Desa VN2000BB, VGN30B installation manual Operating Heater, Pilot

Page 18

18

OPERATING HEATER

Continued

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information at the top of page 17. If you don’t smell gas, go to the next step.

5.Press in control knob and turn counterclockwise C-clockwiseto the PILOT position. Keep control knob pressed in for five (5) seconds (see Figure 15, page 17).

Note: You may be running this heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds. This will allow air to bleed from the gas system.

If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs.

6.With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the front of burner. The burner and pilot are located behind the heat shield. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, refer to Troubleshooting, pages 21 through

24.Also contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure, page 19.

 

Ignitor Electrode

Thermocouple

Pilot Burner

Pilot

Figure 16 - Pilot

GRH/OV 007G

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

Note: If pilot goes out, repeat steps 3 through 7.

8.Turn control knob counterclockwise C-clockwiseto the LOW position. The main burner should light. Set control knob to any heat level between HIGH and LOW. To turn control knob from LOW to a higher setting, press in the

control knob and turn counterclockwise C-clockwise .

Note: Both HIGH and LOW are locked positions. You must press in control knob before turning it from these positions.

CAUTION

Do not try to adjust heating levels by using the manual shutoff valve.

100099

Image 18
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASContents SafetySafety Information Unpacking Product IdentificationLocal Codes ProductVentilation Fresh AIR ForCombustion Producing Adequate VentilationFresh AIR Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Fresh AIR for Combustion and Ventilation Ventilation AIRVentilation Air From Inside Building Ventilation AIR Ventilation Air From OutdoorsCheck GAS Type Installing To WallInstallation Items Locating Heater16 3/ 4 VGN30B CeilingRight FloorRemoving Front Panel Of Heater Installing Heater to WallMounting Bracket Methods For Attaching Mounting Bracket To WallMarking Screw Locations Attaching Mounting Bracket To WallInstalling Bottom Mounting Screws Placing Heater On Mounting BracketConnecting to GAS Supply Connections Pressure Testing GAS Supply Piping SystemChecking GAS Servicing. Correct all leaks at oncePressure Testing Heater GAS Connections CheckingOperating HeaterOperating Heater PilotPilot Flame Pattern InspectingBurner Shutting Off HeaterCorrect Flame Pattern AT High Position Inspecting BurnerBurner Flame Pattern Incorrect Flame Pattern AT High PositionTrouble Shooting CleaningMaintenance ODS/PILOT and BurnerSee Cleaning TROUBLE- ShootingFrom Ing statement at TopTechnical Service Service HintsVGN30B Replacement Parts Parts Under WarrantyParts Not Under Warranty Accessories Manual ShutoffFloor Mounting Stand ODS/Pilot VGN30B Parts List KEY Part Number Description QTY12-2 12-1 VN2000BB Warranty Information Limited Warranty Vanguard VENT-FREE Heaters