Hearth and Home Technologies SL-350TRSI-AUE Removal of Covers for Servicing, Parts Replacement

Page 33

3.1REMOVAL OF COVERS FOR SERVICING

A. Control Compartment Door

•Rotate the lower door down to access the gas controls. B. Dress Guard and Glass Door

•Lift the front dress guard up and out away from the appliance side surrounds. Replace the dress guard when servicing is complete.

•Release the four glass clips around the glass door. Carefully lift the glass up and out away from the ap- pliance (see Figure 40).

LATCHES

(BOTH TOP

AND BOTTOM)

GLASS

ASSEMBLY

Figure 40. Glass Assembly

3.2REMOVAL OF COMPONENTS FOR SERVICE

1. BURNER

•Remove the screws holding the log grate. Carefully lift up and remove the log set, log grate, and metal base pan.

•Unscrew the brackets at both ends of the burner and the retaining screws at the pilot bracket (see Figure 41). Slide the burner towards the right away from the burner orifice.

PILOT BRACKET

RETAINING SCREWS

Figure 41.

CAUTION: ALL SCREWS WHICH WERE REMOVED MUST BE REPLACED.

2. PILOT ASSEMBLY/IGNITION SYSTEM

•Remove the log set, log grate, metal base pan and burner.

•Disconnect the gas supply tube from the underside of the gas valve and the thermocouple from the interruptor (black).

•Disconnect and remove the pilot assembly from the bracket.

NOTE: When removing the pilot assembly, carefully pull the electrode wire, detach from the assembly and leave in place for reconnection.

3.3PARTS REPLACEMENT

1. FAN/SWITCHES

•Disconnect the fan wires from the junction box wires by pulling the male and female connectors apart and slide the fan out the front of the lower controls com- partment.

•Disconnect the wires from the fan speed control switch, pull off the knob, and remove the nut holding the speed control to the bracket.

•Disconnect the wires from the fan temperature sen- sor switch and remove the nut holding the switch bracket onto the side of the firebox.

2. GLASS PANEL

•To replace the glass door, place the bottom edge on top of the bottom mounting brackets. Push glass against unit and latch the two fasteners at the top of the glass door and the two fasteners at the bottom (see Figure 40).

3.4ADJUSTMENTS AND REPLACEMENT PARTS

Adjustments and replacement parts for this appliance should only be done by a qualified service person. A wiring diagram for the appliance is shown in SECTION

2.0OPERATING INSTRUCTIONS. A replacement part table is shown in SECTION 4.0 of this manual.

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Kensington Boulevard, Lakeville, MN 55044 USA Model SL-350TRSI-AUEHeat & Glo Quality Systems Table of Contents Diagram of SL-350TRSI-AUE Top Flue Installation InstructionsRear Flue Heat ShieldIntroduction Framing DimensionsSpace heaters Model Flue Termination Approvals Flue System ApprovalsIdentifying Flue Components Bustible Materials ALL around the PipeDVP90ST SL-90D Maximum 10.97M Vertical FlueingUSE SL D-SERIES USE DVP-SERIES Components onlyUSE SL D-SERIES Components Only Flueing with ONE 1 90 Elbow FT. MUSE DVP-SERIES + H FT. M Flueing with TWO 2 90 ElbowsFlueing with TWO 2 90 Elbows + H1 FT. M Flueing with Three 3 90 ElbowsFlueing with Three 3 90 Elbows Installing Flue Components Assembling Flue Components Continue Adding Flue Components Install Support BracketsHole and New Framing Members Installing Support BracketsMust be Positioned SO That the Arrow is Pointing UP For Horizontal Terminations using the DVP-TRAPGas Supply Line Connecting the GAS SupplyElectronic Ignition Wiring Diagram Ignition System WiringBlower FAN Inches mm FinishingInstaller Testing Installing the TrimPilot Assembly LOG Placement Instructions Log Set Assembly LOGS-350CE-D Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Operating Instructions Trol Wiring System of this UnitOperating Cautions With Solid FuelDo not Connect 220/240 VAC to the Control Valve Safety & Lighting InformationFAN Operation Servicing and MaintenanceParts Replacement Removal of Components for ServiceAdjustments and Replacement Parts Removal of Covers for ServicingElectronic Ignition System TroubleshootingLog set assembly Replacement PartsSL-350TRSI-AUE Service Parts List Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Melbourne

SL-350TRSI-AUE specifications

The Hearth and Home Technologies SL-350TRSI-AUE is a remarkable addition to the realm of contemporary fireplace solutions, designed to enhance both aesthetics and functionality in homes. This model exemplifies the company’s commitment to creating high-quality heating appliances that not only provide warmth but also serve as a stunning centerpiece for any living space.

One of the key features of the SL-350TRSI-AUE is its state-of-the-art linear design. This fireplace is constructed to provide a clean, modern aesthetic that seamlessly integrates into a variety of interior styles. With a sleek frame and expansive glass viewing area, it offers a panoramic view of the flames, allowing for an immersive experience. The linear orientation also creates a more open feel in a room, making it a favored choice for contemporary living spaces.

In terms of technology, the SL-350TRSI-AUE is equipped with advanced direct vent capabilities, ensuring efficient combustion and enhanced safety. The direct vent system pulls air from outside for combustion and exhausts directly outside, maintaining indoor air quality and optimizing heating efficiency. This is particularly beneficial in energy-smart homes, where maintaining indoor air quality is paramount.

The fireplace also features a powerful, adjustable flame control, enabling users to customize their heating experience according to personal preferences. With its thermostat compatibility, homeowners can set their desired temperature, and the fireplace will automatically adjust to provide consistent warmth. This smart heating solution ensures comfort throughout the colder months while also keeping energy consumption in check.

With regard to installation, the SL-350TRSI-AUE offers versatility. Its flexible venting options allow for installation in various locations, whether it be on an exterior wall or in a basement. The unit is designed to work under a variety of building conditions, providing engineers and contractors with greater flexibility during the design and installation processes.

Additionally, the fireplace features a minimalist remote control, allowing users to operate the unit effortlessly from anywhere in the room. The combination of these features makes the Hearth and Home Technologies SL-350TRSI-AUE a practical yet stylish choice for those seeking an efficient and visually appealing heating solution. With its blend of modern design, advanced technology, and functionality, it stands out as an exemplary product in the competitive fireplace market.
Top Page Image Contents