Wayne-Dalton 8800 installation instructions Rear Support, Keep horizontal track, Death

Page 22

23

Rear Support

 

 

 

Tools Needed:

WARNING

DOOR IN THE

UP POSITION

 

 

Ratchet Wrench

Keep horizontal track

 

 

 

1/2” Socket

parallel and within 3/4”

 

maximum of door edge,

 

 

 

1/2” Wrench

otherwise door could fall,

 

 

resulting in severe injury or

 

(2) Vice Clamps

death.

 

Step Ladder

Raise the door until the top section and half

 

 

of the next section are in a horizontal position.

 

 

Do not raise door any further since rear of

 

 

horizontal track is not yet supported.

vice

 

WARNING

 

clamps

 

Raising door further can

 

 

result in door falling and

 

 

cause severe injury or death.

 

 

Clamp a pair of vice clamps on the vertical

 

 

tracks just above the second roller on one

 

 

side, just below the second roller on the other

 

 

side. This will prevent the door from raising or

 

 

lowering while installing the rear support.

vertical

 

 

 

Using perforated angle, 5/16” x 1-5/8” hex

TRACK

 

 

 

head lag screws and 5/16” bolts with nuts

 

 

(may not be supplied), fabricate rear support

 

 

for horizontal tracks. Attach horizontal tracks to

 

 

the rear supports with 5/16”- 18 x 1-1/4” hex

 

 

bolts and nuts (may not be supplied). Horizontal

 

 

tracks must be level and parallel with door.

 

 

NOTE: If rear supports are to be installed over

 

 

drywall, use 5/16” x 2” hex head lag screws

 

 

and make sure lag screws engaged solid

 

 

structural lumber.

 

 

NOTE: If an idrive® opener will be installed,

 

 

position horizontal tracks one hole above level

 

 

when securing it to rear supports.

 

 

Adjust weather seal (if necessary). Now

 

 

permanently attach the weather seal to both

 

 

door jambs and header. (Temporarily attached in

 

 

PREPARING THE OPENING on page 6-7.) Avoid

 

 

pushing weather seal too tightly against face

 

 

of door.

Edge

 

WARNING

 

 

Door

 

Prior to winding or making adjustments

1/2”- 5/8”

 

to the springs, ensure you’re winding in

 

 

 

the proper direction as stated in the

 

 

Installation Instructions. Otherwise,

 

 

the spring fittings may release from

Horizontal Track

 

spring if not wound in the proper

 

 

 

direction and could result in severe or

 

 

fatal injury.

 

22

 

 

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Portland Source Plant Wayne-Dalton CorpTable of Contents Package Contents Door Section Identification P1 Removing An Old Door Tools RequiredMounting pad to structurally sound Preparing the OpeningFailure to securely attach a suitable Resulting in severe or fatal injuryInstallation Sideroom requirementsOr 8’-0 in height do not require Cutting Vertical TrackImportant Doors that are 7’-0 Cutting the vertical trackInstalling Fully Adjustable Jamb Track and Installing Wall AngleBrackets Important Right and left hand is To Bottom BracketsBottom Brackets Always determined from insideImportant When Placing Rollers HingesLift handle outside Top BracketLift Handle Lift handle insideBottom Section Vertical Track and Wall AngleTools Needed Stacking SectionsScrews Roller Nail Top SectionRepeat for opposite side Top section 4 from top 11/16 to Edge of top sectionBefore attempting to raise door Adjusting Top BracketsImportant Failure to remove nail Could cause permanent damage toImportant Right and left hand Center Bearing BracketIs always determined from inside Torsion Spring Assembly SpacingRequired, contact Wayne-Dalton Corp. for free replacements Nylon Center BushingSecuring Door Counterbalance CablesFor Spring Winding Winding Torsion Springs Parallel and within 3/4 Maximum of door edge Rear SupportKeep horizontal track Otherwise door could fall Resulting in severe injury orAngle Brace Horizontal TrackPerforated Angle Side Lock Pull RopeTrolley Operator Cleaning Your Garage Door CleaningFollowing cleaning solution is recommended Limited Warranty Model Thank you for your purchase

8800 specifications

The Wayne-Dalton 8800 is a premium insulated steel garage door designed for both residential and commercial applications. Renowned for its superior durability and energy efficiency, this model stands out as an ideal choice for homeowners and businesses looking to enhance their property’s aesthetic and functional characteristics.

One of the primary features of the Wayne-Dalton 8800 door is its construction. The door is constructed with a robust steel frame filled with high-density polystyrene insulation. This insulation provides a remarkable thermal performance, helping to reduce energy costs and maintain comfortable temperatures throughout the year. With an R-value of up to 14.5, the 8800 door ensures that indoor environments remain stable, minimizing the heat loss or gain typical of garage spaces.

In terms of design, the 8800 model is available in various styles and colors, allowing homeowners to customize their doors to match their personal taste and architectural preferences. This door is typically offered in a smooth finish or with a wood-grain texture, providing options for both modern and classic aesthetics. Additionally, the door features steel construction with a sophisticated exterior, ensuring it withstands the test of time while looking great.

Safety is paramount in the Wayne-Dalton 8800 design. Equipped with safety features such as pinch-resistant finger protection, the door helps prevent injuries, making it a family-friendly choice. Its advanced torsion spring system, which is designed for longevity, further enhances safety, ensuring smooth operation and reducing the risk of accidents.

Additionally, the Wayne-Dalton 8800 incorporates innovative technology to improve convenience and usability. The door can be fitted with various automatic opening mechanisms, including Wi-Fi-enabled garage door openers that allow for remote access via smartphones. This technology not only adds an element of convenience but also enhances security, allowing homeowners to monitor access and control their garage door from anywhere.

Overall, the Wayne-Dalton 8800 combines practical features, advanced technology, and customizable design, making it an excellent choice for those seeking a reliable and stylish garage door solution. With its focus on energy efficiency, safety, and overall functionality, it remains a leading option in the market for both residential and commercial use.
Top Page Image Contents