Hearth and Home Technologies SL-350TRSI-AUE manual Installing Support Brackets

Page 20

For Vertical Runs

The flue system must be supported every eight (8) feet (2.4 M) above the heater flue outlet by wall brackets.

To install support brackets for vertical runs:

•Attach wall brackets to the flue pipe and secure the wall bracket to the framing members with nails or screws.

WALL BRACKET

WALL STUD

8 FT.

(2.4m)

FLUE

OUTLET

1 INCH MIN.

(25mm)

Figure 24. Installing Support Brackets

4. Install Firestops

For Horizontal Runs - Firestops are REQUIRED on both sides of a combustible wall through which the flue passes.

To install firestops (heat shield) for horizontal runs that pass through either interior or exterior walls:

•Cut a 10-inch by 12-inch (254 mm X 305 mm) hole through the wall.

•Position the firestops on both sides of the hole pre- viously cut and secure the firestops with nails or screws.

•The pipe opening of the firestops MUST BE placed towards the bottom of the firestop.

•Continue the flue run through the firestop.

 

10" (254mm)

INTERIOR

 

WALL SHIELD

 

 

12" (305mm)

Figure 25.

Flue Pipe & Firestop

For Vertical Runs - One firestop is REQUIRED at the hole in each ceiling through which the flue passes.

To install firestops for vertical runs that pass through ceilings:

•Position a plumb bob directly over the center of the vertical flue component.

•Mark the ceiling to establish the centerpoint of the flue.

•Drill a hole or drive a nail through this center point.

•Check the floor above for any obstructions, such as wiring or plumbing runs.

•Reposition the heater and flue system, if neces- sary, to accommodate the ceiling joists and/or ob- structions.

•Cut a 10-inch X 10-inch (254mm X 305mm) hole through the ceiling, using the firestop pipe opening as a guide.

•Frame the hole with framing lumber the same size as the ceiling joists.

10" (254mm)

10” (254mm)

 

 

CHIMNEY

 

HOLE

NEW

EXISTING CEILING

JOISTS

FRAMING

MEMBERS

 

CEILING

 

Figure 26. Hole and New Framing Members

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model SL-350TRSI-AUE Kensington Boulevard, Lakeville, MN 55044 USAHeat & Glo Quality Systems Table of Contents Diagram of SL-350TRSI-AUE Installation Instructions Top FlueRear Flue Heat ShieldFraming Dimensions IntroductionSpace heaters Flue System Approvals Model Flue Termination ApprovalsIdentifying Flue Components Bustible Materials ALL around the PipeDVP90ST SL-90D Vertical Flueing Maximum 10.97MUSE SL D-SERIES USE DVP-SERIES Components onlyUSE DVP-SERIES USE SL D-SERIES Components Only Flueing with ONE 1 90 ElbowFT. M Flueing with TWO 2 90 Elbows + H FT. MFlueing with TWO 2 90 Elbows Flueing with Three 3 90 Elbows + H1 FT. MFlueing with Three 3 90 Elbows Installing Flue Components Assembling Flue Components Install Support Brackets Continue Adding Flue ComponentsInstalling Support Brackets Hole and New Framing MembersFor Horizontal Terminations using the DVP-TRAP Must be Positioned SO That the Arrow is Pointing UPConnecting the GAS Supply Gas Supply LineIgnition System Wiring Electronic Ignition Wiring DiagramBlower FAN Finishing Inches mmPilot Assembly Installer TestingInstalling the Trim LOG Placement Instructions Log Set Assembly LOGS-350CE-D Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Trol Wiring System of this Unit Operating InstructionsOperating Cautions With Solid FuelSafety & Lighting Information Do not Connect 220/240 VAC to the Control ValveServicing and Maintenance FAN OperationRemoval of Components for Service Parts ReplacementAdjustments and Replacement Parts Removal of Covers for ServicingTroubleshooting Electronic Ignition SystemReplacement Parts Log set assemblySL-350TRSI-AUE Service Parts List Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Melbourne

SL-350TRSI-AUE specifications

The Hearth and Home Technologies SL-350TRSI-AUE is a remarkable addition to the realm of contemporary fireplace solutions, designed to enhance both aesthetics and functionality in homes. This model exemplifies the company’s commitment to creating high-quality heating appliances that not only provide warmth but also serve as a stunning centerpiece for any living space.

One of the key features of the SL-350TRSI-AUE is its state-of-the-art linear design. This fireplace is constructed to provide a clean, modern aesthetic that seamlessly integrates into a variety of interior styles. With a sleek frame and expansive glass viewing area, it offers a panoramic view of the flames, allowing for an immersive experience. The linear orientation also creates a more open feel in a room, making it a favored choice for contemporary living spaces.

In terms of technology, the SL-350TRSI-AUE is equipped with advanced direct vent capabilities, ensuring efficient combustion and enhanced safety. The direct vent system pulls air from outside for combustion and exhausts directly outside, maintaining indoor air quality and optimizing heating efficiency. This is particularly beneficial in energy-smart homes, where maintaining indoor air quality is paramount.

The fireplace also features a powerful, adjustable flame control, enabling users to customize their heating experience according to personal preferences. With its thermostat compatibility, homeowners can set their desired temperature, and the fireplace will automatically adjust to provide consistent warmth. This smart heating solution ensures comfort throughout the colder months while also keeping energy consumption in check.

With regard to installation, the SL-350TRSI-AUE offers versatility. Its flexible venting options allow for installation in various locations, whether it be on an exterior wall or in a basement. The unit is designed to work under a variety of building conditions, providing engineers and contractors with greater flexibility during the design and installation processes.

Additionally, the fireplace features a minimalist remote control, allowing users to operate the unit effortlessly from anywhere in the room. The combination of these features makes the Hearth and Home Technologies SL-350TRSI-AUE a practical yet stylish choice for those seeking an efficient and visually appealing heating solution. With its blend of modern design, advanced technology, and functionality, it stands out as an exemplary product in the competitive fireplace market.
Top Page Image Contents