Empire Comfort Systems VFDR24LBP-1 VFDR,T,M18,24 & VFDR18LB10 LOG Placement 5 LOG SET

Page 13

VFD(R,T,M)(18,24) & VFDR18LB10 LOG PLACEMENT (5 LOG SET)

Before you begin: if you are installing logs onto the VFD(R,T,M)18 or VFD(R,T,M)24 models, this burner assembly is supplied with a set of five ceramic fiber logs. Do not handle these logs with your bare hands! Always wear gloves to prevent skin irritation from ceramic fibers. After handling logs, wash your hands gently with soap and water to remove any traces of fibers.

The positioning of the logs is critical to the safe and clean operation of this burner assembly. Sooting and other problems may result if the logs are not properly and firmly positioned on the burner assembly. Refer to Figure 12 and Figure 13 and corresponding WARNING: when completing following log placement instruc- tions.

1.Place front logs (#1 and #2) between front grate flange and main burner. Align notches on front logs with locator tabs in base.

2.Place middle log (#3) between front and rear loop of burner. Note: Do not place log on top of pilot assembly.

3.Place rear log (#4) on rear log shelf. Bottom flange of log must be placed between the log shelf and burner tube.

4.This step is optional for VFDR18LB10 log sets. Place front twig (#5) onto (#1) log and flat area on (#3) log. The bottom of the front twig is to be placed behind the grate tang that is second from the left.

EMBER MATERIAL PLACEMENT ON BURNER

5.After all logs are positioned properly, apply Rockwool ember material to the front burner port area. To apply, carefully separate the ember material into small amounts no larger than "dime size" pieces. Fluffed up pieces one layer thick on top of the burner generally works best, and will provide the best ember glow. Do not place ember material more than one layer thick. No more than (2) two small packets of ember material (part no. 15998) evenly placed on the burner, is recommended on VFDR18 and VFDR24 models. Using additional ember material will decrease the amount of ember glow effect. Extra ember material should be saved for future ember applications as necessary. See Figure 13.

Description

Part #

VFD(R,T,M)18 Embers

15998

VFD(R,T,M)24 Embers

15998

VFD(R,T,M)30 Embers

15999

Platinum Bright Embers

PE20-1

Note: A single layer of embers is to be used when applying Platinum Bright Embers (alone or in combination with stndard embers) to the burner.

4

5

3

2

1

Figure 12

WARNING: Failure to position the parts in accordance with this diagram or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

Attention: Do not use Figure 12 or Figure 13 to order logs. Refer to Parts Lists and Parts Views to order logs and/or ember material for your appropriate model.

Figure 13

23099-1-0707

Page 13

Image 13
Contents Installation Instructions Table of Contents Carbon Monoxide Poisoning MAY Lead to Death Important Safety InformationLP-GAS Warning Odor Safety Information for Users of LP-GASAccessories for VFDR, VFDT, & Vfdm Well Head Gas InstallationsAccessories for Vfdr only IntroductionModel BTU/hr Max. Rate Med. Rate Min. Rate Product SpecificationsBefore you get started General InformationMake sure you have received all parts High AltitudeGlass Doors ClearancesSidewall & Ceiling Clearances Figure Installing as a Vented ApplianceMantel Clearances Without Hood Figure Mantel Clearances with Hood FigureFireplace Preparation Combustible MaterialBefore Fully Installing the Appliance Installing AS a Vented ApplianceInstalling Damper Clamp Figure Pressure Testing of the Gas Supply System Installing a New Main Gas CockGAS Supply Recommended Gas Pipe DiameterEmber Material Placement on Burner VFDR,T,M18,24 & VFDR18LB10 LOG Placement 5 LOG SETEmber Material Placement on Burner VFDR,T,M30 LOG Placement 7 LOG SETMillivolt Valve for VFDR18LB10 Series Operation INSTRUCTIONS/FLAME AppearanceMillivolt Valve for Vfdr Series Thermostat Valve for Vfdt SeriesCheck System Operation Wiring Vfdr Models onlyRemote Receiver Millivolt SystemWhat to do if YOU Smell GAS VFDR18,24,30LB Lighting InstructionsVFDR18LB10N,P Lighting Instructions VFDT18,24,30LB Lighting Instructions VFDM18,24,30LB Lighting Instructions Incorrect Pilot Flame Pattern for Vfdr Pilot Flame CharacteristicsCorrect Pilot Flame Pattern for Vfdt & Vfdm Turn OFF Heater and Allow to Cool Before Cleaning Cleaning and ServicingHeater produces a whistling noise when main burner is lit Gas odor even when control knob is in OFF positionAppliance produces unwanted odors Appliance shuts off during use. Pilot stays onVfdr Series Parts List HOW to Order Repair PartsVfdr Series Parts View Index no Description VFDR18LB10 Parts ListVFDR18LB 10 Parts View Index Parts Numbers Description VFDT18LB VFDT24LB VFDT30LB Vfdt Series Parts ListVfdt Series Parts View Index Part Numbers Description VFDM18LB VFDM24LB VFDM30LB Vfdm Series Parts ListVfdm Series Parts View Service Notes