Hearth and Home Technologies RCOR-HVB-IPI, LCOR-HVB-IPI owner manual Diagram of the ST-HVB-IPI

Page 16

			5-14	1/2
			(133mm)	1/2
				(13mm)
				(4)
		12
		(306mm)
		Ø8
		(204mm)
	12	Ø8	46-5/8
	12	(204mm)	46-5/8
	(305mm)	(204mm)	(1183mm)
	(305mm)		(1183mm)
		42
		(1067mm)	32-5/16
			32-5/16
	ELECTRICAL		(820mm)		4-1/2
34-3/4	ACCESS		21		4-1/2
(882mm)			21		(114mm)
(882mm)			(533mm)		(114mm)
		GAS LINE	(533mm)
		GAS LINE
		ACCESS
				8-1/2
				(216mm)
4-1/16		2-5/16
4-1/16		(58mm)	36-3/16	24
(102mm)			(919mm)	24	2-9/16
4-1/2			(919mm)	(610mm)	2-9/16
4-1/2		4-3/4		(610mm)	(64mm)
(114mm)		(121mm)
TOP VENT
COLLARS
		TOP STANDOFFS		REAR VENT
				REAR VENT
				COLLARS
	GAS CONTROLS		SIDE GLASS
	& LABELS		DOOR
				GAS LINE
				ACCESS
				ELECTRICAL
				ACCESS
Figure 2.	Diagram of the ST-HVB-IPI
			16

Image 16

Contents ST-HVB-IPI LCOR-HVB-IPI RCOR-HVB-IPI What to do if you smell gasSafety and Warning Information Table of Contents Pier-HVB-IPI NG, LP Exploded Parts Diagram / Vue éclatée des pièces PIER-HVB-IPIST-HVB-IPI ST-HVB-IPI LCOR-HVB-IPI LCOR-HVB-IPI RCOR-HVB-IPI RCOR-HVB-IPI PIER-HVB-IPI, ST-HVB-IPI L&RCOR-HVB-IPI Installation Codes High Altitude Installations Appliance Certification CertificationIntroducing the Heat & Glo Gas Fireplaces Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the PIER-HVB-IPI Diagram of the ST-HVB-IPI Diagram of the LCOR-HVB-IPI and RCOR-HVB-IPI 121mmFireplace Dimensions and Locations Locating the FireplaceFraming the Fireplace Clearance RequirementsModel AT Each Joint Installing the Vent System Vent System ApprovalsTems or Components MAY be Used Identifying Vent ComponentsStraight UP Vertical Venting MAX .2 MStraight OUT Max. Run 24 610 mmVenting with One 90 Elbow Venting with Two 90 Elbows Venting with Two 90 Elbows Venting with three 90 elbows Venting with three 90 elbows Installing Vent Components Attach the First Vent Component to the Starting CollarsInstall Support Brackets Continue Adding Vent ComponentsAttic Firestop Positioned SO That the Arrow is Pointing UPVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Fireplace Gas Control SystemSecuring of a Fireplace Fireplace Junction BOX in a IPI SystemGas Supply Line Gas Pressure RequirementsOperation using Battery Power Wiring the Fireplace For Intermittent Pilot Ignition WiringAppliance Requirements Fan Wiring Diagram Optional Accessories Wall Switch Corner fan locationANY Manner FinishingHearth Extensions Installing Trim, Logs & Ember Material Using a 5/16 nut driver remove the two bolts see Figure Placing the Ember MaterialAfter the Installation Double-check for faulty componentsBefore Lighting the Fireplace Lighting the FireplaceFireplace Maintenance Important Turn OFF the GAS Before Servicing Your Fireplace