Hearth and Home Technologies SL-350TRSI-AUE Flue System Approvals, Identifying Flue Components

Page 8

TABLE 1

MODEL

FLUE TERMINATION APPROVALS

DVP-TRAP2 & SLK-01TRD HORIZONTAL TERMINATION CAP

SL-350TRSI-AUE

DVP-TVHW & SLK-991DA VERTICAL TERMINATION CAP

 

 

 

1.2 FLUE SYSTEM APPROVALS

These models have flue starting collars on both the top and the back of the unit. Depending upon the installa- tion, decide which ONE set of starting collars will be used to attach the flue system. The starting collar sealing cap must remain on the starting collar NOT used.

These models use SL-D-series direct flue components when using the TOP flue collars and DVP-series direct flue components when using the REAR flue collars.

WARNING: YOU MUST NOT MIX DVP-SERIES AND SL D-SERIES COMPONENTS IN ANY FLUE SYSTEM CONFIGURATION.

Approved flue system components are labeled for identification. NO OTHER FLUEING SYSTEMS OR COMPONENTS MAY BE USED. Detailed installation instructions are included with each flue termination kit and should be used in conjunction with this manual. Figure 5 below shows flue system components and terminations.

Identifying Flue Components

The flue systems installed on this gas fireplace may include one, two, or three 90° elbow assemblies. The relationships of vertical rise to horizontal run in flue configurations using 90° elbows MUST BE strictly

adhered to. The rise to run relationships are shown in the flueing drawings and tables on the next few pages.

If a 90° elbow is first attached to the unit, the maximum horizontal run is 2 feet (610mm).

WARNING: THIS GAS APPLIANCE AND FLUE AS- SEMBLY MUST FLUE DIRECTLY TO THE OUTSIDE AND MUST NEVER BE ATTACHED TO A CHIMNEY SERVING A SEPARATE SOLID FUEL BURNING AP- PLIANCE. EACH GAS APPLIANCE MUST USE A SEPARATE FLUE SYSTEM-COMMON FLUE SYS- TEMS ARE PROHIBITED.

CAUTION: UNDER NO CONDITION SHOULD COMBUSTIBLE MATERIAL BE CLOSER THAN 3 INCHES (2 1/2 INCHES (64MM) AT WALL FIRE-

STOPS) FROM THE TOP OF THE PIPE OR 1-INCH TO THE SIDESAND THE BOTTOM FOR HORIZONTAL SECTIONS OF THIS FLUE SYSTEM. VERTICAL SECTIONS OF THIS SYSTEM REQUIRE A MINI- MUM OF 1-INCH (25MM) CLEARANCE TO COM-

BUSTIBLE MATERIALS ALL AROUND THE PIPE.

For alternative installations, other than depicted, con- tact your dealer for further information.

Refer to Figure 5 for required clearances to flue terminals.

 

 

 

Flue system components

 

VERTICAL

 

STORM

 

 

 

COLLAR

 

 

TERMINATION

 

 

 

 

HORZONTAL

 

ROOF FLASHING

 

TERMINATION

 

 

 

 

 

 

 

HORIZONTAL PIPE

 

 

 

 

SUPPORT

 

 

 

 

PIPE LENGTH

 

WALL

 

 

 

 

FIRESTOP

 

 

 

 

90 DEGREE

 

 

 

 

ELBOW

CEILING

WALL BRACKET

 

 

 

 

Flue system termination kits

FIRESTOP

 

 

 

 

SL D-SERIES

DVP-SERIES

 

 

SLK-01TRD

SLK-991DA

DVP-TVHW DVP-TRAP2

 

Figure 6. Flue Components and Terminations

 

 

8

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

 

 

 

 

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model SL-350TRSI-AUE Kensington Boulevard, Lakeville, MN 55044 USAHeat & Glo Quality Systems Table of Contents Diagram of SL-350TRSI-AUE Installation Instructions Top FlueRear Flue Heat ShieldFraming Dimensions IntroductionSpace heaters Flue System Approvals Model Flue Termination ApprovalsIdentifying Flue Components Bustible Materials ALL around the PipeDVP90ST SL-90D Vertical Flueing Maximum 10.97MUSE SL D-SERIES USE DVP-SERIES Components onlyUSE DVP-SERIES USE SL D-SERIES Components Only Flueing with ONE 1 90 ElbowFT. M Flueing with TWO 2 90 Elbows + H FT. MFlueing with TWO 2 90 Elbows Flueing with Three 3 90 Elbows + H1 FT. MFlueing with Three 3 90 Elbows Installing Flue Components Assembling Flue Components Install Support Brackets Continue Adding Flue ComponentsInstalling Support Brackets Hole and New Framing MembersFor Horizontal Terminations using the DVP-TRAP Must be Positioned SO That the Arrow is Pointing UPConnecting the GAS Supply Gas Supply LineIgnition System Wiring Electronic Ignition Wiring DiagramBlower FAN Finishing Inches mmPilot Assembly Installer TestingInstalling the Trim LOG Placement Instructions Log Set Assembly LOGS-350CE-D Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Trol Wiring System of this Unit Operating InstructionsOperating Cautions With Solid FuelSafety & Lighting Information Do not Connect 220/240 VAC to the Control ValveServicing and Maintenance FAN OperationRemoval of Components for Service Parts ReplacementAdjustments and Replacement Parts Removal of Covers for ServicingTroubleshooting Electronic Ignition SystemReplacement Parts Log set assemblySL-350TRSI-AUE Service Parts List Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Melbourne

SL-350TRSI-AUE specifications

The Hearth and Home Technologies SL-350TRSI-AUE is a remarkable addition to the realm of contemporary fireplace solutions, designed to enhance both aesthetics and functionality in homes. This model exemplifies the company’s commitment to creating high-quality heating appliances that not only provide warmth but also serve as a stunning centerpiece for any living space.

One of the key features of the SL-350TRSI-AUE is its state-of-the-art linear design. This fireplace is constructed to provide a clean, modern aesthetic that seamlessly integrates into a variety of interior styles. With a sleek frame and expansive glass viewing area, it offers a panoramic view of the flames, allowing for an immersive experience. The linear orientation also creates a more open feel in a room, making it a favored choice for contemporary living spaces.

In terms of technology, the SL-350TRSI-AUE is equipped with advanced direct vent capabilities, ensuring efficient combustion and enhanced safety. The direct vent system pulls air from outside for combustion and exhausts directly outside, maintaining indoor air quality and optimizing heating efficiency. This is particularly beneficial in energy-smart homes, where maintaining indoor air quality is paramount.

The fireplace also features a powerful, adjustable flame control, enabling users to customize their heating experience according to personal preferences. With its thermostat compatibility, homeowners can set their desired temperature, and the fireplace will automatically adjust to provide consistent warmth. This smart heating solution ensures comfort throughout the colder months while also keeping energy consumption in check.

With regard to installation, the SL-350TRSI-AUE offers versatility. Its flexible venting options allow for installation in various locations, whether it be on an exterior wall or in a basement. The unit is designed to work under a variety of building conditions, providing engineers and contractors with greater flexibility during the design and installation processes.

Additionally, the fireplace features a minimalist remote control, allowing users to operate the unit effortlessly from anywhere in the room. The combination of these features makes the Hearth and Home Technologies SL-350TRSI-AUE a practical yet stylish choice for those seeking an efficient and visually appealing heating solution. With its blend of modern design, advanced technology, and functionality, it stands out as an exemplary product in the competitive fireplace market.
Top Page Image Contents