Empire Comfort Systems VFDM18LBN-1, VFDT24LBN-1 Introduction, Well Head Gas Installations

Page 5

INTRODUCTION

IMPORTANT: Read all instructions carefully before starting installation. Failure to follow these installation instructions may result in a possible fire hazard and will void the warranty.

Save this manual for future reference.

Please read this manual before installing and using the appliance.

Instructions to Installer

1.Installer must leave instruction manual with owner after installation.

2.Installer must have owner fill out and mail warranty card supplied with unvented room heater/vented decorative appliance.

3.Installer should show owner how to start and operate unvented room heater/vented decorative appliance.

Always consult your local Building Department regarding regulations, codes or ordinances which apply to the installation of an unvented room heater/vented decorative appliance.

This appliance may be installed in an aftermarket* manufactured (mobile) home, where not prohibited by state or local codes.

*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

Solid-fuels shall not be burned in a fireplace where a vented decorative appliance is installed.

A vented decorative appliance must be installed only in a solid- fuel burning fireplace with a working flue and constructed of non- combustible material.

Any alteration of the original design, installed other than as shown in these instructions oruse with a type of gas not shown on the rating plate is the responsibility of the person and company making the change.

Important

All correspondence should refer to complete Model Number, Serial Number and type of gas.

Attention: During initial use of log you will detect an odor as the log is cured.

Notice: During initial firing of this unit, its paint will bake out, and smoke will occur. To prevent triggering of smoke alarms, ventilate the room in which the unit is installed.

WARNING: This appliance is for installation only in a solid- fuel burning masonry or UL127 factory-built fireplace or in a listed ventless firebox enclosure. It has been design certified for these installations. Exception: DO NOT install this appliance in a factory-built fireplace that includes instructions stating it has not been tested or should not be used with unvented gas logs.

WARNING: Any modification to this unvented gas heater or its controls can be dangerous. Improper installation or use of the heater can cause serious injury or death from fire, burns, explosion or carbon monoxide poisoning.

Well Head Gas Installations

Some natural gas utilities use "well head" gas. This may affect the Btu output of the unit. Contact the gas company for the heating value. Contact the manufacturer or your gas company before changing spud/orifice size.

ACCESSORIES for VFDR, VFDT, & VFDM

 

Description

Color

EK-1

Embers Kit

 

PE-20

Platinum Embers

 

ELH-1

Fireplace Hood for Vent-Free Logs

Black

ELH-2

Fireplace Hood for Vent-Free Logs

Brass

ACCESSORIES for VFDR ONLY

 

FRBC

Battery Operated Remote Control

 

FRBTC

Battery Operated Remote Control with Thermostat

FREC

Electric Remote Control

 

FWS

Wall Switch

 

TRW

Remote Wall Thermostat

 

TMV

Wall Thermostat, Millivolt - Reed Switch

 

23099-1-0707

Page 5

Image 5
Contents Installation Instructions Table of Contents Carbon Monoxide Poisoning MAY Lead to Death Important Safety InformationLP-GAS Warning Odor Safety Information for Users of LP-GASAccessories for VFDR, VFDT, & Vfdm Well Head Gas InstallationsAccessories for Vfdr only IntroductionModel BTU/hr Max. Rate Med. Rate Min. Rate Product SpecificationsBefore you get started General InformationMake sure you have received all parts High AltitudeGlass Doors ClearancesSidewall & Ceiling Clearances Figure Installing as a Vented ApplianceMantel Clearances Without Hood Figure Mantel Clearances with Hood FigureFireplace Preparation Combustible MaterialInstalling Damper Clamp Figure Installing AS a Vented ApplianceBefore Fully Installing the Appliance Pressure Testing of the Gas Supply System Installing a New Main Gas CockGAS Supply Recommended Gas Pipe DiameterEmber Material Placement on Burner VFDR,T,M18,24 & VFDR18LB10 LOG Placement 5 LOG SETEmber Material Placement on Burner VFDR,T,M30 LOG Placement 7 LOG SETMillivolt Valve for VFDR18LB10 Series Operation INSTRUCTIONS/FLAME AppearanceMillivolt Valve for Vfdr Series Thermostat Valve for Vfdt SeriesCheck System Operation Wiring Vfdr Models onlyRemote Receiver Millivolt SystemWhat to do if YOU Smell GAS VFDR18,24,30LB Lighting InstructionsVFDR18LB10N,P Lighting Instructions VFDT18,24,30LB Lighting Instructions VFDM18,24,30LB Lighting Instructions Correct Pilot Flame Pattern for Vfdt & Vfdm Pilot Flame CharacteristicsIncorrect Pilot Flame Pattern for Vfdr Turn OFF Heater and Allow to Cool Before Cleaning Cleaning and ServicingHeater produces a whistling noise when main burner is lit Gas odor even when control knob is in OFF positionAppliance produces unwanted odors Appliance shuts off during use. Pilot stays onVfdr Series Parts List HOW to Order Repair PartsVfdr Series Parts View Index no Description VFDR18LB10 Parts ListVFDR18LB 10 Parts View Index Parts Numbers Description VFDT18LB VFDT24LB VFDT30LB Vfdt Series Parts ListVfdt Series Parts View Index Part Numbers Description VFDM18LB VFDM24LB VFDM30LB Vfdm Series Parts ListVfdm Series Parts View Service Notes