Hearth and Home Technologies SL-350TRSI-AUE manual Installing Flue Components

Page 17

Í

Installing Flue Components

After determining which set of starting collars will be used (top or rear), follow flueing instructions accordingly.

Flueing Out the Rear Flue

Remove the rear collar seal cap by cutting the strap at each end (see Figure 18).

Next, remove the insulation from the rear flue, pull the heat shield out from outside of the heater.

WARNING: THE TOP FLUE COLLAR ! SEAL CAP MUST REMAIN ATTACHED TO THE TOP FLUE COLLAR IF THE FLUE SYSTEM IS ATTACHED TO THE REAR STARTING COLLARS. SEE FIGURE 18.

Flueing Out the Top Flue

Remove the top flue collar cover plate. Remove the seal cap and both pieces of insulation in the top collars (see Figure 18). Remove the heat shield inside the top collars from the outside of the heater.

!WARNING: THE REAR FLUE COL- LAR SEAL CAP MUST REMAIN AT- TACHED TO THE REAR FLUE COL- LARS IF THE FLUE SYSTEM IS AT- TACHED TO THE TOP STARTING COLLARS. SEE FIGURE 17.

!WARNING: FAILURE TO REMOVE INSULATION IN THE SET OF COL- LARS YOU ARE USING COULD CAUSE A FIRE.

!WARNING: YOU MUST LEAVE THE INSULATION IN PLACE IN THE SET OF COLLARS YOU ARE NOT USING.

Insert screwdriver

FLUEING OUT REAR

 

FLUEING OUT TOP

 

 

 

or similar object

 

SEAL

 

here to remove cap.

SEAL

INSULATION,

 

CAP

 

CAP

DISCARD

 

 

 

 

 

BOTH

 

 

 

PIECES and

 

 

 

HEAT SHIELD

HEAT

SHIELD

HEAT

DISCARDSHIELD INSULATION

and

HEAT SHIELD

CUT

HERE

Figure 18.

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Kensington Boulevard, Lakeville, MN 55044 USA Model SL-350TRSI-AUEHeat & Glo Quality Systems Table of Contents Diagram of SL-350TRSI-AUE Top Flue Installation InstructionsRear Flue Heat ShieldIntroduction Framing DimensionsSpace heaters Model Flue Termination Approvals Flue System ApprovalsIdentifying Flue Components Bustible Materials ALL around the PipeDVP90ST SL-90D Maximum 10.97M Vertical FlueingUSE SL D-SERIES USE DVP-SERIES Components onlyUSE DVP-SERIES USE SL D-SERIES Components Only Flueing with ONE 1 90 ElbowFT. M + H FT. M Flueing with TWO 2 90 ElbowsFlueing with TWO 2 90 Elbows + H1 FT. M Flueing with Three 3 90 ElbowsFlueing with Three 3 90 Elbows Installing Flue Components Assembling Flue Components Continue Adding Flue Components Install Support BracketsHole and New Framing Members Installing Support BracketsMust be Positioned SO That the Arrow is Pointing UP For Horizontal Terminations using the DVP-TRAPGas Supply Line Connecting the GAS SupplyElectronic Ignition Wiring Diagram Ignition System WiringBlower FAN Inches mm FinishingPilot Assembly Installer TestingInstalling the Trim LOG Placement Instructions Log Set Assembly LOGS-350CE-D Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Operating Instructions Trol Wiring System of this UnitOperating Cautions With Solid FuelDo not Connect 220/240 VAC to the Control Valve Safety & Lighting InformationFAN Operation Servicing and MaintenanceParts Replacement Removal of Components for ServiceAdjustments and Replacement Parts Removal of Covers for ServicingElectronic Ignition System TroubleshootingLog set assembly Replacement PartsSL-350TRSI-AUE Service Parts List Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Melbourne

SL-350TRSI-AUE specifications

The Hearth and Home Technologies SL-350TRSI-AUE is a remarkable addition to the realm of contemporary fireplace solutions, designed to enhance both aesthetics and functionality in homes. This model exemplifies the company’s commitment to creating high-quality heating appliances that not only provide warmth but also serve as a stunning centerpiece for any living space.

One of the key features of the SL-350TRSI-AUE is its state-of-the-art linear design. This fireplace is constructed to provide a clean, modern aesthetic that seamlessly integrates into a variety of interior styles. With a sleek frame and expansive glass viewing area, it offers a panoramic view of the flames, allowing for an immersive experience. The linear orientation also creates a more open feel in a room, making it a favored choice for contemporary living spaces.

In terms of technology, the SL-350TRSI-AUE is equipped with advanced direct vent capabilities, ensuring efficient combustion and enhanced safety. The direct vent system pulls air from outside for combustion and exhausts directly outside, maintaining indoor air quality and optimizing heating efficiency. This is particularly beneficial in energy-smart homes, where maintaining indoor air quality is paramount.

The fireplace also features a powerful, adjustable flame control, enabling users to customize their heating experience according to personal preferences. With its thermostat compatibility, homeowners can set their desired temperature, and the fireplace will automatically adjust to provide consistent warmth. This smart heating solution ensures comfort throughout the colder months while also keeping energy consumption in check.

With regard to installation, the SL-350TRSI-AUE offers versatility. Its flexible venting options allow for installation in various locations, whether it be on an exterior wall or in a basement. The unit is designed to work under a variety of building conditions, providing engineers and contractors with greater flexibility during the design and installation processes.

Additionally, the fireplace features a minimalist remote control, allowing users to operate the unit effortlessly from anywhere in the room. The combination of these features makes the Hearth and Home Technologies SL-350TRSI-AUE a practical yet stylish choice for those seeking an efficient and visually appealing heating solution. With its blend of modern design, advanced technology, and functionality, it stands out as an exemplary product in the competitive fireplace market.
Top Page Image Contents