”- 16

hex nuts

INSTALLATION

17

 

Mounting surface

Vertical line

Center Bearing Bracket

 

 

Center bearing

 

Equal distance

bracket

Tools Needed:

Measure to locate the center of the door and

Horizontal

 

mark a vertical pencil line on the mounting

 

 

 

Power Drill

surface above the door, to indicate the center

line

 

Center of end

 

line of the door. Then, measure from the center

 

 

 

7/16” Socket

of the bearing, in one of the end bearing

bearing bracket

 

 

 

brackets, DOWN to the top of the door. Using

 

 

Driver

that dimension, measure UP from the top of

 

 

 

the door and mark a horizontal pencil line on

 

 

Level

the mounting surface, intersecting the vertical

 

 

 

pencil line. Now align the edge of the center

 

 

Tape Measure

bearing bracket along the vertical pencil line

 

 

on the mounting surface. Center the bearing

 

 

 

 

 

Pencil

bracket on the horizontal line. This will ensure

Vertical

Center

the torsion tube is level between the center

 

and end bearing brackets. Attach the center

line

bearing

 

 

bracket

1/4” Torx Bit

bearing bracket, in this location, to the mounting

Mounting

 

 

surface, using (2) 5/16” x 2” lag screws and

surface

(2) 5/16” x 2”

Step Ladder

(1) 5/16” x 2” tamper-resistant lag screw.

 

lag screws

 

 

 

 

IMPORTANT: Use the 5/16” x 2” tamper-

Horizontal line

 

 

resistant lag screw ONLY if mounting

 

 

 

surface mounted over masonry.

 

 

 

Tamper-resistant lag screw MUST be

 

 

 

attached through the bottom hole

 

 

 

of the center bearing bracket.

 

 

 

 

 

(1) 5/16” x 2”

 

 

Tamper-resistant lag screw

 

 

or (1) 5/16” x 2” LAG Screw

17

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Wayne-Dalton Corp Portland Source PlantTable of Contents Package Contents Door Section Identification Tools Required P1 Removing An Old DoorFailure to securely attach a suitable Preparing the OpeningMounting pad to structurally sound Resulting in severe or fatal injurySideroom requirements InstallationImportant Doors that are 7’-0 Cutting Vertical TrackOr 8’-0 in height do not require Cutting the vertical trackBrackets Track and Installing Wall AngleInstalling Fully Adjustable Jamb Bottom Brackets To Bottom BracketsImportant Right and left hand is Always determined from insideHinges Important When Placing RollersLift Handle Top BracketLift handle outside Lift handle insideVertical Track and Wall Angle Bottom SectionScrews Stacking SectionsTools Needed Repeat for opposite side Top SectionRoller Nail Top section 4 from top 11/16 to Edge of top sectionImportant Failure to remove nail Adjusting Top BracketsBefore attempting to raise door Could cause permanent damage toIs always determined from inside Center Bearing BracketImportant Right and left hand Spacing Torsion Spring AssemblyNylon Center Bushing Required, contact Wayne-Dalton Corp. for free replacementsFor Spring Winding Counterbalance CablesSecuring Door Winding Torsion Springs Keep horizontal track Rear SupportParallel and within 3/4 Maximum of door edge Otherwise door could fall Resulting in severe injury orPerforated Angle Horizontal TrackAngle Brace Pull Rope Side LockTrolley Operator Following cleaning solution is recommended CleaningCleaning Your Garage Door Limited Warranty Model Thank you for your purchase

8800 specifications

The Wayne-Dalton 8800 is a premium insulated steel garage door designed for both residential and commercial applications. Renowned for its superior durability and energy efficiency, this model stands out as an ideal choice for homeowners and businesses looking to enhance their property’s aesthetic and functional characteristics.

One of the primary features of the Wayne-Dalton 8800 door is its construction. The door is constructed with a robust steel frame filled with high-density polystyrene insulation. This insulation provides a remarkable thermal performance, helping to reduce energy costs and maintain comfortable temperatures throughout the year. With an R-value of up to 14.5, the 8800 door ensures that indoor environments remain stable, minimizing the heat loss or gain typical of garage spaces.

In terms of design, the 8800 model is available in various styles and colors, allowing homeowners to customize their doors to match their personal taste and architectural preferences. This door is typically offered in a smooth finish or with a wood-grain texture, providing options for both modern and classic aesthetics. Additionally, the door features steel construction with a sophisticated exterior, ensuring it withstands the test of time while looking great.

Safety is paramount in the Wayne-Dalton 8800 design. Equipped with safety features such as pinch-resistant finger protection, the door helps prevent injuries, making it a family-friendly choice. Its advanced torsion spring system, which is designed for longevity, further enhances safety, ensuring smooth operation and reducing the risk of accidents.

Additionally, the Wayne-Dalton 8800 incorporates innovative technology to improve convenience and usability. The door can be fitted with various automatic opening mechanisms, including Wi-Fi-enabled garage door openers that allow for remote access via smartphones. This technology not only adds an element of convenience but also enhances security, allowing homeowners to monitor access and control their garage door from anywhere.

Overall, the Wayne-Dalton 8800 combines practical features, advanced technology, and customizable design, making it an excellent choice for those seeking a reliable and stylish garage door solution. With its focus on energy efficiency, safety, and overall functionality, it remains a leading option in the market for both residential and commercial use.
Top Page Image Contents