Hearth and Home Technologies GDST3831I owner manual Vent Components Diagrams

Page 56

B. Vent Components Diagrams

		6-1/2 in.
	6-1/2 in.	165 mm
	6-1/2 in.
	165 mm
8-3/4 in.		6-1/2 in.
8-3/4 in.		165 mm9-1/4 in.
222 mm	6 in.	165 mm9-1/4 in.
	6 in.	235 mm
	152 mm
	6-5/8 in.
	168 mm	6-5/8 in.
	SLP45	6-5/8 in.
	SLP45	168 mm
	45° Elbow	9-7/8 in.
		251 mm

SLP90

90° Elbow

Effective Height/Length

		Pipe	inches	mm
Effective		SLP4	4	102
Effective		SLP6	6	152
Height/		SLP6	6	152
Height/		SLP12	12	305
Length		SLP12	12	305
Length		SLP24	24	610
		SLP24	24	610
		SLP36	36	914
		SLP48	48	1219
	SLP-PIPE	SLP6A	2 - 6	51 - 152
	SLP-PIPE	SLP12A	2 - 12	51 - 305
		SLP12A	2 - 12	51 - 305
		SLP-FLEX-2	24	610
		SLP-FLEX-3	36	914
		SLP-FLEX-5	60	1524
		SLP-FLEX-10	120	3048

EFFECTIVE HEIGHT/

LENGTH

SLP-FLEX-PIPE

26in.

660mm

DVP-HSM-B

Extended Heat Shield

SLP-HVS	RF4-8	SLP-FS	SLP-WS
Horizontal Pipe	Roof Flashing	Ceiling Firestop	Wall Shield Firestop
Support

Figure 16.2 SLP Series Vent Components

56	Heatilator • GDST3831I • 2127-900 Rev. F • 10/08

Image 56

Contents Models What to do if you smell gasDo Discardnot HOT SurfacesXxxxxxxx CongratulationsHomeowner Reference Information Table of Contents User GuideAppliance Setup TroubleshootingElectrical Information FinishingCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of MassachusettsYour Fireplace Gas Fireplace SafetyOperating Instructions User Guide Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesFan Kit optional Clear SpaceLighting Instructions IPI Final inspection byDo not Connect 110 VAC to the Control Valve What to do if YOU Smell GASAfter Fireplace is Lit Frequently Asked QuestionsIssue Solutions Maintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote ControlMaintenance Tasks-Qualiﬁed Service Technician Gasket Seal and Glass Assembly InspectionVenting LogsBurner Ignition and Operation IPI Pilot Flame PatternsGetting Started Typical Appliance SystemInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Framing and Clearances Selecting Appliance LocationClearances Minimum Framing DimensionsConstructing the Appliance Chase Mantel and Wall Projections TOP View Fireplace OpeningTermination Locations Vent Termination Minimum ClearancesCovered Alcove Applications Install Support Brackets To Install the Heat ShieldContinue Adding Vent Components CorrectVent Information and Diagrams Approved PipeVent Table Key Use of ElbowsUse of Flex Vent V1 Minimum H1 Maximum Vent DiagramsTop Vent Horizontal Termination One Elbow Top Vent Horizontal Termination Two Elbows V1 Minimum H1 + H2 MaximumTop Vent Horizontal Termination Three Elbows V1 Minimum H1 + H2 Maximum V1 + V2 MinExhaust restrictor Instructions Two Elbows Three Elbows Minimum Maximum + V 2 MinVent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall PenetrationInstall the Ceiling Firestop Pipe SLPVaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Appliance Preparation Securing and Leveling the ApplianceInstalling Vent Pipe Assemble Vent SectionsAssemble Slip Sections Securing the Vent SectionsInstalling Decorative Ceiling Components Disassemble Vent SectionsInstalling Metal Roof Flashing Assemble and Install Storm CollarInstall RF4-8 Apply Sealant TOP & Partial SidesHeat Shield Requirements for Horizontal Termination Installing Vertical Termination CapInstalling Decorative Wall Components Install Horizontal Termination Cap 22 Venting through the wallGas Information Fuel ConversionGas Pressure Gas ConnectionWiring Requirements Optional Accessories RequirementsElectrical Information Code CSA C22.1Intelliﬁre Ignition Wiring Diagram with Remote Receiver Junction Box Installation Wall Switch Installation for Fan OptionalFinishing To install the Splatter Guard Splatter GuardTo Close the Lower Access Panel To Remove the Splatter GuardAppliance Setup Pilot Install the Log AssemblyModels ST-550T-IPI. GDST3831I Notch Air Shutter Settings Install Trim Kits and SurroundsAir Shutter Setting Intelliﬁre Ignition System TroubleshootingSymptom Possible Cause Corrective Action Remove any contaminants that may have accumulated on Reference Materials Appliance Dimension DiagramElectrical Access Left View Front View GAS Line Right View Vent Components Diagrams Assembly SLP-DCF-BK SLK-SNKD SLP-CCS-BK SLP-TVHWSLP-TRAP1 SLP-TRAP2 DVP-2SL SLP-WT-BK SL-2DVPSLP-HRC-SS SLP-HRC-ZC-SS Horizontal Termination CAP DVP-TB1 Horizontal Termination CAPLog Set Assembly Service PartsService Parts List StockedAt Depot Description Comments Part NumberIntermittent Pilot Ignition Valve Assembly Contact Information