Hearth and Home Technologies SL-350TRSI-AUE manual Introduction, Framing Dimensions

Page 6

Minimum Clearances

from the Fireplace to Combustible Materials

 

Inches

mm

Glass Front

...................................... 36

914

Floor

0

0

Rear

1/2

13

Sides

1/2

13

Top

1 1/2

38

Ceiling*

31

787

*The clearance to ceiling is measured from the top of the unit, excluding the standoffs (see Figure 34).

Minimum Clearances

from the Vent Pipe to Combustible Materials

 

Inches

mm

Vertical Sections

1

25

Horizontal Sections

 

 

Top

3

75

Bottom

1

25

Sides

1

25

At Wall Firestops

 

 

Top

3

75

Bottom

1

25

Sides

1

25

For minimum clearances, see the direct vent termina- tion clearance in Figure 5.

E

Framing should be constructed

of 2 X 4 lumber or heavier.

D

B

The framing headers A may rest on the

fireplace stand-offs.

C

*NOTE: The center of the framing hole is one inch (254mm) above the center of the horizontal flue pipe.

A

B

C

D*

E*

34"

30-5/8"

16 1/2"

41-3/4"

21-1/4"

(864mm)

( 778mm)

(419mm)

(1060mm)

(540mm)

Figure 4. Framing Dimensions

CAUTION: Measure heater dimensions, and verify framing methods and wall covering details before fram- ing construction begins.

1.1 INTRODUCTION

This model is designed to operate with all combus- tion air being siphoned from the outside of the build- ing and all exhaust gases expelled to the outside of the building.

WARNING: THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

These units MUST use the flue termination described in the flueing section of the manual.

The control system for this model is an electronic igni- tion type. It consists of a gas control valve/variable regu- lator, a pilot/sensor/electrode and an ON/OFF switch. The controls are located behind the access door. Ro- tate the door down to open. See Figure 1.

Minimum inlet gas supply pressure for purpose of in- put adjustment is 4.5 inches w.c. (1.13kPa) for natural gas and 11 inches w.c. (2.75kPa) for propane. Mani- fold (outlet) pressures should be set at 3.5 inches w.c. (.8kPa) for natural gas models and 9.5 inches w.c. (2.36kPa) for propane models.

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model SL-350TRSI-AUE Kensington Boulevard, Lakeville, MN 55044 USAHeat & Glo Quality Systems Table of Contents Diagram of SL-350TRSI-AUE Rear Flue Installation InstructionsTop Flue Heat ShieldFraming Dimensions IntroductionSpace heaters Identifying Flue Components Flue System ApprovalsModel Flue Termination Approvals Bustible Materials ALL around the PipeDVP90ST SL-90D USE SL D-SERIES Vertical FlueingMaximum 10.97M USE DVP-SERIES Components onlyUSE SL D-SERIES Components Only Flueing with ONE 1 90 Elbow FT. MUSE DVP-SERIES Flueing with TWO 2 90 Elbows + H FT. MFlueing with TWO 2 90 Elbows Flueing with Three 3 90 Elbows + H1 FT. MFlueing with Three 3 90 Elbows Installing Flue Components Assembling Flue Components Install Support Brackets Continue Adding Flue ComponentsInstalling Support Brackets Hole and New Framing MembersFor Horizontal Terminations using the DVP-TRAP Must be Positioned SO That the Arrow is Pointing UPConnecting the GAS Supply Gas Supply LineIgnition System Wiring Electronic Ignition Wiring DiagramBlower FAN Finishing Inches mmInstaller Testing Installing the TrimPilot Assembly LOG Placement Instructions Log Set Assembly LOGS-350CE-D Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Operating Cautions Trol Wiring System of this UnitOperating Instructions With Solid FuelSafety & Lighting Information Do not Connect 220/240 VAC to the Control ValveServicing and Maintenance FAN OperationAdjustments and Replacement Parts Removal of Components for ServiceParts Replacement Removal of Covers for ServicingTroubleshooting Electronic Ignition SystemReplacement Parts Log set assemblySL-350TRSI-AUE Service Parts List Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Melbourne

SL-350TRSI-AUE specifications

The Hearth and Home Technologies SL-350TRSI-AUE is a remarkable addition to the realm of contemporary fireplace solutions, designed to enhance both aesthetics and functionality in homes. This model exemplifies the company’s commitment to creating high-quality heating appliances that not only provide warmth but also serve as a stunning centerpiece for any living space.

One of the key features of the SL-350TRSI-AUE is its state-of-the-art linear design. This fireplace is constructed to provide a clean, modern aesthetic that seamlessly integrates into a variety of interior styles. With a sleek frame and expansive glass viewing area, it offers a panoramic view of the flames, allowing for an immersive experience. The linear orientation also creates a more open feel in a room, making it a favored choice for contemporary living spaces.

In terms of technology, the SL-350TRSI-AUE is equipped with advanced direct vent capabilities, ensuring efficient combustion and enhanced safety. The direct vent system pulls air from outside for combustion and exhausts directly outside, maintaining indoor air quality and optimizing heating efficiency. This is particularly beneficial in energy-smart homes, where maintaining indoor air quality is paramount.

The fireplace also features a powerful, adjustable flame control, enabling users to customize their heating experience according to personal preferences. With its thermostat compatibility, homeowners can set their desired temperature, and the fireplace will automatically adjust to provide consistent warmth. This smart heating solution ensures comfort throughout the colder months while also keeping energy consumption in check.

With regard to installation, the SL-350TRSI-AUE offers versatility. Its flexible venting options allow for installation in various locations, whether it be on an exterior wall or in a basement. The unit is designed to work under a variety of building conditions, providing engineers and contractors with greater flexibility during the design and installation processes.

Additionally, the fireplace features a minimalist remote control, allowing users to operate the unit effortlessly from anywhere in the room. The combination of these features makes the Hearth and Home Technologies SL-350TRSI-AUE a practical yet stylish choice for those seeking an efficient and visually appealing heating solution. With its blend of modern design, advanced technology, and functionality, it stands out as an exemplary product in the competitive fireplace market.
Top Page Image Contents