Wayne-Dalton 8800 installation instructions Horizontal Track, Angle Brace, Perforated Angle

Page 23

 

Rear Support Continued...

 

 

 

Tools Needed:

To adjust spring tension, fully close door. Apply

Sound Framing Members

 

 

 

 

 

locking pliers to track above third roller. Insert

 

 

 

 

a winding bar into the winding cone. Push

 

 

 

 

upward on the winding bar while carefully

 

 

 

 

loosening the set screws in the winding cone.

perforated

 

 

 

WARNING

perforated ANGLE -BOLTED

 

 

ANGLE BRACE

 

 

USING (2) 5/16” X 1-5/8”

 

 

 

 

 

 

BE PREPARED TO SUPPORT THE

 

HEX HEAD LAG SCREWS

 

 

 

TO CEILING MEMBER AND

 

 

FULL FORCE OF THE TORSION

 

PARALLEL TO WIDTH OF DOOR

 

 

SPRING ONCE THE SET SCREWS

 

 

 

 

ARE LOOSE.

 

 

 

 

Carefully adjust spring tension 1/4 turn.

HORIZONTAL TRACK

BOLT MUST EXTEND INTO

 

 

 

THE TRACK TO SERVE AS

 

 

Retighten both set screws in the winding cone

 

 

 

 

A ROLLER STOP

 

 

and repeat for the other side. Recheck door

 

 

 

balance DO NOT ADJUST MORE THAN 1/2

 

 

 

 

TURN FROM THE RECOMMENDED NUMBER OF

 

 

 

 

TURNS. If door still does not balance correctly,

Sound Framing Members

INSTALLATION

 

contact a qualified door agency.

 

 

 

 

 

 

 

If the door still does not operate easily, lower

 

 

 

 

the door into the closed position, UNWIND

 

 

 

 

THE SPRING(S) FULLY (Refer to “P1” on page

ANGLE BRACE

 

 

 

5 “Removing an old door”) and recheck the

perforated ANGLE -BOLTED

 

 

following items:

 

 

 

1.) Check the door for level.

 

USING (2) 5/16” X 1-5/8”

 

 

 

HEX HEAD LAG SCREWS

 

 

2.) Check the torsion tube for level.

 

TO CEILING MEMBER AND

 

 

 

PARALLEL TO WIDTH OF DOOR

 

 

3.) Check the track spacing.

HORIZONTAL TRACK

BOLT MUST EXTEND INTO

 

 

 

 

 

 

4.) Check the counterbalance cables for

 

THE TRACK TO SERVE AS

 

 

 

A ROLLER STOP

 

 

equal tension.

 

 

 

 

 

 

 

5.) Check the track for potential

PERFORATED ANGLE

 

 

 

 

 

 

 

obstruction of the rollers.

 

 

 

 

6.) Clamp locking pliers onto track and

 

weather

 

 

rewind springs.

 

 

 

 

 

seal

 

 

IMPORTANT: If door still does not

 

 

 

 

operate properly, then contact a

 

 

 

 

qualified door agency.

 

jamb

 

 

 

(3) 5/16” BOLTS

permanently attached

 

 

 

& NUTS

 

 

 

weather seal

 

 

 

 

 

 

 

 

23

 

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Wayne-Dalton Corp Portland Source PlantTable of Contents Package Contents Door Section Identification Tools Required P1 Removing An Old DoorResulting in severe or fatal injury Preparing the OpeningFailure to securely attach a suitable Mounting pad to structurally soundSideroom requirements InstallationCutting the vertical track Cutting Vertical TrackImportant Doors that are 7’-0 Or 8’-0 in height do not requireBrackets Track and Installing Wall AngleInstalling Fully Adjustable Jamb Always determined from inside To Bottom BracketsBottom Brackets Important Right and left hand isHinges Important When Placing RollersLift handle inside Top BracketLift Handle Lift handle outsideVertical Track and Wall Angle Bottom SectionScrews Stacking SectionsTools Needed Top section 4 from top 11/16 to Edge of top section Top SectionRepeat for opposite side Roller NailCould cause permanent damage to Adjusting Top BracketsImportant Failure to remove nail Before attempting to raise doorIs always determined from inside Center Bearing BracketImportant Right and left hand Spacing Torsion Spring AssemblyNylon Center Bushing Required, contact Wayne-Dalton Corp. for free replacementsFor Spring Winding Counterbalance CablesSecuring Door Winding Torsion Springs Otherwise door could fall Resulting in severe injury or Rear SupportKeep horizontal track Parallel and within 3/4 Maximum of door edgePerforated Angle Horizontal TrackAngle Brace Pull Rope Side LockTrolley Operator Following cleaning solution is recommended CleaningCleaning Your Garage Door Limited Warranty Model Thank you for your purchase

8800 specifications

The Wayne-Dalton 8800 is a premium insulated steel garage door designed for both residential and commercial applications. Renowned for its superior durability and energy efficiency, this model stands out as an ideal choice for homeowners and businesses looking to enhance their property’s aesthetic and functional characteristics.

One of the primary features of the Wayne-Dalton 8800 door is its construction. The door is constructed with a robust steel frame filled with high-density polystyrene insulation. This insulation provides a remarkable thermal performance, helping to reduce energy costs and maintain comfortable temperatures throughout the year. With an R-value of up to 14.5, the 8800 door ensures that indoor environments remain stable, minimizing the heat loss or gain typical of garage spaces.

In terms of design, the 8800 model is available in various styles and colors, allowing homeowners to customize their doors to match their personal taste and architectural preferences. This door is typically offered in a smooth finish or with a wood-grain texture, providing options for both modern and classic aesthetics. Additionally, the door features steel construction with a sophisticated exterior, ensuring it withstands the test of time while looking great.

Safety is paramount in the Wayne-Dalton 8800 design. Equipped with safety features such as pinch-resistant finger protection, the door helps prevent injuries, making it a family-friendly choice. Its advanced torsion spring system, which is designed for longevity, further enhances safety, ensuring smooth operation and reducing the risk of accidents.

Additionally, the Wayne-Dalton 8800 incorporates innovative technology to improve convenience and usability. The door can be fitted with various automatic opening mechanisms, including Wi-Fi-enabled garage door openers that allow for remote access via smartphones. This technology not only adds an element of convenience but also enhances security, allowing homeowners to monitor access and control their garage door from anywhere.

Overall, the Wayne-Dalton 8800 combines practical features, advanced technology, and customizable design, making it an excellent choice for those seeking a reliable and stylish garage door solution. With its focus on energy efficiency, safety, and overall functionality, it remains a leading option in the market for both residential and commercial use.
Top Page Image Contents