Bacharach INSIGHT manual Operational Overview, Technical Characteristics

Page 5

Fyrite® INSIGHT

1.3 Operational Overview

Pressing the PWR button turns the analyzer ON. Note that there is a warm-up period of 60 seconds that must elapse before the analyzer can be used.

To perform a combustion test, choose a fuel code that corresponds to the fuel being burned by the appliance being tested (Section 4.3), and then press the RUN/HOLD button to place the analyzer into its Run Mode. Begin testing by inserting the analyzer’s probe tube into the flue-gas stream of the appliance under test. The analyzer will monitor the flue gas and display measured and calculated values that are relative to the combustion process. These values are displayed on the analyzer’s LCD, and are chosen for display by pressing the Increment () and Decrement () buttons.

Pressing the RUN/HOLD button during a test will freeze all measured and calculated values at their current levels. Pressing the RUN/HOLD button again resumes testing.

A backlight enables an operator to read the display in dimly-lit areas. Pressing the PWR button turns the backlight ON and OFF.

An optional power saver function will shut the analyzer OFF after a set time period of inactivity. This feature is disabled if the CO value is greater than 50 ppm or the O2 value is less than 16.0%.

Press the PWR button for at least two seconds to power the analyzer OFF. Note that there is a 5 second delay before the analyzer actually turns OFF, during which time the unit can be kept ON by pressing the RUN/HOLD button. There is a CO purge feature that keeps the analyzer’s pump running until the measured CO level drops below 50 ppm.

Fyrite® INSIGHT

2.0 TECHNICAL CHARACTERISTICS

The Analyzer measures & displays:

Primary/Ambient Air Temperature

-4 to 600 °F (-20 to 316°C)

Oxygen

0.1 to 20.9% O2

Stack Temperature

-4 to 1202 °F (–20 to 650 °C)

Carbon Monoxide

0 to 2000 ppm CO

Differential Pressure/Draft

± 100 inwc

The Analyzer computes & displays:

 

Combustion Efficiency

0.1 to 100%

Carbon Dioxide

0.1 to a fuel dependent

 

maximum value in %

CO referenced to %O2

0 to 9,999 ppm

Excess Air

0 to 250%

Fuel Selection

 

• Natural Gas

• Propane

• Oil #2

• Kerosene

• Oil #4

• Wood

• Oil #6

• Coal

Normal Operating Conditions:

 

Temperature

 

• Analyzer

32 to 104 °F (0 to 40 °C)

• Probe

1,000 °F max (538 °C) at

 

5" insertion

Humidity

15 to 90% RH, Non-Condensing

Dimensions

Weight

7.9 in (20.1 cm) Height

1lb. (0.45 kg)

3.6 in (9.1 cm) Width

 

2.3 in (5.8 cm) Depth

 

4

Instruction 24-9460

 

Instruction 24-9460

5

Image 5
Contents Fyrite Insight Table of Contents Fyrite Insight IntroductionFyrite Insight Features & Benefits Operational Overview Technical CharacteristicsPower Setting UP the AnalyzerConnecting the Probe Hose & Thermo- couple Preliminary StepsInsight Entering Setup Setup ModeTemperature Units Front Panel Push ButtonsClock Pressure Units5 O2 Reference Print Pressure9 Run/Hold Format UsernameCAL Reminder Period Language SelectionButton Sound Date Format Inactivity TimeoutPost-Purge Period Operation Analyzer Power On & Warm UpOperating Tips Fuel SelectionPerforming a Combustion Test Sampling PointMaking a Draft / Pressure Measurement Saving Test Data Temperature MeasurementEnding a Combustion Test Emptying the Water TrapMemory Powering OFF the Analyzer & PurgingLow Battery Alarm Press the Print F1 button to begin print- ing Fyrite User Software InstallationPrinting Test Data Windows Vista Operating System Fyrite User Software Description Calibration & MaintenanceSmart Sensors Starting a CalibrationMaterials Required Pressure Sensor CalibrationStack Calibration ProcedureTS-Zero Procedure TA-Zero Procedure TS-Span ProcedureAir Calibration Material RequiredCO Sensor Calibration TA-Span ProcedureMaintenance Fyrite Insight Disassembly Water Trap / Filter O2 Sensor ReplacementTools Required CO Sensor ReplacementThermocouple Replacement Cleaning the Probe Gas Pump ReplacementError Messages Parts & Tools RequiredStatus Screen Diagnostics ScreenUnited States Pennsylvania Service CentersCanada MéxicoHeadquarters Hunt Valley Circle, New Kensington, PA

INSIGHT specifications

Bacharach INSIGHT is a cutting-edge platform designed for HVAC professionals and building management teams, providing real-time insights and analytics for optimal system performance. Offering a seamless integration of hardware and software, INSIGHT enhances operational efficiency by transforming traditional data management paradigms.

One of the standout features of Bacharach INSIGHT is its user-friendly interface, which enables users to visualize data in an easily digestible format. The platform presents key metrics, historical trends, and system alerts, empowering users to make informed decisions quickly. This accessibility is crucial for technicians and managers who need to identify potential issues before they escalate, ensuring systems run smoothly and effectively.

Another significant characteristic of Bacharach INSIGHT is its advanced data analytics capabilities. The platform leverages machine learning algorithms to analyze performance data, identify patterns, and predict maintenance needs. This proactive approach minimizes downtime and extends the lifespan of HVAC systems, resulting in cost savings for organizations.

INSIGHT also incorporates IoT technologies, allowing for real-time data collection from various connected devices across an HVAC system. This integration ensures that users have access to accurate and timely information, facilitating immediate responses to any irregularities. The use of cloud technology enables data storage and access from anywhere, promoting collaboration among team members and stakeholders.

The platform is designed with scalability in mind, accommodating small businesses with singular HVAC units as well as large enterprises with complex, multi-site systems. This flexibility means that as organizations grow, Bacharach INSIGHT can adapt to their changing needs without requiring extensive modifications.

Furthermore, user customization options allow for tailored dashboards and alerts, ensuring that each team can focus on the most relevant metrics for their operations. This adaptability contributes to improved user experience, enhancing system usability and engagement.

In summary, Bacharach INSIGHT combines intuitive design, powerful analytics, IoT integration, and scalability to redefine HVAC management. By equipping users with actionable insights and fostering proactive maintenance practices, INSIGHT positions organizations to optimize their energy use, reduce costs, and improve overall system reliability. This innovative platform is pioneering a new era for HVAC professionals, facilitating smarter building management with robust, real-time analytics.