Empire Comfort Systems VFDR30LBN-1, VFDT24LBN-1 Wiring Vfdr Models only, Check System Operation

Page 16

WIRING - VFDR MODELS ONLY

Thermostats are not approved on vented decorative appliances.

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

18", 24" and 30" Gas Logs (Millivolt) thermopile is self powered gas valve and does not require 110 volts. See Figure to provide optional wall switch, thermostat, or remote control. Maximum length of 20 feet of 16 AWG to conductor wires is to be used with all optional switches.

Check System Operation

Millivolt system and all individual components may be checked with a millivolt meter 0-1000 MV range.

Remote Receiver

Use the following steps to place the remote receiver adjacent to the gas valve.

Attention:

1.The remote receiver can not be placed behind the gas valve and burner assembly.

2.When facing the appliance, the remote receiver must be placed to the right of the gas valve and burner assembly.

Note: Do not let remote control receiver come in contact with

WIRING DIAGRAM

(OPTIONAL) THERMOSTAT (FACULATIVE) THERMOSTAT

burner assembly.

On circulating vent-free firebox, install remote control receiver behind bottom louver.

Refer to remote control installation and operating instructions for more details on remote control.

750 Millivolt System

When you ignite the pilot, the thermocouple produces millivolts (electrical current) which energizes the magnet in the gas valve. After 30 seconds to 1 minute time period you can release the gas control knob and the pilot will stay ON. Allow your pilot flame to operate an additional one (1) to two (2) minutes before you turn the gas control knob from the PILOT position to the ON position. This time period allows the millivolts (electrical current) to buildup to a sufficient level allowing the gas control to operate properly.

Millivolt Control

The valve regulator controls the burner pressure which should be checked at the pressure test point. Turn captured screw counter clockwise 2 or 3 turns and then place tubing to pressure gauge over test point (Use test point “A” closest to control knob). After taking pressure reading, be sure and turn captured screw clockwise firmly to re-seal. Do not over torque. Check for gas leaks.

REMOTE CONTROL RECEIVER/

THERMOSTAT/ CONTROLE E

DISTANCE DU RECEPTEUR

HN

(OPTIONAL) WALL SWITCH

GAS VALVE

INTERRUPTEUR MURAL

VALVE DE GAZ

(FACULTATIVE)

REMOTE/OFF/ON SWITCH

ADISTANCE/OUVERT/ FERME INTERRUPTEUR

(OPTIONAL) REMOTE CONTROL RECEIVER (FACULTATIVE) CONTROLE E DISTANCE DU RECEPTEUR

THERMOPILE

PILOT

VEILLEUSE

THERMOCOUPLE (LPG)

THERMOCOUPLE (NATURAL)

REMOTE/OFF/ON SWITCH

ADISTANCE/FERME/OUVERT INTERRUPTEUR

REMOTE

OFF

IF ANY OF THE ORIGINAL WIRE

ON

AS SUPPLIED WITH THIS UNIT

 

MUST BE REPLACED, IT MUST BE

 

REPLACED WITH NUMBER 18, 150°C

 

WIRE OR ITS EQUIVALENT.

 

SI UN DES FILS ELECTRIQUES

 

ORIGINAUX, VENANT DU FABRICANT

 

AVEC CETTE UNITE, DOIT ETRE

GAS VALVE

REMPLACE, VOUS DEVEZ LE

REMPLACER AVEC UN FIL

 

ELECTRIQUE DE NUMERO 18,

 

150 ° C DU L'EQUIVALENT.

Figure 20

Page 16

23099-1-0707

Image 16
Contents Installation Instructions Table of Contents Important Safety Information Carbon Monoxide Poisoning MAY Lead to DeathSafety Information for Users of LP-GAS LP-GAS Warning OdorWell Head Gas Installations Accessories for VFDR, VFDT, & VfdmAccessories for Vfdr only IntroductionProduct Specifications Model BTU/hr Max. Rate Med. Rate Min. RateGeneral Information Before you get startedMake sure you have received all parts High AltitudeClearances Glass DoorsInstalling as a Vented Appliance Sidewall & Ceiling Clearances FigureMantel Clearances Without Hood Figure Mantel Clearances with Hood FigureCombustible Material Fireplace PreparationBefore Fully Installing the Appliance Installing AS a Vented ApplianceInstalling Damper Clamp Figure Installing a New Main Gas Cock Pressure Testing of the Gas Supply SystemGAS Supply Recommended Gas Pipe DiameterVFDR,T,M18,24 & VFDR18LB10 LOG Placement 5 LOG SET Ember Material Placement on BurnerVFDR,T,M30 LOG Placement 7 LOG SET Ember Material Placement on BurnerOperation INSTRUCTIONS/FLAME Appearance Millivolt Valve for VFDR18LB10 SeriesMillivolt Valve for Vfdr Series Thermostat Valve for Vfdt SeriesWiring Vfdr Models only Check System OperationRemote Receiver Millivolt SystemVFDR18,24,30LB Lighting Instructions What to do if YOU Smell GASVFDR18LB10N,P Lighting Instructions VFDT18,24,30LB Lighting Instructions VFDM18,24,30LB Lighting Instructions Incorrect Pilot Flame Pattern for Vfdr Pilot Flame CharacteristicsCorrect Pilot Flame Pattern for Vfdt & Vfdm Cleaning and Servicing Turn OFF Heater and Allow to Cool Before CleaningGas odor even when control knob is in OFF position Heater produces a whistling noise when main burner is litAppliance produces unwanted odors Appliance shuts off during use. Pilot stays onHOW to Order Repair Parts Vfdr Series Parts ListVfdr Series Parts View VFDR18LB10 Parts List Index no DescriptionVFDR18LB 10 Parts View Vfdt Series Parts List Index Parts Numbers Description VFDT18LB VFDT24LB VFDT30LBVfdt Series Parts View Vfdm Series Parts List Index Part Numbers Description VFDM18LB VFDM24LB VFDM30LBVfdm Series Parts View Service Notes