Hearth and Home Technologies SL-350TRSI-AUE manual Installation Instructions, Top Flue, Rear Flue

Page 5

Top Flue

1in. Min. (25mm)

B

A

E

D

C

½ in. Min (13mm)

 

 

A

B

C

D

E

 

 

Millimeter

837

413

728

1001

1416

 

 

 

 

 

 

 

 

 

Rear Flue

1 in. MIN. (25mm)

B

A

E

D

C

1 in. MIN. (25mm)

 

A

B

C

D

E

Millimeter

837

413

843

1192

1686

Figure 2. Fireplace Dimensions, Locations, and Space Requirements

Clearance Requirements

The top and back of fireplace are defined by stand-offs.

The heat shield must be attached as shown if combus- tible materials are placed directly on top standoffs (Fig- ure 3).

The minimum clearance to a perpendicular wall ex- tending past the face of the fireplace is 25mm.

The back of the fireplaces may be recessed into com- bustible construction, as shown above.

TOP

 

STANDOFFS

 

INSTALLED

 

HEAT SHIELD

 

HEAT SHIELD

Figure 3.

Heat Shield

1.0 INSTALLATION INSTRUCTIONS

NOTE: Not intended for fireplace insert.

In planning the installation for the heater it is necessary to determine where the unit is to be installed, the type of flue system to be used (straight out, corner, or el- evated), and whether optional accessories (wall switch or remote control) are desired. Gas supply piping should also be planned. Refer to the appliance data plate on the base pan of the heater for all gas pressures and input rate information.

The heater can be mounted on any of the following sur- face:

1.A flat surface (minimum 6mm base).

2.Four (4) corner supports.

(Example: Four (4) concrete masonry blocks). These supports must be positioned so they contact all four (4) perimeter edges on the bottom of the unit.

Heater framing can be built before or after the heater is set in place. Framing should be positioned to accom- modate wall covering and heater facing material. The heater framing should be constructed of 2" X 4" (51 x 102mm) lumber or heavier. The framing headers may rest on the heater standoffs. Refer to Figure 2 and Fig- ure 4 for heater and framing reference dimensions.

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Kensington Boulevard, Lakeville, MN 55044 USA Model SL-350TRSI-AUEHeat & Glo Quality Systems Table of Contents Diagram of SL-350TRSI-AUE Top Flue Installation InstructionsRear Flue Heat ShieldIntroduction Framing DimensionsSpace heaters Model Flue Termination Approvals Flue System ApprovalsIdentifying Flue Components Bustible Materials ALL around the PipeDVP90ST SL-90D Maximum 10.97M Vertical FlueingUSE SL D-SERIES USE DVP-SERIES Components onlyUSE DVP-SERIES USE SL D-SERIES Components Only Flueing with ONE 1 90 ElbowFT. M + H FT. M Flueing with TWO 2 90 ElbowsFlueing with TWO 2 90 Elbows + H1 FT. M Flueing with Three 3 90 ElbowsFlueing with Three 3 90 Elbows Installing Flue Components Assembling Flue Components Continue Adding Flue Components Install Support BracketsHole and New Framing Members Installing Support BracketsMust be Positioned SO That the Arrow is Pointing UP For Horizontal Terminations using the DVP-TRAPGas Supply Line Connecting the GAS SupplyElectronic Ignition Wiring Diagram Ignition System WiringBlower FAN Inches mm FinishingPilot Assembly Installer TestingInstalling the Trim LOG Placement Instructions Log Set Assembly LOGS-350CE-D Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Operating Instructions Trol Wiring System of this UnitOperating Cautions With Solid FuelDo not Connect 220/240 VAC to the Control Valve Safety & Lighting InformationFAN Operation Servicing and MaintenanceParts Replacement Removal of Components for ServiceAdjustments and Replacement Parts Removal of Covers for ServicingElectronic Ignition System TroubleshootingLog set assembly Replacement PartsSL-350TRSI-AUE Service Parts List Heat & Glo SL-350TRSI-AUE 2089-902 Rev. B 6/06 Melbourne

SL-350TRSI-AUE specifications

The Hearth and Home Technologies SL-350TRSI-AUE is a remarkable addition to the realm of contemporary fireplace solutions, designed to enhance both aesthetics and functionality in homes. This model exemplifies the company’s commitment to creating high-quality heating appliances that not only provide warmth but also serve as a stunning centerpiece for any living space.

One of the key features of the SL-350TRSI-AUE is its state-of-the-art linear design. This fireplace is constructed to provide a clean, modern aesthetic that seamlessly integrates into a variety of interior styles. With a sleek frame and expansive glass viewing area, it offers a panoramic view of the flames, allowing for an immersive experience. The linear orientation also creates a more open feel in a room, making it a favored choice for contemporary living spaces.

In terms of technology, the SL-350TRSI-AUE is equipped with advanced direct vent capabilities, ensuring efficient combustion and enhanced safety. The direct vent system pulls air from outside for combustion and exhausts directly outside, maintaining indoor air quality and optimizing heating efficiency. This is particularly beneficial in energy-smart homes, where maintaining indoor air quality is paramount.

The fireplace also features a powerful, adjustable flame control, enabling users to customize their heating experience according to personal preferences. With its thermostat compatibility, homeowners can set their desired temperature, and the fireplace will automatically adjust to provide consistent warmth. This smart heating solution ensures comfort throughout the colder months while also keeping energy consumption in check.

With regard to installation, the SL-350TRSI-AUE offers versatility. Its flexible venting options allow for installation in various locations, whether it be on an exterior wall or in a basement. The unit is designed to work under a variety of building conditions, providing engineers and contractors with greater flexibility during the design and installation processes.

Additionally, the fireplace features a minimalist remote control, allowing users to operate the unit effortlessly from anywhere in the room. The combination of these features makes the Hearth and Home Technologies SL-350TRSI-AUE a practical yet stylish choice for those seeking an efficient and visually appealing heating solution. With its blend of modern design, advanced technology, and functionality, it stands out as an exemplary product in the competitive fireplace market.
Top Page Image Contents