Hearth and Home Technologies SL-350TRSI-AUE manual Operating Instructions, Operating Cautions

Page 30

2.0 OPERATING INSTRUCTIONS

This appliance is a balanced flue heater and is designed to operate with all combustion air being siphoned from the outside of the building and all exhaust gases ex- pelled to the outside of the building.

WARNING: THIS UNIT IS NOT FOR USE

!WITH SOLID FUEL.

The control system for this model is an electronic sys- tem which includes a gas control valve, pilot, thermo- couple, ignitor and electronic ignition module. The con- trols are located in the lower compartment behind the lower door, and access is gained by lifting the door up. See Figure 1.

WARNING: DO NOT CONNECT 240 VAC ! TO THE GAS CONTROL VALVE OR CON-

TROL WIRING SYSTEM OF THIS UNIT.

When lit for the first time, the appliance will emit a slight odor for an hour or two. This is due to paint and lubri- cants used in the manufacturing process. Additionally, for the first few minutes after each lighting, vapor may condense and fog the glass and the flames may be blue. After a few minutes this moisture will disappear and within 15-30 minutes the flames should become yellow.

The heater may produce a noise, caused from metal expansion and contraction as it heats up and cools down. This noise is similar to one that a furnace or heat duct may produce and does not affect the operation or lon- gevity of the heater.

OPERATING CAUTIONS

•This appliance may exhibit a slight carbon deposition.

•Do not place articles on or against this appliance.

•Do not use or store flammable materials near this appliance.

•Do not spray aerosols in the vicinity of this appli- ance while it is in operation.

•The DRESS GUARD IS fitted to this appliance to reduce the risk of fire or injury from burns and no part of it should be permanently removed. For pro- tection of young children or the infirm, a secondary guard is required.

•The glass door assembly must be in place and sealed and the fixed mesh DRESS GUARD must be in place on the fireplace before the unit can be placed into safe operation.

•Do not use this appliance if any part has been under water. Immediately call a qualified service techni- cian to inspect the unit and to replace any part of the control system and any gas control which has been underwater.

•Do not operate this appliance with the glass door removed, cracked, or broken. Replacement of the glass door should be done by a licensed or qualified person. Do not strike or slam the glass door.

•The glass door assembly shall only be replaced as a complete unit as supplied by the gas fireplace manufacturer. No substitute materials may be used.

FLAME SPARKER/

SENSOR

VALVE

 

REMOTE

 

CONTROL

 

ANT.

 

ON/OFF

PILOT

WALL SWITCH

 

IGNITION

IGNITION MODULE

MODULE

6VDC

(6V)

 

GROUND

NEUTRAL

HOT

BATTERY PORT

 

 

PLUG IN

ON/OFF

THERMOCOUPLE

BLOCK

SWITCH

(CONNECTED TO

 

BACK OF VALVE)

 

VALVE

GAS LINE

 

CONNECTED TO

 

BACK OF VALVE

 

Figure 37.

 

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

30

 

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Model SL-350TRSI-AUE Kensington Boulevard, Lakeville, MN 55044 USAHeat & Glo Quality Systems Table of Contents Diagram of SL-350TRSI-AUE Rear Flue Installation InstructionsTop Flue Heat ShieldFraming Dimensions IntroductionSpace heaters Identifying Flue Components Flue System ApprovalsModel Flue Termination Approvals Bustible Materials ALL around the PipeDVP90ST SL-90D USE SL D-SERIES Vertical FlueingMaximum 10.97M USE DVP-SERIES Components onlyUSE SL D-SERIES Components Only Flueing with ONE 1 90 Elbow FT. MUSE DVP-SERIES Flueing with TWO 2 90 Elbows + H FT. MFlueing with TWO 2 90 Elbows Flueing with Three 3 90 Elbows + H1 FT. MFlueing with Three 3 90 Elbows Installing Flue Components Assembling Flue Components Install Support Brackets Continue Adding Flue ComponentsInstalling Support Brackets Hole and New Framing MembersFor Horizontal Terminations using the DVP-TRAP Must be Positioned SO That the Arrow is Pointing UPConnecting the GAS Supply Gas Supply LineIgnition System Wiring Electronic Ignition Wiring DiagramBlower FAN Finishing Inches mmInstaller Testing Installing the TrimPilot Assembly LOG Placement Instructions Log Set Assembly LOGS-350CE-D Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Operating Cautions Trol Wiring System of this UnitOperating Instructions With Solid FuelSafety & Lighting Information Do not Connect 220/240 VAC to the Control ValveServicing and Maintenance FAN OperationAdjustments and Replacement Parts Removal of Components for ServiceParts Replacement Removal of Covers for ServicingTroubleshooting Electronic Ignition SystemReplacement Parts Log set assemblySL-350TRSI-AUE Service Parts List Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Melbourne

SL-350TRSI-AUE specifications

The Hearth and Home Technologies SL-350TRSI-AUE is a remarkable addition to the realm of contemporary fireplace solutions, designed to enhance both aesthetics and functionality in homes. This model exemplifies the company’s commitment to creating high-quality heating appliances that not only provide warmth but also serve as a stunning centerpiece for any living space.

One of the key features of the SL-350TRSI-AUE is its state-of-the-art linear design. This fireplace is constructed to provide a clean, modern aesthetic that seamlessly integrates into a variety of interior styles. With a sleek frame and expansive glass viewing area, it offers a panoramic view of the flames, allowing for an immersive experience. The linear orientation also creates a more open feel in a room, making it a favored choice for contemporary living spaces.

In terms of technology, the SL-350TRSI-AUE is equipped with advanced direct vent capabilities, ensuring efficient combustion and enhanced safety. The direct vent system pulls air from outside for combustion and exhausts directly outside, maintaining indoor air quality and optimizing heating efficiency. This is particularly beneficial in energy-smart homes, where maintaining indoor air quality is paramount.

The fireplace also features a powerful, adjustable flame control, enabling users to customize their heating experience according to personal preferences. With its thermostat compatibility, homeowners can set their desired temperature, and the fireplace will automatically adjust to provide consistent warmth. This smart heating solution ensures comfort throughout the colder months while also keeping energy consumption in check.

With regard to installation, the SL-350TRSI-AUE offers versatility. Its flexible venting options allow for installation in various locations, whether it be on an exterior wall or in a basement. The unit is designed to work under a variety of building conditions, providing engineers and contractors with greater flexibility during the design and installation processes.

Additionally, the fireplace features a minimalist remote control, allowing users to operate the unit effortlessly from anywhere in the room. The combination of these features makes the Hearth and Home Technologies SL-350TRSI-AUE a practical yet stylish choice for those seeking an efficient and visually appealing heating solution. With its blend of modern design, advanced technology, and functionality, it stands out as an exemplary product in the competitive fireplace market.
Top Page Image Contents